Preparation and Characterization of Unsaturated Polyester/Organic Montmorillonite Nanocomposites

2014 ◽  
Vol 875-877 ◽  
pp. 150-154 ◽  
Author(s):  
Tsung Yen Tsai ◽  
Wen Chi Chen ◽  
Guan Ren Zhou ◽  
Wei Chuan Shiu
Keyword(s):  
Thermal Properties ◽  
In Situ Polymerization ◽  
Unsaturated Polyester ◽  
Gravimetric Analysis ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
Limiting Oxygen Index ◽  
X Ray ◽  
Modified Clay

This study uses in-situ polymerization method due to organic modified montmorillonite into unsaturated polyester to form a advanced montmorillonite / unsaturated polyester (MMT /UP) nanocomposites. Using of the blasting force generated in situ polymerization patterns show the formation of clay layers is exfoliation structure in polymer and improving of thermal properties, flame retardant properties, and mechanical properties.The d-spacing of organic modified clay could be determined whether the modifier was intercalated into the gallery of clay by applying the wide-angle X-ray diffraction (WXRD). The functional groups of modified clay were measured by Fourier infrared spectroscopy (FT-IR). The dispersion morphologies of MMT / UP nanocomposites were characterized by the wide-angle X-ray diffraction (WXRD) and transmission electron microscopy (TEM). The thermal properties and mechanical properties were investigated by thermal gravimetric analysis (TGA), limiting oxygen index meter (LOI), cone calorimeter (Heat Release Rate) and a dynamic mechanical analyzer (DMA).

MECHANICAL AND THERMAL PROPERTIES OF MONTMORILLONITE-EPOXY NANOCOMPOSITE

2008 ◽  
Vol 22 (18n19) ◽  
pp. 3247-3253 ◽  
Author(s):  
B. T. MAROUF ◽  
R. BAGHERI ◽  
R. A. PEARSON
Keyword(s):  
Thermal Properties ◽  
In Situ Polymerization ◽  
Mechanical And Thermal Properties ◽  
Toughening Mechanism ◽  
X Ray Diffraction ◽  
X Ray ◽  
Epoxy Nanocomposite ◽  
Transmission Electron ◽  
Stiffening Effect

In this investigation, the mechanical and thermal properties of the montmorillonite-epoxy nanocomposites were studied. The epoxy compounds were prepared by in situ polymerization and the intercalation dispersion were obtained as evidenced using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results reveal remarkable stiffening effect and slight toughening effect of the MMT in the epoxy resin and an insight about the crack tip and notch tip toughening mechanism. According to the DMA, the glass transition temperature increases as increasing the MMT content.

Structure and properties of PA6-66/γ-aminopropyltriethoxysilane-modified clay nanocomposites prepared by in situ polymerization

2018 ◽  
Vol 39 (1) ◽  
pp. 16-24 ◽  
Author(s):  
Xiaochao Liu ◽  
Dengwang Lai ◽  
Yuejun Liu ◽  
Pu Shi ◽  
Wenzhi Wang ◽  
...  
Keyword(s):  
Mechanical Performance ◽  
In Situ Polymerization ◽  
Covalent Bond ◽  
Polymer Chains ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Modified Clay ◽  
Transmission Electron

AbstractIn this study, PA6-66/γ-aminopropyltriethoxysilane-modified clay nanocomposites were prepared byin situpolymerization. It was found that the γ-aminopropyltriethoxysilane was chemically grafted onto clay successfully, and the covalent bond was formed between the clay and polymer chains. The transmission electron microscopy (TEM) and X-ray diffraction (XRD) results indicated that intercalated and exfoliated nanocomposites were obtained. The PA6-66 nanocomposites exhibited improved mechanical performance compared to that of neat PA6-66. Most importantly, the PA6-66 nanocomposites showed significantly improved toughness. In comparison with neat PA6-66, the rupture stress and elongation at the break of the nanocomposite with only 0.5 wt% clay increased 91.9% and 91.8%, respectively. The excellent toughness of PA6-66 nanocomposites should be mainly ascribed to the combined effects of strong polymer-clay interaction, the intercalated-exfoliated structures of clay, refined crystalline, formation of γ-form crystals, and decreased crystallinity of PA6-66.

In situ time resolved wide angle X-ray diffraction study of nanotube carpet growth: Nature of catalyst particles and progressive nanotube alignment

Carbon ◽  
2015 ◽  
Vol 87 ◽  
pp. 246-256 ◽  
Author(s):  
Périne Landois ◽  
Mathieu Pinault ◽  
Stéphan Rouzière ◽  
Dominique Porterat ◽  
Cristian Mocuta ◽  
...  
Keyword(s):  
Diffraction Study ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
Time Resolved ◽  
X Ray

Synthesis and Characterization of the PANI/ITO Conducting Nanocomposites

2010 ◽  
Vol 663-665 ◽  
pp. 542-545 ◽  
Author(s):  
Bing Jie Zhu ◽  
Xin Wei Wang ◽  
Mei Fang Zhu ◽  
Qing Hong Zhang ◽  
Yao Gang Li ◽  
...  
Keyword(s):  
Doping Concentration ◽  
In Situ Polymerization ◽  
Synthesis And Characterization ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Conductivity ◽  
Scanning Electron

The PANI/ITO conducting nanocomposites have been synthesized by in-situ polymerization. The obtained nanocomposites were characterized by X-ray diffraction pattern, scanning electron microscopy and Fourier transform infrared. Electrical conductivity measurements on the samples pressed into pellets showed that the maximum conductivity attained 2.0 ± 0.05 S/cm for PANI/ITO nanocomposites, at ITO doping concentration of 10 wt%. The results of the present work may provide a simple, rapid and efficient approach for preparing PANI/ITO nanocomposites.

