scholarly journals Alkali-activated concretes based on fly ash and blast furnace slag: Compressive strength, water absorption and chloride permeability

2020 ◽  
Vol 40 (2) ◽  
Author(s):  
Daniela Eugenia Angulo-Ramírez ◽  
William Gustavo Valencia-Saavedra ◽  
Ruby Mejía de Gutiérrez
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Water Absorption ◽  
Blast Furnace Slag ◽  
Construction Materials ◽  
Chloride Ion ◽  
Chloride Permeability ◽  
Alkaline Activator ◽  
Furnace Slag

Concretes based on alkaliactivated binders have attracted considerable attention as new alternative construction materials, which can substitute Portland Cement (OPC) in several applications. These binders are obtained through the chemical reaction between an alkaline activator and reactive aluminosilicate materials, also named precursors. Commonly used precursors are fly ash (FA), blast furnace slag (GBFS), and metakaolin. The present study evaluated properties such as compressive strength, rate of water absorption (sorptivity), and chloride permeability in two types of alkaliactivated concretes (AAC): FA/GBFS 80/20 and GBFS/OPC 80/20. OPC and GBFS/OPC* concretes without alkaliactivation were used as reference materials. The highest compressive strength was observed in the FA/GBFS concrete, which reported 26,1% greater strength compared to OPC concrete after 28 days of curing. The compressive strength of alkaliactivated FA/GBFS 80/20 and GBFS/OPC 80/20 was 61 MPa and 42 MPa at 360 days of curing, respectively. These AAC showed low permeability to the chloride ion and a reduced water absorption. It is concluded that these materials have suitable properties for various applications in the construction sector.

Effect of Mineral Admixtures and Water/Binder Ratios on the Resistance to the Chloride Ions Penetration into Concrete

2011 ◽  
Vol 99-100 ◽  
pp. 758-761
Author(s):  
Yan Jun Hu ◽  
Yan Liang Du
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
Chloride Ion ◽  
Test Methods ◽  
Chloride Ions ◽  
Mineral Admixtures ◽  
Chloride Permeability ◽  
Furnace Slag

In this study, concrete prisms were made with three mineral admixtures: fly ash, blast furnace slag or silica fume and with three water-to-binder ratios(w/b). Chloride penetration was measured by the rapid chloride permeability test (RCPT)-ASTM C1202, 150-days ponding test and alternate wetting and drying test by cyclic loading with salt solution and oven drying, and the results by the three test methods were compared. This paper discussed the effects of mineral admixtures and w/b on the concrete chloride permeability. Blending concrete with blast furnace slag, fly ash or silica fume was beneficial with regard to the resistance against chloride ion penetration. Concrete specimens with lower w/b showed lower chloride permeability.

Effect of the Combined Using of Fly Ash and Granulated Blast Furnace Slag on Properties of Cementless Alkali-Activated Mortar

2011 ◽  
Vol 287-290 ◽  
pp. 916-921
Author(s):  
Kyung Taek Koh ◽  
Gum Sung Ryu ◽  
Si Hwan Kim ◽  
Jang Hwa Lee
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Curing Temperature ◽  
Mixture Ratio ◽  
Granulated Blast Furnace Slag ◽  
Alkaline Activator ◽  
Furnace Slag ◽  
Alkali Activated

This paper examines the effects of the mixture ratio of fly ash/slag, the type of alkaline activators and curing conditions on the workability, compressive strength and microstructure of cementless alkali-activated mortar. The investigation showed that the mixture ratio of fly ash/slag and the type of alkaline activator have significant influence on the workability and strength, whereas the curing temperature has relatively poor effect. An alkali-activated mortar using a binder composed of 50% of fly ash and 50% of granulated blast furnace slag and alkaline activator made of 9M NaOH and sodium silicate in proportion of 1:1 is seen to be able to develop a compressive strength of 65 MPa at age of 28 days even when cured at ambient temperature of 20°C.

Optimization of Concrete Porous Mix Using Slag as Substitute Material for Cement and Aggregates

2017 ◽  
Vol 865 ◽  
pp. 282-288 ◽  
Author(s):  
Jul Endawati ◽  
Rochaeti ◽  
R. Utami
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
Environmental Effect ◽  
Substitution Effect ◽  
Main Concern ◽  
Binder Material ◽  
Furnace Slag

In recent years, sustainability and environmental effect of concrete became the main concern. Substituting cement with the other cementitious material without decreasing mechanical properties of a mixture could save energy, reduce greenhouse effect due to mining, calcination and limestone refining. Therefore, some industrial by-products such as fly ash, silica fume, and Ground Iron Blast Furnace Slag (GIBFS) would be used in this study to substitute cement and aggregate. This substitution would be applied on the porous concrete mixture to minimize the environmental effect. Slag performance will be optimized by trying out variations of fly ash, silica fume, and slag as cement substitution material in mortar mixture. The result is narrowed into two types of substitution. First, reviewed from the fly ash substitution effect on binder material, highest compressive strength 16.2 MPa was obtained from mixture composition 6% fly ash, 3% silica fume and 17% grinding granular blast-furnace slag. Second, reviewed from slag types as cement substitution and silica fume substitution, highest compressive strength 15.2 MPa was obtained from mortar specimens with air-cooled blast furnace slag. It composed with binder material 56% Portland composite cement, 15% fly ash, 3% silica fume and 26% air-cooled blast furnace slag. Considering the cement substitution, the latter mixture was chosen.

