Cryogenically Synthesized Mechanically Alloyed Calcia Stabilized Zirconia

2009 ◽  
Vol 67 ◽  
pp. 271-276 ◽  
Author(s):  
Raja Ram Prasad ◽  
B.S. Sunder Daniel
Keyword(s):  
Electron Microscopy ◽  
Phase Evolution ◽  
Precursor Powder ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Mechanically Alloyed ◽  
X Ray ◽  
Precursor Powders ◽  
Cryogenic Conditions ◽  
Scanning Electron

Precursor powder of calcia-stabilized zirconia (CSZ) with 4, 7 and 15 wt % was synthesized by mechanical alloying (MA) in cryogenic conditions. The phase evolution of the precursor powders over 100 hours of MA was analyzed by powder X-ray diffraction technique. Cylindrical shaped sensor elements of the calcined powders were fabricated in a uniaxial press followed by sintering at 15000C for 3 hours. Scanning electron microscopy (SEM) was used to analyze the microstructure of the sintered pellets. The co-relation between material compositions, microstructure of the sinter pellets and the electrical properties of the sensors are discussed.

scholarly journals A Study on the Characteristics of Cu–Mn–Dy Alloy Resistive Thin Films

Coatings ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 118 ◽  
Author(s):  
Ho-Yun Lee ◽  
Chi-Wei He ◽  
Ying-Chieh Lee ◽  
Da-Chuan Wu
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Annealing Temperature ◽  
Phase Evolution ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Temperature Coefficient Of Resistance ◽  
X Ray ◽  
Transmission Electronmicroscopy ◽  
Scanning Electron

Cu–Mn–Dy resistive thin films were prepared on glass and Al2O3 substrates, which wasachieved by co-sputtering the Cu–Mn alloy and dysprosium targets. The effects of the addition ofdysprosium on the electrical properties and microstructures of annealed Cu–Mn alloy films wereinvestigated. The composition, microstructural and phase evolution of Cu–Mn–Dy films werecharacterized using field emission scanning electron microscopy, transmission electronmicroscopy and X-ray diffraction. All Cu–Mn–Dy films showed an amorphous structure when theannealing temperature was set at 300 °C. After the annealing temperature was increased to 350 °C,the MnO and Cu phases had a significant presence in the Cu–Mn films. However, no MnO phaseswere observed in Cu–Mn–Dy films at 350 °C. Even Cu–Mn–Dy films annealed at 450 °C showedno MnO phases. This is because Dy addition can suppress MnO formation. Cu–Mn alloy filmswith 40% dysprosium addition that were annealed at 300 °C exhibited a higher resistivity of ∼2100 μΩ·cm with a temperature coefficient of resistance of –85 ppm/°C.

Interaction between Yttria Fully Stabilized Zirconia or Yttria-Zirconia Blended Face-Coat with Ti6Al4V during Investment Casting

2014 ◽  
Vol 1019 ◽  
pp. 302-310 ◽  
Author(s):  
Kalenda Mutombo ◽  
Christina Kgomo ◽  
P. Rossouw
Keyword(s):  
Electron Microscopy ◽  
Xrd Analysis ◽  
Experimental Results ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
X Ray ◽  
Hardness Tester ◽  
Alpha Case ◽  
Face Coat ◽  
Scanning Electron

The interaction between the Ti6Al4V alloy and the mould materials was investigated. The alpha-case was characterized by Vickers hardness tester, optical and scanning electron microscopy equipped with electron dispersive X-ray spectrometry (EDX). X-ray diffraction (XRD) analysis was performed on as cast and on YFSZ or YZ-Blended face-coats. From the experimental results, a distinct alpha-case formation was revealed. The YFSZ led to a thicker and harder alpha-case than the YZ-Blended face-coat. The EDX revealed the presence of Zr and Si elements in both alpha-cases. Therefore, from experimental results and thermodynamic calculations, pure ZrO2and SiO2may react with Ti.

