Effect of Resin Cements for Porcelain Veneers on the Color Stability after Accelerated Ageing

2012 ◽  
Vol 624 ◽  
pp. 216-220
Author(s):  
Jun Ai ◽  
Long Quan Shao ◽  
Shan Yu Zhou ◽  
Lin Lin Wang ◽  
Chen Hu ◽  
...  
Keyword(s):  
Total Energy ◽  
Color Change ◽  
Color Stability ◽  
The Other ◽  
Color Measurement ◽  
Accelerated Ageing ◽  
Distilled Water ◽  
Resin Cements ◽  
Before And After ◽  
Cie Lab

To assess the color stability of different resin cements after accelerated ageing. Four different resin cements were included in the study (1mm thickness). The resin cements were bonded to ceramic disks (0.5mm thickness) built with the VITABLOCS MARK-Ⅱ ceramic (n=7). All of the samples were stored in 37°C distilled water at dark. Then color measurement were determined using spectrophotometric before and after accelerated ageing in a weathering machine with a total energy of 150kJ/m2. Changes in color (ΔE) were obtained using the CIE Lab system coordinates where a ΔE data above 3 was accepted as visible discoloration. The ΔE of Superbond C&B, RelyX ARC, Variolink Veneer and Tetric Flow were 2.24±0.52, 2.47±0.28, 0.62±0.31 and 0.72±0.31 respectively. The Superbond C&B and RelyX ARC achieved significant higher ΔE than the other groups (P0.05). All of the resin cements assessed in this study show varying degrees of discoloration after accelerated ageing. However, the color change are not beyond the clinical aesthetic demand. And the Tetric Flow and Variolink Veneer demonstrate a higher color stability.

scholarly journals In Vitro Evaluation of Physical and Mechanical Properties of Light-Curing Resin Cement: A Comparative Study

2020 ◽  
Vol 14 (01) ◽  
pp. 152-156
Author(s):  
Luís Felipe Espíndola-Castro ◽  
Oscar Felipe Fonseca de Brito ◽  
Larissa Gabrielle Assis Araújo ◽  
Izabella Luiza Aragão Santos ◽  
Gabriela Queiroz De Melo Monteiro
Keyword(s):  
Color Change ◽  
Surface Hardness ◽  
Color Stability ◽  
Resin Cement ◽  
The Other ◽  
Distilled Water ◽  
Water Control ◽  
Mean Values ◽  
Significance Level

Abstract Objective The aim of study was to evaluate in vitro the surface hardness, sorption, solubility, and color stability of three light-cured resin cements, namely RelyX Veneer (RLX), Variolink Veneer (VLK), and All Cem Veneer (ACV). Materials and Methods Cylindrical samples (15 × 1 mm) were made for each group using a metallic mold (n = 10). Vickers microhardness test was performed, and average hardness was calculated from three indentations (300 gf/15s) per sample. The sorption and solubility of the materials were evaluated according to ISO 4049:2009 based on three samples weighing: initial (m 1), after immersion in distilled water for 7 days (m 2), and final (after removal of all moisture [m 3]). The color change was observed using a digital spectrophotometer, at three different time points, baseline, 1 day, and 1 week of immersion in coffee and distilled water (control). Statistical Analysis Shapiro–Wilk test was used to analyze the normality of the data, and groups were compared using Kruskal–Wallis and Mann–Whitney tests. A significance level of 5% was used. Results RLX showed the highest microhardness mean values (36.96 VHN), but higher sorption (23.2 µg/mm3) and solubility (2.40 µg/mm3), with statistically significant differences with the other groups. For color stability, higher ∆E was observed for the samples immersed in coffee (p = 0.009). The VLK resin cement presented statistically significant differences from the other groups, with higher color changes in coffee at 1 day (15.14) and after 1 week (23.65). Conclusion RLX resin cement showed better hardness results. All materials tested performed satisfactorily for sorption and solubility according to ISO 4049:2009. All materials showed high-staining values after 1 week of immersion in coffee.