scholarly journals Protective Geopolymer Coatings Containing Multi-Componential Precursors: Preparation and Basic Properties Characterization

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3448
Author(s):  
Chenhui Jiang ◽  
Aiying Wang ◽  
Xufan Bao ◽  
Zefeng Chen ◽  
Tongyuan Ni ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Adhesive Strength ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Rapid Test ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents an experimental investigation on geopolymer coatings (GPC) in terms of surface protection of civil structures. The GPC mixtures were prepared with a quadruple precursor simultaneously containing fly ash (FA), ground granulated blast-furnace slag (GBFS), metakaolin (MK), and Portland cement (OPC). Setting time, compressive along with adhesive strength and permeability, were tested and interpreted from a perspective of potential applications. The preferred GPC with favorable setting time (not shorter than 120 min) and desirable compressive strength (not lower than 35 MPa) was selected from 85 mixture formulations. The results indicate that balancing strength and setting behavior is viable with the aid of the multi-componential precursor and the mixture design based on total molar ratios of key oxides or chemical elements. Adhesive strength of the optimized GPC mixtures was ranged from 1.5 to 3.4 MPa. The induced charge passed based on a rapid test of coated concrete specimens with the preferred GPC was 30% lower than that of the uncoated ones. Setting time of GPC was positively correlated with η[Si/(Na+Al)]. An abrupt increase of setting time occurred when the molar ratio was greater than 1.1. Compressive strength of GPC was positively affected by mass contents of ground granulated blast furnace slag, metakaolin and ordinary Portland cement, and was negatively affected by mass content of fly ash, respectively. Sustained seawater immersion impaired the strength of GPC to a negligible extent. Overall, GPC potentially serves a double purpose of satisfying the usage requirements and achieving a cleaner future.

Development of High Performance Concrete Containing Admixture in Nuclear Power Plants

2013 ◽  
Vol 357-360 ◽  
pp. 1062-1065 ◽  
Author(s):  
Jeong Eun Kim ◽  
Wan Shin Park ◽  
Song Hui Yun ◽  
Do Gyeum Kim ◽  
Jea Myoung Noh
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Modulus Of Elasticity ◽  
Blast Furnace Slag ◽  
High Performance ◽  
Splitting Tensile Strength ◽  
Furnace Slag

This paper presents the results of an experimental study on the compressive strength, splitting tensile strength and modulus of elasticity characteristics of high performance concrete. These tests were carried out to evaluate the mechanical properties of HPC for up to 7 and 28 days. Mixtures were prepared with water to binder ratio of 0.40. Two mixtures were containing fly ash at 25%, silica fume at 5% cement replacement, respectively. Another mixture was contains blast furnace slag and fly ash at 25%. Three standard 100¥a200 cylinder specimens were prepared. HPC showed improvement in the compressive strength and splitting tensile strength when ordinary Portland cement was replaced with silica fume. Compare with specimens FA25 and BS25FA25, specimen SF5 showed much more modulus of elasticity. It shows that the use of the blast furnace slag of 25% and fly ash of 25% cement replacement has caused a small increase in compressive strength and splitting tensile strength and modulus of elasticity compared to the only use of fly ash of 25% at 28days. The results indicated that the use of blast furnace slag or silica fume provided the good performance compare to fly ash when the mechanical properties of the high performance concretes were taken into account.

scholarly journals Characteristics of Mortars with Blast Furnace Slag Powder and Mixed Fine Aggregates Containing Ferronickel-Slag Aggregate

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5879
Author(s):  
Sung-Ho Bae ◽  
Jae-In Lee ◽  
Se-Jin Choi
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Steel Slag ◽  
Chloride Ion ◽  
Recycling Rate ◽  
Fine Aggregate ◽  
Fine Aggregates ◽  
Ferronickel Slag ◽  
Furnace Slag

Recently, interest in environmentally friendly development has increased worldwide, especially in the construction industry. In this study, blast furnace slag powder (BFSP) and mixed steel fine aggregates were applied to cement mortars to reduce the environmental damage caused by the extraction of natural aggregate and to increase the recycling rate of steel by-products in the construction industry. We investigated the fluidity, compressive strength, tensile strength, accelerated carbonation depth, and chloride ion penetration resistance of mortars with steel slag aggregate and their dependence on the presence or absence of BFSP. Because the recycling rate of ferronickel slag is low and causes environmental problems, we considered mortar samples with mixed fine aggregates containing blast furnace slag fine aggregate (BSA) and ferronickel slag fine aggregate (FSA). The results showed that the 7-day compressive strength of a sample containing both 25% BSA and 25% FSA was nearly 14.8% higher than that of the control sample. This trend is likely due to the high density and angular shape of steel slag particles. The 56-day compressive strength of the sample with BFSP and 50% FSA was approximately 64.9 MPa, which was higher than that of other samples with BFSP. In addition, the chloride ion penetrability test result indicates that the use of BFSP has a greater effect than the use of steel slag aggregate on the chloride ion penetration resistance of mortar. Thus, the substitute rate of steel slag as aggregate can be substantially enhanced if BFSP and steel slag aggregate are used in an appropriate combination.

Sign in / Sign up

Export Citation Format

Share Document