Synthesis, Characterization, and Green Luminescence in ZnO Nanocages

2007 ◽  
Vol 7 (2) ◽  
pp. 481-485 ◽  
Author(s):  
Michael Snure ◽  
Ashutosh Tiwari
Keyword(s):  
Electron Microscopy ◽  
Optical Transmission ◽  
Deep Level ◽  
X Ray Diffraction ◽  
Green Luminescence ◽  
X Ray ◽  
Temperature Solution ◽  
Precursor Powders ◽  
Highly Porous ◽  
Scanning Electron

In this paper, we report the synthesis, characterization and observation of green luminescence in ZnO nanocages. A novel low temperature solution-based technique has been developed for growing highly porous ZnO nano-cages from coarse ZnO precursor powders. Various samples, prepared in this study, were characterized using several different characterization tools such as X-ray diffraction, Scanning Electron Microscopy, Energy Dispersive X-ray Spectroscopy, Raman, Photoluminescence and Optical Transmission Spectroscopy. It has been shown that ZnO nanocages exhibit green luminescence, with PL data showing a broad green peak at 510 nm. The shift and broadening in the luminescence peaks are understood to arise because of the onset of deep level defects in the system.

Influence of CeO2 Additive on the Phase Transformations of Zirconia from Zircon Ore by Carbothermal Reduction Process

2014 ◽  
Vol 602-603 ◽  
pp. 238-241 ◽  
Author(s):  
Teng Yu Wang ◽  
You Guo Xu ◽  
Zhao Hui Huang ◽  
Ming Hao Fang ◽  
Yan Gai Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Phase Transformations ◽  
Carbothermal Reduction ◽  
Heating Temperature ◽  
Reduction Process ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
X Ray ◽  
Additive Increase ◽  
Scanning Electron

This paper mainly discusses the influences of heating temperatures and CeO2 additive contents on the phase transformations of zirconia from zircon ore by carbothermal reduction. The phase transformations of zirconia from zircon ore by carbothermal reduction were monitored by X-ray diffraction. The microstructure of the product was characterized by scanning electron microscopy. The results show that without adding CeO2, the optimized heating temperature of zircon carbothermal reduction was 1600 °C and the main phases of the product were m-ZrO2, ZrC and β-SiC, t-ZrO2; After adding CeO2, the main phase of the products consists of t-ZrO2, m-ZrO2, ZrC and β-SiC when the heating temperature is 1600 °C. CeO2 additive can be introduced into zirconia lattice and can cause it to form cerium stabilized zirconia. Zirconia in the product would be turned into partially stabilized zirconia with cerium addition from 5 wt% to 20 wt%. However, the form of zirconia in the product is not changed greatly with the amount of CeO2 additive increase.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Environmental scanning electron microscopy of fresh human gallstones reveals new morphologies of precipitated calcium salts

1992 ◽  
Vol 50 (2) ◽  
pp. 1322-1323
Author(s):  
Howard S. Kaufman ◽  
Keith D. Lillemoe ◽  
John T. Mastovich ◽  
Henry A. Pitt
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Environmental Scanning Electron Microscopy ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
Calcium Salts ◽  
Cholesterol Gallstones ◽  
X Ray ◽  
Ca Carbonate ◽  
Scanning Electron

Gallstones contain precipitated cholesterol, calcium salts, and proteins. Calcium (Ca) bilirubinate, palmitate, phosphate, and carbonate occurring in gallstones have variable morphologies but characteristic windowless energy dispersive x-ray (EDX) spectra. Previous studies of gallstone microstructure and composition using scanning electron microscopy (SEM) with EDX have been limited to dehydrated samples. In this state, Ca bilirubinates appear as either glassy masses, which predominate in black pigment stones, or as clusters, which are found mostly in cholesterol gallstones. The three polymorphs of Ca carbonate, calcite, vaterite, and aragonite, have been identified in gallstones by x-ray diffraction, however; the morphologies of these crystals vary in the literature. The purpose of this experiment was to study fresh gallstones by environmental SEM (ESEM) to determine if dehydration affects gallstone Ca salt morphology.Gallstones and bile were obtained fresh at cholecystectomy from 6 patients. To prevent dehydration, stones were stored in bile at 37°C. All samples were studied within 4 days of procurement.

