CoPc/CdS Hybrid Photovoltaic Device

2010 ◽  
Vol 93-94 ◽  
pp. 570-573 ◽  
Author(s):  
P. Keeratithivakorn ◽  
B. Tunhoo ◽  
T. Thiwawong ◽  
J. Nukeaw
Keyword(s):  
Power Conversion Efficiency ◽  
Layer Thickness ◽  
Conversion Efficiency ◽  
Short Circuit ◽  
Power Conversion ◽  
Cadmium Sulphide ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Organic Layer ◽  
Photovoltaic Properties

The organic-inorganic hybrid photovoltaic (PV) cells based on cadmium sulphide (CdS) and cobalt phthalocyanine (CoPc) films have been fabricated and characterized their PV performance. This investigated the effects of the organic and inorganic layer thickness on the photovoltaic properties, these thickness was controlled at various values such as 10, 30 and 50 nm. However, the performance of the hybrid photovoltaic cells was depending on the organic layer thickness. The optimize results of PV cell with CoPc 10 nm and CdS 30 nm showed an open-circuit voltage (Voc) = 0.536 V, a short-circuit current density (Jsc) = 0.1020 mA/cm2, a fill factor FF = 0.281 and a power conversion efficiency (η) = 0.01536 % under the AM1.5 conditions. Efficiency is enhanced by 22 times with the addition of a buffer layer, bathocuproine (BCP) 5 nm, the power conversion efficiency (η) value from 0.01536 to 0.34571%.

Effect of temperature on organic Schottky barrier cells

1981 ◽  
Vol 59 (6) ◽  
pp. 727-732 ◽  
Author(s):  
Rafik O. Loutfy ◽  
Cheng-Kuo Hsiao
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Schottky Barrier ◽  
Conversion Efficiency ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Power Conversion ◽  
Open Circuit ◽  
Effect Of Temperature ◽  
Photovoltaic Properties

The effect of temperature on the photovoltaic properties of indium/metal-free phthalocyanine Schottky barrier solar cells was investigated in the range 260–350 K. In general, the short circuit photocurrent, Jsc, and fill factor, ff, increased with increasing temperature (in contrast to inorganic photocells). The device series resistance and open circuit photovoltage, Voc, decreased (similar to inorganic photocells) as temperature was raised. An increase in the overall power conversion efficiency, η, has been observed with increase of temperature. In the case of x-H2Pc, the power conversion efficiency increased by 2.5 times due to a temperature rise of 60 °C above ambient. Thus, for operation at temperatures above ambient, organic solar cells may offer a significant advantage over inorganic cells.Analysis of the variation of the photovoltage with temperature showed that the decrease in Voc is mainly due to variation injunction impedance, which is controlled by thermionic current at high temperature and ionized impurity at low temperature.

scholarly journals Donor-Acceptor Polymer Based on Planar Structure of Alkylidene-Fluorene Derivative: Correlation of Power Conversion Efficiency among Polymer and Various Acceptor Units

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2859
Author(s):  
Eui Jin Lee ◽  
Ho Jun Song
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Short Circuit ◽  
Power Conversion ◽  
Average Molecular Weight ◽  
Coupling Reaction ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Planar Structure ◽  
Quinoxaline Derivatives

This study synthesized a novel polymer, poly(alkylidene fluorene-alt-diphenylquinoxaline) (PAFDQ), based on a planar alkylidene-fluorene and a highly soluble quinoxaline derivative through the Suzuki coupling reaction. We designed a novel molecular structure based on alkylidene fluorene and quinoxaline derivatives due to compact packing property by the planar structure of alkyidene fluorene and efficient intra-molecular charge transfer by quinoxaline derivatives. The polymer was largely dissolved in organic solvents, with a number average molecular weight and polydispersity index of 13.2 kg/mol and 2.74, respectively. PAFDQ showed higher thermal stability compared with the general fluorene structure owing to its rigid alkylidene-fluorene structure. The highest occupied and lowest unoccupied molecular orbital levels of PAFDQ were −5.37 eV and −3.42 eV, respectively. According to X-ray diffraction measurements, PAFDQ exhibited the formation of an ordered lamellar structure and conventional edge-on π-stacking. The device based on PAFDQ/Y6-BO-4Cl showed the best performance in terms of short circuit current (9.86 mA/cm2), open-circuit voltage (0.76 V), fill factor (44.23%), and power conversion efficiency (3.32%). Moreover, in the PAFDQ/Y6-BO-4Cl-based film, the phase separation of donor-rich and acceptor-rich phases, and the connected dark domains, was observed.

