Modeling of Some Related Parameters for Cracking Palm Nut in a Centrifugal Cracker

2013 ◽  
Vol 824 ◽  
pp. 255-261
Author(s):  
Orua O. Antia ◽  
Kessington Obahigbon ◽  
Emmanuel Aluyor ◽  
Patrick Ebunilo
Keyword(s):  
Kinetic Energy ◽  
Experimental Analysis ◽  
Geometric Mean ◽  
Technical Analysis ◽  
Mean Diameter ◽  
Nut Cracking ◽  
The Relationship ◽  
The Revolution

In this study, the principles underlying the energy involved during cracking in a vertical centrifugal nut cracker was analyzed. This will help to elucidate the relationship between various parameters that are relevant to the design and operation of the centrifugal nut cracker for the Tenera and Dura varieties. Experimental analysis was then carried out for each of the two varieties. Each variety was classified into size ranges based on their geometric mean diameter (GMD). Technical analysis revealed that the revolution per minute required by the rotor disc of a centrifugal nut for effective nut cracking is influenced by rotor disc radius (r) and nut dimensions (d1, d2, d3).The modeled equation developed could be used for predicting nut translational kinetic energy required to crack dried nut of the Dura and Tenera varieties to release high percentage of whole kernel.

Analisa Pemilihan Moda Transportasi Umum Rute Tanjung Karang – Bandara Radin Inten II Dengan Stated Preference dan Uji Crame’s V

2018 ◽  
Vol 2 (2) ◽  
pp. 137
Author(s):  
Muhammad Abi Berkah Nadi
Keyword(s):  
Regression Analysis ◽  
Utility Function ◽  
Stated Preference ◽  
Technical Analysis ◽  
Chi Square ◽  
Time Headway ◽  
Independent Variable ◽  
The Relationship ◽  
Selection Of

Radin Inten II Airport is a national flight in Lampung Province. In this study using the technical analysis stated preference which is the approach by conveying the choice statement in the form of hypotheses to be assessed by the respondent. By using these techniques the researcher can fully control the hypothesized factors. To determine utility function for model forecasting in fulfilling request of traveler is used regression analysis with SPSS program. The analysis results obtained that the passengers of the dominant airport in the selection of modes of cost attributes than on other attributes. From the result of regression analysis, the influence of independent variable to the highest dependent variable is when the five attributes are used together with the R square value of 8.8%. The relationship between cost, time, headway, time acces and service with the selection of modes, the provision that states whether or not there is a decision. The significance of α = 0.05 with chi-square. And the result of Crame's V test average of 0.298 is around the middle, then the relationship is moderate enough.

The relationship between health effects in triathletes and microbiological quality of freshwater

1995 ◽  
Vol 31 (5-6) ◽  
pp. 19-26 ◽  
Author(s):  
G. J. Medema ◽  
I. A. van Asperen ◽  
J. M. Klokman-Houweling ◽  
A. Nooitgedagt ◽  
M. J. W. van de Laar ◽  
...  
Keyword(s):  
Water Quality ◽  
Geometric Mean ◽  
Microbiological Quality ◽  
Quality Parameters ◽  
Health Complaints ◽  
E Coli ◽  
Thermotolerant Coliforms ◽  
Microbiological Water Quality ◽  
The Relationship ◽  
Faecal Streptococci

This pilot study was carried out to determine the relationship between microbiological water quality parameters and the occurrence of health complaints among triathletes. Data were collected at an Olympic distance triathlon (n=314) and a run-bike-run (n=81; controls for exposure to fresh water). At the time of the triathlon, the concentrations of Escherichia coli , thermotolerant coliforms, faecal streptococci, entero- and reoviruses, F-specific RNA phages, Salmonella, Campylobacter, Aeromonas, Plesiomonas shigelloides, Pseudomonas aeruginosa and Staphylococcus aureus were examined over the swimming course. Information on the occurrence of health complaints during the competition and in the week thereafter was collected through a written questionnaire. The results show that triathletes and run-bike-runners are comparable with respect to factors other than water exposure (age, sex, training history, physical stress, lower intestinal health complaints during the competition) that may influence the occurrence of health complaints in the week after the competition. Triathletes and run-bike-runners reported gastro-intestinal (7.7% vs 2.5%), respiratory (5.5% vs 3.7%), skin/mucosal (2.6% vs 1.2%), general (3.5% vs 1.2%) and total symptoms (14.8% vs 7.4%) in the week after the event. The health risks for triathletes for all symptom groups are not significantly higher than for run-bike-runners. The geometric mean concentration of faecal indicator bacteria is relatively low: E. coli 170/100 ml; faecal streptococci 13/100 ml, enteroviruses were present at concentrations of 0.1/l. The group of triathletes was homogeneusly and relatively intensely exposed to water; they all swam in the same body of water at the same time and 75% reported to have swallowed freshwater. It was concluded that this study design is suitable to study the relationship between health complaints and microbiological water quality. In the summers of 1993 and 1994, a study will be carried out concerning several run-bike-runs and triathlons in freshwaters of different quality.

