Study on Bond Properties of Textile Reinforced Concrete

2013 ◽  
Vol 639-640 ◽  
pp. 334-340
Author(s):  
Wen Ling Tian ◽  
Li Min Zhang
Keyword(s):  
Reinforced Concrete ◽  
Epoxy Resin ◽  
Concrete Strength ◽  
Practical Method ◽  
Bond Properties ◽  
Textile Reinforced Concrete ◽  
Bond Behavior ◽  
Fine Grained ◽  
Pull Out ◽  
Concrete Matrix

Textile reinforced concrete (TRC) allows the light weight structures and offers a high effectiveness of the reinforcement by using continuous yarns. The study on the bond behavior between textile and concrete matrix is significant for the development of computational methods that analyze the textile reinforced concrete. The paper analyzes the bonding constitutive model of TRC and the bonding mechanism that the stress is transferred from fine concrete to textile, pointing out quadruple linear model can accurately reflect the bond behavior between fiber and concrete, illustrates the main influences on bond between the fine grained matrix and fabrics based on the pull-out test, the result reveals that with initial bond length increasing, the maximum pull force increases, and increasing concrete strength and improving workability of concrete matrix, epoxy resin impregnating and sand covering of textile as well as prestressing textile can increase the bond strength between textile and concrete. Finally the paper proposes that epoxy resin impregnating and 0.15 ~ 0.30mm sand covering of textile can be used as a practical method of improving bond properties in the engineering.

scholarly journals Synergistic Bond Properties of Different Deformed Steel Fibers Embedded in Mortars Wet-Sieved from Self-Compacting SFRC

2021 ◽  
Vol 11 (21) ◽  
pp. 10144
Author(s):  
Xinxin Ding ◽  
Haibin Geng ◽  
Minglei Zhao ◽  
Zhen Chen ◽  
Jie Li
Keyword(s):  
Bearing Capacity ◽  
Cross Sections ◽  
Steel Fiber ◽  
Concrete Strength ◽  
Ultimate Bearing Capacity ◽  
Steel Fibers ◽  
Unit Weight ◽  
Bond Properties ◽  
Pull Out ◽  
Concrete Matrix

Reliable bond of steel fiber in concrete is a key problem relating to the reinforcing effect of steel fiber on concrete matrix and for the guide in significance for the optimal design of the geometry and mechanical properties of steel fiber. In this paper, on the basis of multi-indices of evaluation for the bond properties of single hooked-end steel fiber, the indices for the evaluation of synergistic bond properties of different deformed steel fibers are proposed. The pull-out tests were carried out for different deformed steel fibers embedded in mortar wet-sieved from self-compacting SFRC with manufactured sand. Fourteen types of steel fibers were used, including six hooked-end, two crimped, four indentation, one milling, and one large-end. The bond strength, bond energy, and bond toughness of single and per unit weight steel fiber were evaluated with the correspondence to the loading status of cracking resistance, normal serviceability, and ultimate bearing capacity of concrete. Results show that the deformed steel fibers presented different bond behaviors, hooked-end, and crimped steel fibers with circular cross-sections and a tensile strength of higher than 1150 MPa have excellent effects of strengthening, energy dissipation, and toughening capacity on self-compacting concrete with a cubic compressive strength of 60 MPa at normal serviceability and ultimate bearing capacity. Indentation, milling, and large-end steel fibers are more suitable for reinforcing the concrete strength due to the rigid bond before concrete cracking. The synergistic working of steel fibers with concrete matrix should be concerned to realize the effects of only or simultaneously reinforcing the strength and toughness of concrete.

scholarly journals Use of Cement Suspension as an Alternative Matrix Material for Textile-Reinforced Concrete

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2127
Author(s):  
Richard Fürst ◽  
Eliška Fürst ◽  
Tomáš Vlach ◽  
Jakub Řepka ◽  
Marek Pokorný ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Epoxy Resin ◽  
High Performance Concrete ◽  
Bending Test ◽  
Resin Matrix ◽  
Cement Matrix ◽  
Sample Type ◽  
Textile Reinforced Concrete ◽  
Epoxy Resin Matrix ◽  
Four Point Bending

