The Effect of Cutting Speed on the Machinability of 2080 Special K Steel on Vertical Machining Center

2014 ◽  
Vol 875-877 ◽  
pp. 1406-1411
Author(s):  
Abdullah Altın
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cold Work ◽  
Cutting Speed ◽  
Milling Process ◽  
Depth Of Cut ◽  
Workpiece Material ◽  
Machining Center ◽  
Cutting Speeds

This study presents the results of machining tests carried out determine the effect of cutting forces and surface roughness on machininig of 2080 Special K (1.2080 DINX210Cr12) cold work steel in terms of cutting speed, feed rate and depth of cut for milling process. A series of experiments have been performed on 2080 Special K steel material of cutting width 50 mm with round uncoated cemented carbide insert on 5,5 Kw engine power Jhonford VMC550 CNC vertical machining center without cutting fluid. Experiments were carried out by using four different cutting speeds (70,90,110,130 m/min) at constant depth of cut (1mm) and feed rate (0,3mm/rev.) and the effects of cutting speeds on primary cutting force and surface roughness were investigated. The study of the influence of workpiece material on milling process shows that hardening of material increased by machining up. Cutting force (Fc) and surface roughness decreases with improving workpiece material machinability. From the experiments, the lowest average primary cutting force was obtained as 604,03N at cutting speed of 90m/min. The lowest average surface roughness has been obtained as 0,19 um at cutting speed 110m/min. Obtained chip form is narrow and short step.

Effect of Tool Edge Geometry on Cutting Force and Surface Roughness when Hard Turning Tool Steel

2012 ◽  
Vol 505 ◽  
pp. 15-19 ◽  
Author(s):  
Mohd Yusof Noordin ◽  
Ali Davoudinejad ◽  
Mohd Rosmaini Shaari
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Tangential Force ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Workpiece Material ◽  
Edge Preparation

High usage of hardened steel in the automotive, gear, bearing, tool and die making industries, makes it a highly suitable material for industrial production and research. This study was undertaken to investigate the performance of coated ceramic insert with different edge preparations in terms of cutting force and surface roughness. Plain turning experiments were carried out under dry cutting condition at two different cutting speeds and feed rates with a constant depth of cut. The workpiece material is ASSAB DF-3 hardened steel with a 55 ±1 HRC hardness. Results showed that insert edge preparation had a direct influence on the radial and feed forces but not on the tangential force. The use of T-land edge preparation results in the lowest radial and feed forces. In terms of surface finish, the use of honed with finishing wiper insert results in obtaining the lowest surface roughness values. Feed rate had a significant effect on surface roughness whereby by increasing feed rate, the surface roughness value also increased, whereas the effect of cutting speed was found to be insignificant. Increasing cutting speed resulted in lower feed and tangential forces however by increasing feed rate all cutting forces increased.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

scholarly journals Analysis of tool wear and surface roughness in high-speed milling process of aluminum alloy Al6061

2021 ◽  
pp. 71-84
Author(s):  
Nhu-Tung Nguyen ◽  
Dung Hoang Tien ◽  
Nguyen Tien Tung ◽  
Nguyen Duc Luan
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Tool Wear ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Milling Process ◽  
Face Milling ◽  
Depth Of Cut ◽  
High Speed Milling

In this study, the influence of cutting parameters and machining time on the tool wear and surface roughness was investigated in high-speed milling process of Al6061 using face carbide inserts. Taguchi experimental matrix (L9) was chosen to design and conduct the experimental research with three input parameters (feed rate, cutting speed, and axial depth of cut). Tool wear (VB) and surface roughness (Ra) after different machining strokes (after 10, 30, and 50 machining strokes) were selected as the output parameters. In almost cases of high-speed face milling process, the most significant factor that influenced on the tool wear was cutting speed (84.94 % after 10 machining strokes, 52.13 % after 30 machining strokes, and 68.58 % after 50 machining strokes), and the most significant factors that influenced on the surface roughness were depth of cut and feed rate (70.54 % after 10 machining strokes, 43.28 % after 30 machining strokes, and 30.97 % after 50 machining strokes for depth of cut. And 22.01 % after 10 machining strokes, 44.39 % after 30 machining strokes, and 66.58 % after 50 machining strokes for feed rate). Linear regression was the most suitable regression of VB and Ra with the determination coefficients (R2) from 88.00 % to 91.99 % for VB, and from 90.24 % to 96.84 % for Ra. These regression models were successfully verified by comparison between predicted and measured results of VB and Ra. Besides, the relationship of VB, Ra, and different machining strokes was also investigated and evaluated. Tool wear, surface roughness models, and their relationship that were found in this study can be used to improve the surface quality and reduce the tool wear in the high-speed face milling of aluminum alloy Al6061