scholarly journals The Effects of Mouthwashes on the Color Stability of Resin-Based Restorative Materials

2020 ◽  
pp. 346-357
Author(s):  
Ayşe Tuğba Ertürk-Avunduk ◽  
Seçkin Aksu ◽  
Ebru Delikan
Keyword(s):  
Analysis Of Variance ◽  
Color Change ◽  
Resin Composite ◽  
Color Stability ◽  
Multiple Comparison ◽  
Color Measurement ◽  
Distilled Water ◽  
Significant Difference ◽  
Restorative Materials ◽  
Post Hoc

Objective: This study investigated the effects of three types of mouthwash on the color stability of three resin-based restorative materials (nanohybrid resin composite, sonic-activated bulk-fill material, and compomer). Materials and Methods: To this end, 120 cylindrical disc specimens were prepared and polished, after which they were incubated in distilled water for 24 hours for post-polymerization. The baseline color values of each specimen were measured with a spectrophotometer, then the specimens were randomly divided into four groups. Following immersion in the mouthwashes for 24 hours, the specimens were rinsed with distilled water and dried before the color measurement was repeated. The values of color change (∆E₀₀) were subsequently calculated. A two-way analysis of variance and Duncan’s post hoc multiple comparison tests were conducted to determine statistically significant differences among the restorative materials. Results: All samples showed discoloration after immersion, albeit some instances of discoloration were imperceptible. In this respect, a statistically significant difference was found among the restorative materials and mouthwashes (p<0.05). Imperceptible ∆E₀₀ values were derived on the nanohybrid resin composite and compomer, but perceptible and acceptable ∆E₀₀ values were detected on the sonic-activated bulk-fill materials (p<0.05). The clinically unacceptable discoloration was observed on the sonic-activated bulk-fill composite immersed in Listerine®. Conclusions: Clinicians should make recommendations based on the potential staining capacity of mouthwashes prescribed for daily use in restorative materials. In this way, the need for renewal of restorations due to discoloration could be avoided.

scholarly journals Comparative evaluation of the color stability of universal composites

2021 ◽  
Vol 11 (Suppl. 1) ◽  
pp. 234-237
Author(s):  
Merve Gürses ◽  
Nevin Çobanoğlu ◽  
Omar Faez Abdulateef
Keyword(s):  
Comparative Evaluation ◽  
Color Change ◽  
Native Speakers ◽  
Color Stability ◽  
Composite Resins ◽  
Control Group ◽  
Distilled Water ◽  
Color Changes ◽  
Before And After ◽  
Native Speakers Of English

Aim: The aim of this study is to compare the color stability of different universal composites and to evaluate the effects of keeping them in water for 1 week before coloring. Methodology: Filtek Ultimate (FU), Estelite Ʃ Quick (EQ), and Ceram X One (CX) composites were used. The specimens were kept in the dark, dry environment for 24 hours, then polished, and each composite group was divided into 3 groups: the control, the group that was kept in water for 1 week before coloring and coloring (n=7). The samples in the control group were kept in distilled water for 3 weeks. Samples in the coloring group were colored with coffee for 2 weeks (C), and the samples in the last group were kept in water for 1 week and then stained with coffee for 2 weeks (W+C) (n=7). Color measurements for all samples were taken twice, once before and once after the coloring period. The color changes of the samples were measured using the ∆E* parameter, which was calculated with before and after measurements.  Results: For all composite resins, the ΔE values of the samples in the W+C and C groups were significantly higher than those in the control group. When the composites were compared with each other, the differences between the ΔE values of the composites in the control, W+C, and C groups were not statistically significant. For FU and ESQ, at the end of the coloration period, there were no statistically significant differences between the W+C and C groups. However, for CX, the color change of the samples in the W+C group was significantly higher than that in  the C group. Conclusion: Storage in distilled water for 1 week before staining did not reduce the color change values of the samples. Thus, after composite restorations are performed, there is no need to advise patients to avoid staining foods, especially in the first week after restoration.   How to cite this article: Abdulateef OF, Çobanoğlu N, Gürses M. Comparative evaluation of the color stability of universal composites. Int Dent Res 2021;11(Suppl.1):234-7. https://doi.org/10.5577/intdentres.2021.vol11.suppl1.34   Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