Textile-reinforced concrete (TRC) is a material consisting of high-performance concrete (HPC) and tensile reinforcement comprised of carbon roving with epoxy resin matrix. However, the problem of low epoxy resin resistance at higher temperatures persists. In this work, an alternative to the epoxy resin matrix, a non-combustible cement suspension (cement milk) which has proven stability at elevated temperatures, was evaluated. In the first part of the work, microscopic research was carried out to determine the distribution of particle sizes in the cement suspension. Subsequently, five series of plate samples differing in the type of cement and the method of textile reinforcement saturation were designed and prepared. Mechanical experiments (four-point bending tests) were carried out to verify the properties of each sample type. It was found that the highest efficiency of carbon roving saturation was achieved by using finer ground cement (CEM 52.5) and the pressure saturation method. Moreover, this solution also exhibited the best results in the four-point bending test. Finally, the use of CEM 52.5 in the cement matrix appears to be a feasible variant for TRC constructions that could overcome problems with its low temperature resistance.

Bond behaviour of chemically prestressed textile reinforced concrete

2019 ◽  
Author(s):  
Katarzyna Zdanowicz ◽  
Boso Schmidt ◽  
Hubert Naraniecki ◽  
Steffen Marx
Keyword(s):  
Reinforced Concrete ◽  
Bond Strength ◽  
Crack Width ◽  
Research Programme ◽  
Textile Reinforced Concrete ◽  
Self Compacting Concrete ◽  
Bond Behaviour ◽  
Bond Slip ◽  
Laser Sensors ◽  
Pull Out

<p>The bond behaviour of concrete specimens with carbon textile reinforcement was investigated in the presented research programme. Pull-out specimens were cast from self-compacting concrete with expansive admixtures and in this way chemical prestress was introduced. The aim of the research was to compare bond behaviour between prestressed specimens and non-prestressed control specimens. During pull-out tests, the pull-out force and notch opening were measured with a load cell and laser sensors. Further, bond - slip and pull-out force - crack width relationships were drawn and compared for prestressed and non-prestressed specimens. Chemically prestressed specimens reached 24% higher bond strength than non-prestressed ones. It can be therefore concluded, that chemical prestressing positively influences the bond behaviour of concrete with textile reinforcement and thus better utilisation of its properties can be provided.</p>

scholarly journals Flexural properties of load-holding reinforced concrete beams strengthened with textile-reinforced concrete under a chloride dry–wet cycle

2019 ◽  
Vol 14 ◽  
pp. 155892501984590 ◽  
Author(s):  
Shiping Yin ◽  
Yulin Yu ◽  
Mingwang Na
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Flexural Properties ◽  
Reinforcement Effect ◽  
Textile Reinforced Concrete ◽  
Cycle Number ◽  
Fine Grained ◽  
Strengthened Beam

To study the reinforcement effect of textile-reinforced concrete (TRC) on concrete structures in a marine environment, a four-point bending loading method was used for graded loading to analyze the influence of the dry–wet cycle number, the reinforcement method, and chopped fiber addition on the flexural properties of load-holding reinforced concrete beams reinforced with textile-reinforced concrete. The results show that with the increase of dry–wet cycle numbers, the crack width and deflection of beams develop faster and the bearing capacity decreases. The performance of the prefabricated textile-reinforced concrete plate is close to that of a cast-in-place textile-reinforced concrete in limiting crack, bearing capacity, and deflection deformation. The addition of chopped fibers in fine-grained concrete can improve the reinforcement effect of textile-reinforced concrete. Based on the experimental results and referring to the relevant design codes and literature, the calculation formula of the bearing capacity of TRC-strengthened beam with a secondary load is established, and the calculated values are in good agreement with the actual values.

Study on the Effect of Bond-Anchoring Factor on Bond Behavior between Deformed Bar and Shale Ceramic Concrete

2011 ◽  
Vol 403-408 ◽  
pp. 444-448
Author(s):  
Wei Jun Yang ◽  
Jie Yu ◽  
Yan Wang
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Comparative Analysis ◽  
Anchorage Length ◽  
Bond Behavior ◽  
Pull Out ◽  
Practical Project ◽  
Deformed Bar

In this paper, the effect of bond-anchoring factor on bond behavior between deformed bar and shale ceramic concrete was analyzed by four groups of pull-out tests with different anchorage length. And three reinforced concrete pull-out tests used for comparative analysis were prepared at the same time. We obtained a series of experimental data and based on these data .A more accurate formula was summed up. This formula has a high value in guiding the practical project to choose the anchorage length.