scholarly journals Analysis and Optimization of Cutting Tool Coating Effects on Surface Roughness and Cutting Forces on Turning of AA 6061 Alloy

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Mahir Akgün ◽  
Fuat Kara
Keyword(s):  
Surface Roughness ◽  
Mathematical Models ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Cutting ◽  
Machined Surface ◽  
Tool Coating ◽  
Cutting Inserts

The present work has been focused on cutting force (Fc) and analysis of machined surface in turning of AA 6061 alloy with uncoated and PVD-TiB2 coated cutting inserts. Turning tests have been conducted on a CNC turning under dry cutting conditions based on Taguchi L18 (21 × 33) array. Kistler 9257A type dynamometer and equipment have been used in measuring the main cutting force (Fc) in turning experiments. Analysis of variance (ANOVA) has been applied to define the effect levels of the turning parameters on Fc and Ra. Moreover, the mathematical models for Fc and Ra have been developed via linear and quadratic regression models. The results indicated that the best performance in terms of Fc and Ra was obtained at an uncoated insert, cutting speed of 350 m/min, feed rate of 0.1 mm/rev, and depth of cut of 1 mm. Moreover, the feed rate is the most influential parameter on Ra and Fc, with 64.28% and 54.9%, respectively. The developed mathematical models for cutting force (Fc) and surface roughness (Ra) present reliable results with coefficients of determination (R2) of 96.04% and 92.15%, respectively.

Experimental Investigations of Cutting Conditions Influence on Main Cutting Force and Surface Roughness Based on Chip Form Types in Cast Nylon Turning

2011 ◽  
Vol 110-116 ◽  
pp. 3563-3569 ◽  
Author(s):  
Bandit Suksawat
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Causal Effect ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Path Coefficient ◽  
Cutting Depth

This paper aims to investigate cutting conditions influence on main cutting force and surface roughness based on considered chip form types in cast nylon turning operation with single-point high speed steel cutting tool. The 75 experiments were performed by average of three levels of cutting speed, five levels of cutting depth and five levels of feed rate. The results reveal that main cutting forces were increased by an increasing of cutting speed and cutting depth for all obtained chip form types for all chip form types. The surface roughness is affected by increasing of feed rate and reduction of cutting speed for 2.3 Snarled and 4.3 Snarled chip form types. The statistical path-coefficient analysis results are shown that the main cutting force affected by cutting speed, depth of cut and feed rate with total causal effect value of 0.5537, 0.4785 and 0.1718, respectively. The surface roughness is influenced by feed rate, cutting speed and depth of cut with 0.8400, -0.2419 and-0.0711 of total causal effect value, respectively. These results are useful to perform varying cutting conditions for high quality of workpiece in cast nylon turning by control the chip form type.

Monitoring of Surface Roughness Based on Cutting Force and Cutting Temperature in Ball-End Milling Process by Utilizing Response Surface Analysis

2015 ◽  
Vol 799-800 ◽  
pp. 324-328
Author(s):  
Panrawee Yaisuk ◽  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Response Surface ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Temperature ◽  
Milling Process ◽  
Depth Of Cut ◽  
Tool Diameter ◽  
End Milling Process

The surface roughness is monitored using the cutting force and the cutting temperature in the ball-end milling process by utilizing the response surface analysis with the Box-Behnken design. The optimum cutting condition is obtained referring to the minimum surface roughness, which is the spindle speed, the feed rate, the depth of cut, and the tool diameter. The models of cutting force ratio and the cutting temperature are proposed and developed based on the experimental results. It is understood that the surface roughness is improved with an increase in spindle speed, feed rate and depth of cut. The cutting temperature decreases with an increase in tool diameter. The model verification has showed that the experimentally obtained surface roughness model is reliable and accurate to estimate the surface roughness.