Photovoltaic Characteristics of Hybrid MEH-PPV and TiO2 Nanoparticle Based Organic Solar Cells

2013 ◽  
Vol 667 ◽  
pp. 300-306 ◽  
Author(s):  
Fazlinashatul Suhaidah Zahid ◽  
Puteri Sarah Mohamad Saad ◽  
Mohamed Zahidi Musa ◽  
Mohamad Rusop Mahmood
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Tio2 Nanoparticles ◽  
Conversion Efficiency ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Power Conversion ◽  
Sol Gel ◽  
Short Circuit Current ◽  
Photovoltaic Properties

The photovoltaic properties of organic solar cells based on hybrid poly [2-methoxy-5-(2-ethylhexyloxy-p-phenylenevinylen) (MEH-PPV) and anatase titanium dioxide (TiO2) nanoparticles as a function of TiO2 concentration were investigated. Synthesis of TiO2 nanoparticles was performed by sol-gel immerses heated method and been used as a filler in MEH-PPV polymer matrix. The hybrid MEH-PPV: TiO2 solar cells exhibited increased in light absorption and power conversion efficiency than the pristine organic solar cell. By further optimizing the concentration of TiO2 nanoparticles, the short-circuit current of the hybrid MEH-PPV: TiO2 was reached up to 0.004823 (mA/cm2) and the corresponding power conversion efficiency was 0.000378% was obtained under Air Mass 1.5 illumination which was more than 80% higher compared to the device without TiO2 nanoparticles. This indicates by embedded TiO2 nanoparticles in MEH-PPV matrix encouraging the charge transportation in the active layer of organic solar cells device.

All-polymer solar cells based on a novel narrow-bandgap polymer acceptor with power conversion efficiency over 10%

2019 ◽  
Vol 7 (27) ◽  
pp. 16190-16196 ◽  
Author(s):  
Jingnan Wu ◽  
Yuan Meng ◽  
Xia Guo ◽  
Lei Zhu ◽  
Feng Liu ◽  
...  
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Power Conversion ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Narrow Bandgap ◽  
Polymer Acceptor

A new narrow bandgap polymer acceptor (PN1) based on a fused-ring small molecule acceptor as the core building block was designed and developed. The optimal all-polymer solar cell based on the blend of PM6 and PN1 achieved an outstanding power conversion efficiency of 10.5% with a high open-circuit voltage of 1.0 V, a short circuit current density of 15.2 mA cm−2 and a fill factor of 0.69.

scholarly journals Effect of main and side chain chlorination on the photovoltaic properties of benzodithiophene-alt-benzotriazole polymers

2020 ◽  
Vol 8 (43) ◽  
pp. 15426-15435
Author(s):  
Haijun Bin ◽  
Indunil Angunawela ◽  
Ruijie Ma ◽  
Asritha Nallapaneni ◽  
Chenhui Zhu ◽  
...  
Keyword(s):  
Energy Level ◽  
Charge Transport ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Open Circuit Voltage ◽  
Power Conversion ◽  
Open Circuit ◽  
Side Chain ◽  
Photovoltaic Properties ◽  
Homo Energy Level

Introduction of chlorine in the conjugated side chains significantly improves open-circuit voltage and power conversion efficiency, benefiting from a lower HOMO energy level, well-balanced charge transport and superior nanoscale morphology.