Experiment on the Bonding Performance of BFRP Bars Reinforced Concrete

2012 ◽  
Vol 174-177 ◽  
pp. 993-998 ◽  
Author(s):  
Shi Yong Jiang ◽  
Yong Ye ◽  
Wei Fei
Keyword(s):  
Reinforced Concrete ◽  
Failure Modes ◽  
Concrete Strength ◽  
Basalt Fiber ◽  
Test Methods ◽  
Load Level ◽  
Reinforced Plastics ◽  
Bonding Performance ◽  
Pull Out ◽  
Bonding Properties

Through the pull-out test methods, the concrete strength、reinforcement diameter Basalt Fiber Reinforced Plastics Bars、the anchorage length、 stirrup rate and other factors on the bonding properties of the BFRP reinforced concrete is analyzed. The BFRP bars and reinforcing steel bars bonding properties is compared. BFRP reinforced concrete bond failure mode has two types .As the concrete strength increases, the bond strength of the BFRP reinforced concrete increased. With the increase BFRP bars diameter and shear lag relationship, the cohesive force of the BFRP reinforced concrete decrease accordingly. And the failure modes of the shape of the BFRP reinforcement concrete in BFRP bonding properties with a big impact for the specimens’ configuration stirrups on the ductility. When BFRP bars loading under the same load level, the end of the slip is greater than the free end slip.

scholarly journals Mechanical Behavior of Fiber-to-concrete Interface in Textile Reinforced Concrete: Theoretical Model

2019 ◽  
Vol 8 (2) ◽  
pp. 70-78
Author(s):  
Shanshan Cheng
Keyword(s):  
Reinforced Concrete ◽  
Analytical Solution ◽  
Interfacial Shear Stress ◽  
Theoretical Models ◽  
Interfacial Bond ◽  
Textile Reinforced Concrete ◽  
Bond Slip ◽  
Bond Behavior ◽  
Concrete Interface

This paper presents a theoretical solution of a reinforcement-to-concrete interface model under pull-push loading. Expressions for the interfacial shear stress distribution and load-displacement history are derived for different loading stages. The full debonding propagation process is discussed in detail and the analytical solutions are verified by comparing with existing theoretical models. Results of the analytical solution are presented to illustrate how the bond length and local bond-slip law affect the interfacial bond behavior. While the case study in this paper is on textile reinforced concrete, the analytical solution is equally valid to similar mechanical cases such as rebar reinforced concretes.

Fine-Grained Fibre Concrete of Run-Of-Crusher Stone Using Volcanic Ash

2021 ◽  
Vol 1043 ◽  
pp. 61-65
Author(s):  
Tolya Khezhev ◽  
Aslan Kardanov ◽  
Eldar Bolotokov ◽  
Azamat Dottuyev ◽  
Ibrahim Mashfezh
Keyword(s):  
Reinforced Concrete ◽  
Raw Materials ◽  
Concrete Strength ◽  
Basalt Fiber ◽  
Strength Properties ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Fine Grained ◽  
Concrete Mixtures ◽  
Polyfunctional Additive

The results of the studies on the creation of self-compacting fine-grained fiber-reinforced concrete based on run-of-crusher stone with the use of a polyfunctional additive D-5 are presented. Compositions of self-compacting fine-grained fiber-reinforced concrete with the use of basalt fiber have been developed, which significantly reduce cement consumption and improve the characteristics of fine-grained concrete mixture and concrete. Using a polyfunctional additive D-5in mixtures makes it possible to increase the strength properties of fine-grained fiber-reinforced concrete while improving the concrete mixtures’ rheological characteristics. Replacement of cement up to 10% of the mass by ash fraction d<0.14 min fine-grained concrete mixtures does not cause a noticeable decrease in the concrete strength properties. The developed self-compacting fine-grained fiber-reinforced concretes have increased strength properties and have a low-cost price due to the use of local raw materials and run-of-crusher stone.

Sign in / Sign up

Export Citation Format

Share Document