An Experimental Study on Finish Dry Milling of AISI 321 Stainless Steel

2016 ◽  
Vol 861 ◽  
pp. 26-31 ◽  
Author(s):  
Peng Guo ◽  
Chuan Zhen Huang ◽  
Bin Zou ◽  
Jun Wang ◽  
Han Lian Liu ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Tool Wear ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Dry Milling ◽  
Aisi 321 ◽  
Coated Cemented Carbide

The milling of AISI 321 stainless steel which has wide engineering applications particularly in automobile, aerospace and medicine is of great importance especially in the conditions where high surface quality is required. In this paper, L16 orthogonal array design of experiments was adopted to evaluate the machinability of AISI 321 stainless steel with coated cemented carbide tools under finish dry milling conditions, and the influence of cutting speed ( V ), feed rate ( f ) and depth of cut ( ap ) on cutting force, surface roughness and tool wear was analysed. The experimental results revealed that the cutting force decreased with an increase in the cutting speed and increased with an increase in the feed rate or the depth of cut. The tool wear was affected significantly by the cutting speed and the depth of cut, while the effect of the feed rate on the tool wear was insignificant. With the cutting speed increased up to 160 m/min, a decreasing tendency in the surface roughness was observed, but when the cutting speed was further increased, the surface roughness increased. The effect of the feed rate and the depth of cut on the surface roughness was slight.

scholarly journals Prediction of surface roughness and cutting force under MQL turning of AISI 4340 with nano fluid by using response surface methodology

2018 ◽  
Vol 5 ◽  
pp. 5 ◽  
Author(s):  
Pralhad B. Patole ◽  
Vivek V. Kulkarni
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Cutting Force ◽  
Response Surface ◽  
Process Parameters ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Nano Fluid ◽  
Aisi 4340

This paper presents an investigation into the minimum quantity lubrication mode with nano fluid during turning of alloy steel AISI 4340 work piece material with the objective of experimental model in order to predict surface roughness and cutting force and analyze effect of process parameters on machinability. Full factorial design matrix was used for experimental plan. According to design of experiment surface roughness and cutting force were measured. The relationship between the response variables and the process parameters is determined through the response surface methodology, using a quadratic regression model. Results show how much surface roughness is mainly influenced by feed rate and cutting speed. The depth of cut exhibits maximum influence on cutting force components as compared to the feed rate and cutting speed. The values predicted from the model and experimental values are very close to each other.

Evaluation of Face Milling Operation Parameters on Surface Roughness of Crankcase Housing by Two Level Factorial Design with Center Points

2018 ◽  
Vol 780 ◽  
pp. 105-110
Author(s):  
Ukrit Thanasuptawee ◽  
Chamrat Thakhamwang ◽  
Somsak Siwadamrongpong
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Milling Process ◽  
Face Milling ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Significance Level ◽  
Machining Center ◽  
Semi Solid

In this study, there are three machining parameters consist of spindle speed, feed rate and depth of cut which were conducted through full factorial with four center points to determine the effect of machining parameters on the surface roughness and verify whether there is curvature in the model for CNC face milling process in an automotive components manufacturer in Thailand. The workpieces used semi-solid die casted ADC12 aluminum alloy crankcase housing which they were performed by the ARES SEIKI model R5630 3-axis CNC vertical machining center and face milling cutter with diameter of 63 millimeters. The surface roughness of face-milled was measured by the surface roughness tester. It was found that the greatest main effect influence to surface roughness was spindle speed, followed by feed rate and depth of cut at significance level of 0.05.

Sign in / Sign up

Export Citation Format

Share Document