Consistent Theoretical Model of Mean Diameter and Size Distribution by Liquid Sheet Atomization

2012 ◽  
Author(s):  
Chihiro Inoue ◽  
Toshinori Watanabe ◽  
Takehiro Himeno ◽  
Seiji Uzawa ◽  
Mitsuo Koshi
Keyword(s):  
Theoretical Model ◽  
Kinetic Energy ◽  
Droplet Diameter ◽  
Velocity Profiles ◽  
Liquid Sheet ◽  
Estimation Methods ◽  
Liquid Jets ◽  
Injection Velocity ◽  
Size Distributions ◽  
Mean Diameter

A consistent theoretical model is proposed and validated for calculating droplet diameters and size distributions. The model is derived based on the energy conservation law including the surface free energy and the Laplace pressure. Under several hypotheses, the law derives an equation indicating that atomization results from kinetic energy loss. Thus, once the amount of loss is determined, the droplet diameter is able to be calculated without the use of experimental parameters. When the effects of ambient gas are negligible, injection velocity profiles of liquid jets are the essential cause of the reduction of kinetic energy. The minimum Sauter mean diameter produced by liquid sheet atomization is inversely proportional to the injection Weber number when the injection velocity profiles are laminar or turbulent. A non-dimensional distribution function is also derived from the mean diameter model and Nukiyama-Tanasawa’s function. The new estimation methods are favorably validated by comparing with corresponding mean diameters and the size distributions, which are experimentally measured under atmospheric pressure.

scholarly journals Kinetic energy entrainment in wind turbine and actuator disc wakes: an experimental analysis

2014 ◽  
Vol 524 ◽  
pp. 012163 ◽  
Author(s):  
L E M Lignarolo ◽  
D Ragni ◽  
C J Simão Ferreira ◽  
G J W van Bussel
Keyword(s):  
Kinetic Energy ◽  
Wind Turbine ◽  
Experimental Analysis ◽  
Actuator Disc

scholarly journals Overview of a prescribed burning experiment within a boreal forest in Finland

2013 ◽  
Vol 13 (8) ◽  
pp. 21703-21763 ◽  
Author(s):  
A. Virkkula ◽  
J. Levula ◽  
T. Pohja ◽  
P. P. Aalto ◽  
P. Keronen ◽  
...  
Keyword(s):  
Boreal Forest ◽  
Radiative Forcing ◽  
Prescribed Burning ◽  
Geometric Mean ◽  
Sonic Anemometer ◽  
Ground Level ◽  
Organic Layer ◽  
Available Nitrogen ◽  
Mean Diameter

Abstract. A prescribed burning of a boreal forest was conducted on 26 June 2009 in Hyytiälä, Finland, to study aerosol and trace gas emissions from wildfires and the effects of fire on soil properties in a controlled environment. A 0.8 ha forest near the SMEAR II was cut clear; some tree trunks, all tree tops and branches were left on the ground and burned. The amount of burned organic material was ~46.8 t (i.e., ~60 t ha−1). The flaming phase lasted 2 h 15 min, the smoldering phase 3 h. Measurements were conducted on the ground with both fixed and mobile instrumentation, and from a research aircraft. In the middle of the burning area, CO2 concentration peaks were around 2000–3000 ppm above the baseline and peak vertical flow velocities were 6 ± 3 m s−1, as measured a 10-Hz 3-D sonic anemometer placed within the burn area. Peak particle number concentrations were approximately 1–2 × 106 cm−3 in the plume at a distance of 100–200 m from the burn area. The geometric mean diameter of the mode with the highest concentration was at 80 ± 1 nm during the flaming phase and in the middle of the smoldering phase but at the end of the smoldering phase the largest mode was at 122 nm. In the volume size distributions geometric mean diameter of the largest volume mode was at 153 nm during the flaming phase and at 300 nm during the smoldering phase. The lowest single-scattering albedo of the ground-level measurents was 0.7 in the flaming-phase plume and ~0.9 in the smoldering phase. The radiative forcing efficiency was negative above dark surfaces, in other words, the particles cool the atmosphere. Elevated concentrations of several VOCs (including acetonitrile which is a biomass burning marker) were observed in the smoke plume at ground level. The forest floor (i.e., richly organic layer of soil and debris, characteristic of forested land) measurements showed that VOC fluxes were generally low and consisted mainly of monoterpenes, but a clear peak of VOC flux was observed after the burning. After one year, the fluxes were nearly stabilised close to the level before the burning. The clearcutting and burning of slash increased the total long-term CO2 release from the soil, altered the soil's physical, chemical and biological properties such as increased the available nitrogen contents of the soil, which in turn, affected the level of the long-term fluxes of greenhouse gases.