Morphology of Polyethylene/Montmorillonite Nanocomposites Prepared by In Situ Polymerization

2013 ◽  
Vol 457-458 ◽  
pp. 244-247
Author(s):  
Min Li ◽  
Li Guang Xiao ◽  
Hong Kai Zhao
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reflection Peak ◽  
Basal Reflection ◽  
Scanning Electron

Polyethylene/montmorillonite (PE/MMT) nanocomposites were prepared by in situ polymerization. The morphology of MMT/MgCl2/TiCl4 catalyst and PE/MMT nanocomposites was investigated by scanning electron microscopy (SEM). It can be seen that MMT/MgCl2/TiCl4 catalyst remained the original MMT sheet structures and many holes were found in MMT and the morphology of PE/MMT nanocomposites is part of the sheet in the form of existence, as most of the petal structure. X-ray diffraction (XRD) and transmission electron microscopy (TEM) were carried out to characterize all the samples. XRD results reveal that the original basal reflection peak of PEI1 and PEI2 disappears completely and that of PEI3 become very weak. MMT/MgCl2/TiCl4 catalyst was finely dispersed in the PE matrix. Instead of being individually dispersed, most layers were found in thin stacks comprising several swollen layers.

Evolution of Carbon Fiber Microstructure During Carbonization and High-Temperature Graphitization Measured In Situ Using Synchrotron Wide-Angle X-ray Diffraction

2015 ◽  
Vol 1754 ◽  
pp. 13-18 ◽  
Author(s):  
Michael Behr ◽  
James Rix ◽  
Brian Landes ◽  
Bryan Barton ◽  
Eric Hukkanen ◽  
...  
Keyword(s):  
High Temperature ◽  
Carbon Fiber ◽  
Tensile Modulus ◽  
Fiber Bundles ◽  
Wide Angle ◽  
High Modulus ◽  
Structure Property ◽  
X Ray Diffraction ◽  
X Ray

ABSTRACTThis paper will discuss the structure-property model developed that correlates the tensile modulus to the elastic properties and angular distribution of constituent graphitic layers for carbon fiber derived from a polyethylene precursor. In addition, a high-temperature fiber tensile device was built to enable heating of carbon fiber bundles at a variable rate from 25 °C to greater than ∼2300 °C, while simultaneously applying a tensile stress. This capability combined with synchrotron wide-angle x-ray diffraction (WAXD), enabled observation in situ and in real time of the microstructural transformation from different carbon fiber precursors to high-modulus carbon fiber. Experiments conducted using PAN- and PE-derived fiber precursors reveal stark differences in their carbonization and high-temperature graphitization behavior.

Synthesis and Electrorheological Characteristics of Conducting Polymer/Clay Nanocomposites

2007 ◽  
Vol 124-126 ◽  
pp. 1083-1086
Author(s):  
Jun Hee Sung ◽  
Hyoung Jin Choi
Keyword(s):  
Conducting Polymer ◽  
Electrorheological Fluid ◽  
Clay Nanocomposites ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Internal Structures ◽  
In Situ Emulsion Polymerization

Nanocomposites of conducting polymers of polyaniline (PANI), poly(oethoxyaniline) (PEOA) and polypyrrole (PPy) with clay prepared via either in-situ emulsion polymerization or solvent intercalation were investigated especially for electrorheological fluid (ER) application. Internal structures of these nanocomposites were examined via wide angle X-ray diffraction (WAXD), and transmission electron microscope (TEM). The intercalated nanostructures analyzed via WAXD and TEM were correlated with the electrical property change originated from the nanoscale interaction between clay and conducting polymer. Moreover, their ER behaviors were measured via rotational rheometer with external electric field controller.

MECHANICAL PROPERTIES OF A POLYURETHANE/MONTMORILLONITE NANOCOMPOSITE FEATURING ORGANOMODIFICATION SYNTHESIZED VIA IN SITU POLYMERIZATION

2015 ◽  
Vol 88 (1) ◽  
pp. 138-146 ◽  
Author(s):  
Rouhollah Bagheri ◽  
Reza Darvishi
Keyword(s):  
Mechanical Properties ◽  
In Situ Polymerization ◽  
Xrd Analysis ◽  
Silicate Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
End Groups ◽  
Layer Sample ◽  
Silicate Layers

ABSTRACT In this study, polyurethane (PU)/organomodified montmorillonite (cloisite®30B) is synthesized via in situ polymerization by reaction of an ether-based prepolymer with the isocyanate end groups and adiamine chain extender (4, 4-methylene-bis(2-chloroaniline)) in the presence of different amounts of nanoparticles dispersed in the prepolymer matrix by an ultrasonic mixer for 1 h. The synthesized polymers are cast on a pretreated carbon steel sheet and cured at 120 °C in an oven. The PU and its composites have been characterized by using Fourier transform infrared spectroscopy, X-ray diffraction (XRD), and mechanical testing. The XRD analysis of the cured samples containing 1 to 3 wt% cloisite30B showed intercalation segments in the silicate layers and exfoliation for 0.5 wt% nanoparticles. The highest mechanical properties were obtained using the cured exfoliated silicate layer sample. A twofold increase in the ultimate tensile strength and a 2.3 times increase in the adhesion strength were found for 0.5 wt% organoclay/PU as compared with that of pure PU. In addition, the exfoliated structure sample exhibited a 16% reduction in abrasion compared with that of pure PU.

Sign in / Sign up

Export Citation Format

Share Document