Effect of Two Matrix Metalloproteinase Inhibitors on the Color Stability of a Nanofilled Resin Composite

2015 ◽  
Vol 40 (1) ◽  
pp. E11-E20 ◽  
Author(s):  
M Iskander ◽  
D Elkassas ◽  
MA Mohsen
Keyword(s):  
Matrix Metalloproteinase ◽  
Total Energy ◽  
Color Change ◽  
Resin Composite ◽  
Measurement Data ◽  
Color Stability ◽  
Color Measurement ◽  
Control Group ◽  
Mmp Inhibitor ◽  
Occlusal Surfaces

SUMMARY Objectives This in vitro study evaluated the effect of two matrix metalloproteinase (MMP) inhibitors on the color stability of two shades of a nanofilled resin composite. Methods and Materials A total of 60 sound human molars were used in this study. Flat dentin surfaces were obtained by wet grinding the occlusal surfaces. Following acid etching, the molars were divided into three equal groups according to the MMP inhibitor used: Group 1: no inhibitor (control group), group 2: chlorhexidine digluconate based (CHX; Consepsis, Ultradent, South Jordan, UT, USA); group 3: doxycycline based (MTAD; Biopure, Dentsply TulsaDental, Johnson, TN, USA). Adper Single Bond 2 Adhesive (3M ESPE, St Paul, MN, USA) was applied to the treated dentin surfaces. Each group was then subdivided into two equal subgroups of 10 molars each, according to the shade of the resin composite (Filtek Z350 XT, 3M ESPE) used, either B1 or A3. The color was assessed for each subgroup at three times: baseline (after 24 hours); after aging using a total energy of 600 kJ/m2 (Weather-Ometer Ci35A, Atlas Electronic Devices Company, Chicago, IL, USA); and then after a second period of aging, for a total energy of 1200 kJ/m2. Color assessment was carried out using a spectrophotometer. Color change (ΔE) was calculated according to the Commission Internationale de l'Eclairage L*a* b* color scale, comparing each aging period with the baseline color measurement. Data were analyzed using repeated measures analysis of variance and Tukey post hoc test. Results All tested subgroups showed greater discoloration than the clinically acceptable level (3.3). MTAD induced the highest statistically significant color change, followed by CHX, whereas the control groups showed the lowest statistical ΔE values with both tested shades. Shade B1 subgroups showed higher ΔE values when compared with shade A3 subgroups. Conclusion Accelerated aging caused color change in a nanofilled resin composite regardless of MMP inhibitor used. Furthermore, lighter shades showed less color stability when compared with darker shades.

Color Stability of Resin Cements Exposed to Aging

2019 ◽  
Vol 44 (6) ◽  
pp. 609-614 ◽  
Author(s):  
NC Ramos ◽  
JN Luz ◽  
MC Valera ◽  
RM Melo ◽  
GSFA Saavedra ◽  
...  
Keyword(s):  
Analysis Of Variance ◽  
Artificial Aging ◽  
Resin Composite ◽  
Accelerated Aging ◽  
Color Stability ◽  
Distilled Water ◽  
Base Catalyst ◽  
Resin Cements ◽  
Tukey Test ◽  
Before And After