scholarly journals EARNINGS ANNOUNCEMENTS AND COMPETING INFORMATION: THE INDONESIAN EVIDENCE

2015 ◽  
Vol 29 (1) ◽  
Author(s):  
Dedhy Sulistiawan ◽  
Jogiyanto Hartono ◽  
Eduardus Tandelilin ◽  
Supriyadi Supriyadi
Keyword(s):  
Stock Market ◽  
Empirical Evidence ◽  
Earnings Announcements ◽  
Negative Relationship ◽  
Technical Analysis ◽  
Earnings Announcement ◽  
Price Reaction ◽  
Price Reactions ◽  
The Relationship ◽  
The U.S

The main purpose of this study is to provide empirical evidence of the relationship betweeninvestors’ responses to two events, which are, (1) earnings anouncements, and (2) technicalanalysis signals, as competing information. This study is motivated by Francis, et al. (2002),whose study used stock analyst’s recommendations as competing information in the U.S stockmarket. To extend that idea, this study uses technical analysis signals as competing informationin the Indonesian stock market. Using Indonesian data from 2007-2012, this study shows thatthere are price reactions on the day of a technical analysis signal’s release, which is prior toearnings announcements. It means that investors react to the emergence of competinginformation. Reactions on earnings announcements also produce a negative relationship withthe reaction to a technical analysis signal before an earnings announcement. This study givesevidence about the importance of technical analysis as competing information to earningsannouncements.Keywords: competing information, earnings announcements, technical analysis, price reaction

scholarly journals Subthreshold swing model using scale length for sub-10 nm junction-based double-gate MOSFETs

2020 ◽  
Vol 10 (2) ◽  
pp. 1747
Author(s):  
Hakkee Jung
Keyword(s):  
Analytical Model ◽  
Potential Distribution ◽  
Geometric Mean ◽  
Oxide Thickness ◽  
Channel Length ◽  
Subthreshold Swing ◽  
Double Gate ◽  
Silicon Thickness ◽  
The Relationship ◽  
Scale Length

We propose an analytical model for subthreshold swing using scale length for sub-10 nm double gate (DG) MOSFETs. When the order of the calculation for the series type potential distribution is increased it is possible to obtain accuracy, but there is a problem that the calculation becomes large. Using only the first order calculation of potential distribution, we derive the scale length λ1 and use it to obtain an analytical model of subthreshold swing. The findings show this subthreshold swing model is in concordance with a 2D simulation. The relationship between the channel length and silicon thickness, which can analyze the subthreshold swing using λ1, is derived by the relationship between the scale length and the geometric mean of the silicon and oxide thickness. If the silicon thickness and oxide film thickness satisfy the condition of (Lg-0.215)/6.38 > tsi(=tox), it is found that the result of this model agrees with the results using higher order calculations, within a 4% error range.

scholarly journals Assessment of Physical, Microstructural, Thermal, Techno-Functional, And Rheological Characteristics of Apple (Malus Domestica) Seeds of Northern Himalayas

2021 ◽  
Author(s):  
Mehnaza Manzoor ◽  
Jagmohan Singh
Keyword(s):  
Energy Requirement ◽  
Geometric Mean ◽  
High Energy ◽  
Particle Size Analysis ◽  
Absorption Capacity ◽  
Size Analysis ◽  
Scanning Electron Micrographs ◽  
Seed Flour ◽  
Mean Diameter ◽  
Golden Delicious

Abstract The study examined the physical, morphological, thermal, techno-functional, and rheological properties of two apple seed cultivars viz: red delicious (RD) and golden delicious (GD). Physical properties showed that red delicious seeds were significantly (p≤0.05) different in width, geometric mean diameter, arithmetic mean diameter, volume, and surface area than golden delicious seeds. The proximate composition of RD seed flour showed a higher amount of crude protein and fat content than GD seed flour. RD seed flour was significantly different in L*, a*, b* values, bulk density, water/oil absorption capacity and the emulsifying ability than GD seed flour. From particle size analysis it was possible to found that GD was significantly (p≤0.05) lower than RD flour macromolecules. Scanning electron micrographs showed oval/spherical starch granules of small size embedded in a continuous protein matrix. Thermograph revealed exothermic transition enthalpy for both RD and GD seed flour, which indicates a high energy requirement for crystallite melting. The rheological assays revealed high elastic modulus (G′), of seed flours that will help in modifying the texture of foods. This study suggests the potential of apple seeds in the formulation of protein-enriched foods to combat malnutrition while contributing to the reduction in industrial wastage.

Sign in / Sign up

Export Citation Format

Share Document