Photocatalytic activity of TiO2 synthesized by anodization and anodic spark deposition

MRS Advances ◽  
2020 ◽  
Vol 5 (61) ◽  
pp. 3141-3152
Author(s):  
Alma C. Chávez-Mejía ◽  
Génesis Villegas-Suárez ◽  
Paloma I. Zaragoza-Sánchez ◽  
Rafael Magaña-López ◽  
Julio C. Morales-Mejía ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Surface Characteristics ◽  
Amorphous Solids ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Activities ◽  
Anodic Spark Oxidation ◽  
Porous Surfaces ◽  
Scanning Electron

AbstractSeveral photocatalysts, based on titanium dioxide, were synthesized by spark anodization techniques and anodic spark oxidation. Photocatalytic activity was determined by methylene blue oxidation and the catalytic activities of the catalysts were evaluated after 70 hours of reaction. Scanning Electron Microscopy and X Ray Diffraction analysis were used to characterize the catalysts. The photocatalyst prepared with a solution of sulfuric acid and 100 V presented the best performance in terms of oxidation of the dye (62%). The electric potential during the synthesis (10 V, low potential; 100 V, high potential) affected the surface characteristics: under low potential, catalyst presented smooth and homogeneous surfaces with spots (high TiO2 concentration) of amorphous solids; under low potential, catalyst presented porous surfaces with crystalline solids homogeneously distributed.

The Effect of the Microstructure of Diffusion Barriers on the Palladium Activation for Electroless Copper Deposition

2002 ◽  
Vol 716 ◽  
Author(s):  
Seok Woo Hong ◽  
Yong Sun Lee ◽  
Ki-Chul Park ◽  
Jong-Wan Park
Keyword(s):  
Electron Microscopy ◽  
Diffusion Barriers ◽  
Copper Deposition ◽  
X Ray Diffraction ◽  
Plan View ◽  
X Ray ◽  
Transmission Electron ◽  
Electroless Copper ◽  
Sheet Resistance Measurement ◽  
Scanning Electron

AbstractThe effect of microstructure of dc magnetron sputtered TiN and TaN diffusion barriers on the palladium activation for autocatalytic electroless copper deposition has been investigated by using X-ray diffraction, sheet resistance measurement, field emission scanning electron microscopy (FE-SEM) and plan view transmission electron microscopy (TEM). The density of palladium nuclei on TaN diffusion barrier increases as the grain size of TaN films decreases, which was caused by increasing nitrogen content in TaN films. Plan view TEM results of TiN and TaN diffusiton barriers showed that palladium nuclei formed mainly on the grain boundaries of the diffusion barriers.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

Structural Characterization of Gallbladder Stones Using Energy Dispersive X-ray Spectroscopy and X-ray Diffraction

2018 ◽  
Vol 21 (7) ◽  
pp. 495-500 ◽  
Author(s):  
Hassan A. Almarshad ◽  
Sayed M. Badawy ◽  
Abdalkarem F. Alsharari
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Energy Dispersive ◽  
Spectroscopic Techniques ◽  
X Ray Diffraction ◽  
Major Health Problem ◽  
X Ray ◽  
Gallbladder Stones ◽  
Pure Cholesterol ◽  
Scanning Electron

Aim and Objective: Formation of the gallbladder stones is a common disease and a major health problem. The present study aimed to identify the structures of the most common types of gallbladder stones using X-ray spectroscopic techniques, which provide information about the process of stone formation. Material and Method: Phase and elemental compositions of pure cholesterol and mixed gallstones removed from gallbladders of patients were studied using energy-dispersive X-ray spectroscopy combined with scanning electron microscopy analysis and X-ray diffraction. Results: The crystal structures of gallstones which coincide with standard patterns were confirmed by X-ray diffraction. Plate-like cholesterol crystals with laminar shaped and thin layered structures were clearly observed for gallstone of pure cholesterol by scanning electron microscopy; it also revealed different morphologies from mixed cholesterol stones. Elemental analysis of pure cholesterol and mixed gallstones using energy-dispersive X-ray spectroscopy confirmed the different formation processes of the different types of gallstones. Conclusion: The method of fast and reliable X-ray spectroscopic techniques has numerous advantages over the traditional chemical analysis and other analytical techniques. The results also revealed that the X-ray spectroscopy technique is a promising technique that can aid in understanding the pathogenesis of gallstone disease.

Sign in / Sign up

Export Citation Format

Share Document