SUMMARY The aim of this study was to evaluate the color stability of light-cured and dual-cured resin cements after artificial accelerated aging. Ten specimens (6-mm diameter and 2-mm thickness) for each of five resin cements were prepared: GC (dual-cured cement, GCem), Vb (light-cured cement, Variolink II only the base), Vbc (dual-cured cement, Variolink II base with catalyst), VV (light-cured cement, Variolink Veneer), and FR (flowable resin composite, light cured). The samples were polished and stored in an accelerated artificial aging machine for 308 hours (160 klx), with cycles of 120 minutes under light and 60 minutes in the dark. All aging was carried out in distilled water at 37°C and light irradiation at 765 W/m2. The samples were evaluated in a spectrophotometer before and after aging, and results were calculated according to CIEDE2000. The data were statistically analyzed (one-way analysis of variance and Tukey test, 95% confidence). The results of ΔE00 were statistically significant for the type of cement (p&lt;0.001), with differences among tested groups. Variolink II (base only and base + catalyst) and the flowable resin were the cements with the lowest color variations after the artificial accelerated aging. Considering the values ΔE00 of acceptability and perceptibility, none of the tested cements showed acceptable values.

The Effects of Children's Drinks on the Color Stability of Various Restorative Materials

2009 ◽  
Vol 34 (2) ◽  
pp. 147-150 ◽  
Author(s):  
Emine Sen Tunc ◽  
Sule Bayrak ◽  
Ahmet Umut Guler ◽  
Nuray Tuloglu
Keyword(s):  
Study Design ◽  
Color Change ◽  
Grape Juice ◽  
Color Stability ◽  
Pediatric Dentistry ◽  
Distilled Water ◽  
Chocolate Milk ◽  
Restorative Material ◽  
Restorative Materials ◽  
Before And After

Objective: To evaluate the effects of exposure to various children's drinks on the color stability of different esthetic restorative material commonly used in pediatric dentistry. Study Design: Cylindrical specimens(15×2mm) were prepared from four different restorative materials (Fuji IX, Fuji II LC, Dyract Extra, and Filtek Z250). For each material, 20 specimens were prepared and divided into four groups. Each group was stored in a different solution (distilled water, chocolate milk, cola, grape juice) for 24 hours. A colorimeter was used to measure the color of each specimen both before and after staining. Color change (ΔE*) was calculated, and data was analyzed using two-way ANOVA and Tukey HSD tests. Results: For all restorative materials, the lowest ΔE* values were recorded for specimens stored in distilled water (0.42), followed by chocolate milk (0.88), grape juice (3.45) and cola (3.97). Among the four restorative materials tested,Fuji II LC showed the most color change (3.71) and Fuji IX the least (1.33). There were statistically significant differences among above groups (p&lt;0.05). Conclusions: ΔE* values were acceptable for all materials tested, with the exception of Fuji II LC. Therefore, the use of RMGIC should be avoided in anterior restorations in children due to esthetic reasons.

scholarly journals Influence of Resin Cements and Ceramic types on the Color Stability and Translucence of Laminate Veneers/ Influência dos Cimentos de Resina e Tipos Cerâmicos na Estabilidade da Cor e Translucidez das Facetas Laminadas

2021 ◽  
Vol 4 (5) ◽  
pp. 21410-21425
Author(s):  
Francisca Daniele Jardilino Silami ◽  
Cristian Sbardelotto ◽  
Rafaella Tonani- Torrieri ◽  
Rossana Pereira de Almeida ◽  
Carolina Noronha Ferraz de Arruda ◽  
...  
Keyword(s):  
Color Change ◽  
Color Stability ◽  
The Other ◽  
Resin Cements ◽  
Mechanical Cycling ◽  
Study Results ◽  
Significant Difference ◽  
Initial Color ◽  
Laminate Veneers

Objective: This study evaluated the color stability and translucence of resin cements in the fixation of ceramic veneers submitted to aging protocols. Material and Methods: Buccal faces of bovine incisors were planed up to dentin. Eighty ceramic veneers (1 mm) were prepared using two pressed ceramics (IPS e-maxPress and IPS e-maxZirpress, IvoclarVivadent). Before the initial color and translucence readouts (Vita EasyShade, VITA), the veneers were fixed with light (Variolink II, Ivoclar/Vivadent) or dual cured (Relyx U200, 3M ESPE) cements. The samples were submitted (n=10) to thermal mechanical cycling (1.200.000 cycles, 1,3Hz, 5°C/37°C/55°C); and no aging protocol (control). New color and translucence readouts were performed. The cement thickness was quantified by a double coordinate stereomicroscope (Nikon Measurescope) as a control of the study. Results: Data (3-way ANOVA, Tukey, p0,05) showed difference (p0.05) in the color change for both ceramics cemented with U200 with no aging protocol. In the other groups, there was no significant difference (p0.05). There was no difference for translucence regardless ceramics, cements, or aging protocol. Thermal mechanical cycling was not significant for optical changes of the ceramics tested. Conclusions: It was concluded that the color stability and translucence of ceramics with thickness of 1mm were not influenced by the cement when submitted to thermal mechanical cycling. 

Assessment of Color Stability of Treated Leathers with Silicone Oil and Polyethylene Glycol

2014 ◽  
Vol 1 (1) ◽  
pp. 24-34
Author(s):  
Alireza K. ◽  
Hossein Ahmadi ◽  
Mohsen Mohammadi
Keyword(s):  
Ascorbic Acid ◽  
Polyethylene Glycol ◽  
Treatment Process ◽  
Color Change ◽  
Silicone Oil ◽  
Accelerated Aging ◽  
Color Stability ◽  
Antioxidant Additive ◽  
Before And After ◽  
Aesthetic Values

Lubricants and leather dressings are the most common treatments of dry and water logged historical leathers. Color change has a great importance during the time and treatment process, due to visual and aesthetic values of historic leather relics. Polyethylene glycol (PEG) and silicone oil (SiO) are frequently used leather dressings in the conservation procedures. Therefore, color stability of treated leathers with PEG and SiO were investigated before and after heat accelerated aging. Moreover, application of ascorbic acid was evaluated as an antioxidant additive for PEG (PEG+AA).Color change after treatment and aging were studied by colorimetry technique in the CIE *L*a*b system. Results indicated to severe color alteration in PEG treated and aged leathers with or without ascorbic acid. Whereas, SiO treated samples showed better stability and minimum color shift after aging. Silicone oil was characterized as the best dressing for historical leathers with compared to PEG and PEG+AA, due to its high stability and aesthetical properties.

scholarly journals Evaluation of color stability of different temporary restorative materials

2015 ◽  
Vol 44 (5) ◽  
pp. 262-267 ◽  
Author(s):  
José Vitor Quinelli Mazaro ◽  
Luiz Miguel Minani ◽  
Adriana Cristina Zavanelli ◽  
Caroline Cantieri de Mello ◽  
Cleidiel Aparecido Araújo Lemos
Keyword(s):  
Storage Time ◽  
Color Change ◽  
Artificial Saliva ◽  
Color Stability ◽  
Time Interval ◽  
Acrylic Resins ◽  
Significant Difference ◽  
Restorative Materials ◽  
Before And After ◽  
Level Of Significance

AbstractIntroductionTemporary restorative materials are widely used, however, little is know about their color stability.Objectiveto evaluate the color stability of the following temporary restorative materials: acrylic and bis-acrylic resins after immersion in pigmenting solutions for different periods of storage.Material and methodFour materials were tested (Dêncor/Clássico, Protemp 4/3M ESPE; Structur 2 SC/Voco; Luxatemp AM Plus/DMG) and 30 test specimens (15 mm in diameter and 2 mm thick) per material were fabricated. They were divided according to the storage medium (artificial saliva, saliva + cola type soda, and saliva + coffee) and storage time intervals (2, 5, 7 and 15 days). Color measurements were made before and after immersions, with use of a spectrophotometer, by means of the CIE L*a*b* system. The data were analyzed by the analysis of variance and the Tukey Test, at a level of significance of 5%.ResultAcrylic resin presented greater color stability in comparison with bis-acrylic resins (p<0.001). When bis-acrylic resins were compared no significant difference was observed between the resins Structur and Luxatemp (p=0.767). As regards solutions tested, coffee showed the highest color change values (p<0.001), and the longer the storage time interval, the greater was the color change in all the temporary restorative materials analyzed (p<0.001).ConclusionAcrylic resin presented greater color stability in comparison with bis-acrylic resins (p<0.001). Coffee caused the greatest color change, and immersion time was determinant in color stability of the temporary materials analyzed.

scholarly journals Impact of mineral and organic absorbent during the discoloration of avocado oil by comparing with olive oil

2021 ◽  
Vol 16 (2) ◽  
pp. 113-121
Author(s):  
Orléans Ngomo ◽  
Joseph Sieliechi ◽  
Etienne Dongo
Keyword(s):  
Activated Carbon ◽  
Shelf Life ◽  
Olive Oil ◽  
Nutritional Quality ◽  
The Other ◽  
Added Value ◽  
Avocado Oil ◽  
Before And After ◽  
Valuable Product ◽  
Cie Lab

Avocado is a versatile and valuable product. Its oil is comparable to olive oil in terms of nutritional quality. It can also be used in cosmetics, in particular, in soaps, shampoos and lotions. Despite all these important attributes that avocado has, it is highly perishable and coupled with the lack of farm-to-market roads, a lot of it is lost after harvest during the peak season. The introduction of methods that will transform avocado to products with a long shelf life and added value will go a long way to solving the problem of post-harvest losses and poverty. One of these methods is the production of avocado oil. In addition, in order to reduce the colour of the pigments without altering their quality, discoloration tests were carried out by adsorption on bleaching grounds (a montmorillonite, a kaolinite and activated carbon). The colour intensities of the oils before and after adsorption were determined using two complementary methods: a UV-Vis spectrophotometer and a Konica Minolta spectrophotometer CM-5. The UV-Vis spectrophotometer show that the activated carbon has a best fixing capacity of the pigments; According to the Colorimetric parameters (CIE-Lab) the coordinates L* a* b* that showed brightness (L*) of the avocado oil was half of the olive oil (41.13±0.02 vs 84.85±0.02). The activated carbon was better in fixing the red (a*) (4.99±0.01vs 15.73±0.01 before adsorption) and yellow (b*) (63.71±0.09 vs 70.07±0.09 before adsorption) pigments, while the other two adsorbents have very little influence on the red colour of avocado oil. RésuméL’avocat est un produit versatile et de grande valeur. Son huile est comparable à huile d’olive en terme de qualité nutritionnelle ; elle peut également être utilisée en cosmétique en occurrence dans les savons, champoings et lotions. En pleine saison, l’on fait face à une abondance des avocats dans les zones de production qui sont très souvent enclavées ; c’est ainsi que face aux difficultés de transport et les routes peu praticables pour l’importation, l’on se retrouve en train de perdre de très importantes quantités d’avocats après les récoltes. Or la production d’huile d’avocats permettrait de réduire les pertes post récolte, réduirait le chômage et permettrait de lutter contre la pauvreté après la vente des huiles extraites. De plus, dans le but de réduire les pigments colorés, des tests de décolorations effectués par adsorption sur des terres décolorantes (une montmorillonite en provenance de Maroua, une kaolinite en provenance de Douala et le charbon actif) sont effectués. Les couleurs des huiles mesurées avant et après adsorption à l’aide deux appareils complémentaires : Le spectrophotomètre UV-Vis et du Konica Minolta spectrophotomètre CM-5 montrent. Les analyses spectrophotométriques UV-Vis montrent que c’est le charbon activé qui présente la meilleure adsorption des pigments ; D’après les coordonnées L*a*b*, la clarté de l’huile d’avocat est pratiquement la moitié de celle de l’huile d’olive (41,13±0,02 contre 84,85±0,02), le charbon activé fixe mieux les pigments rouges (a*) (4,99±0,01 contre 15,73±0,01 avant adsorption) et jaunes (b*) (63,71±0,09 contre 70,07±0,09 après adsorption), tandis que les deux autres adsorbants influencent très peu sur la coloration des huiles.

Sign in / Sign up

Export Citation Format

Share Document