The effect of methyl ammonium chloride doping for perovskite solar cells on structure, crystallization and power conversion efficiency

2020 ◽  
pp. 2150096
Author(s):  
Jing Gao ◽  
Chujian Liao ◽  
Yanqun Guo ◽  
Difan Zhou ◽  
Zhigang Zeng ◽  
...  
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Surface Defects ◽  
Short Circuit ◽  
Power Conversion ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
High Quality ◽  
Perovskite Layer

The perovskite membrane with large particle size, uniform coverage and high quality is the prerequisite for the preparation of efficient and stable perovskite solar cells. Various additives have been used to increase the grain size and improve the film morphology and crystal quality. In this paper, methylammonium chloride (MACl) was proposed to obtain high crystalline quality of [Formula: see text] perovskite absorption layer. The results show that the adding ammonium methyl chloride into the precursor of tricationic perovskite not only passivates surface defects to form high-quality and large-grain perovskite films, but also facilitates the formation of pure [Formula: see text]-phase [Formula: see text]. Meanwhile, the designed perovskite precursor solutions were used to fabricate mesoporous perovskite solar cells (PSCs). Owing to the perovskite layer consisting of optimized MACl doping, the short-circuit current density [Formula: see text] of PSCs reaches 23.81 mA/cm2, which is 2.73 mA/cm2 higher than the primary [Formula: see text] based on PSCs. The obtained power conversion efficiency (PCE) increases from 13.67% to 17.59%.

Effect of Crystallinity on the Performance of P3HT/PC70BM/n-Dodecylthiol Polymer Solar Cells

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Nidal Abu-Zahra ◽  
Mahmoud Algazzar
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Power Conversion ◽  
Crystallization Rate ◽  
Short Circuit Current ◽  
Scanning Calorimetry ◽  
Avrami Model

In this research, n-dodecylthiol was added to P3HT/PC70BM polymer solar cells (PSCs) to improve the crystallinity of P3HT and enhance the phase separation of P3HT/PC70BM. Crystallinity of P3HT:PC70BM doped with 0–5% by volume of n-dodecylthiol was measured using X-ray diffraction (XRD) and differential scanning calorimetry (DSC) techniques. Both methods showed improvement in crystallinity, which resulted in improving the power conversion efficiency (PCE) of polymer solar cells by 33%. In addition, annealing at 150 °C for 30 min showed further improvement in crystallinity with n-dodecylthiol concentration up to 2%. The highest power conversion efficiency of 3.21% was achieved with polymer crystallites size L of 11.2 nm, after annealing at 150 °C for 30 min under a vacuum atmosphere. The smaller crystallite size suggests a shorter path of the charge carriers between P3HT backbones, which could be beneficial to getting a higher short circuit current in the devices made with the additive. Kinetics study of P3HT:PC70BM crystallinity using Avrami model showed a faster crystallization rate (1/t0.5) at higher temperatures.

Novel Linear and Hyperbranched Polythiophene Derivatives Containing Diketopyrrolopyrroles as Linking Groups

2015 ◽  
Vol 1771 ◽  
pp. 213-219
Author(s):  
Sheng-Hsiung Yang ◽  
Chia-Hao Hsieh
Keyword(s):  
Fill Factor ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Power Conversion ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Molecular Weights ◽  
Active Layers ◽  
Film State

ABSTRACTThe goal of this research is to synthesize novel linear and hyperbranched polythiophene derivatives containing diketopyrrolopyrrole (DPP) as linking groups, and to investigate thermal, optical, electrochemical, and photovoltaic properties of those derivatives. Polymers with high regioregularity were synthesized via the Universal Grignard metathesis polymerization. Those linear or hyperbranched polythiophenes containing DPP bridging moieties showed higher molecular weights and better thermal stability compared with normal P3HT. The UV-vis absorption spectra of the DPP-containing polymers are similar to that of P3HT in film state, while they show distinct attenuation in fluorescent emission. Finally, all polymers were blended with PC61BM and used as active layers for fabrication of inverted solar devices. The devices based on those DPP-containing polythiophenes revealed the open-circuit voltage (VOC) of 0.55–0.58 V, the short-circuit current (JSC) of 8.62–16.21 mA/cm2, the fill factor (FF) of 36–41%, and the power conversion efficiency (PCE) of 1.73–3.74%.

Organic Sensitizers Containing Julolidine Moiety for Dye-Sensitized Solar Cells

2008 ◽  
Vol 8 (9) ◽  
pp. 4761-4766 ◽  
Author(s):  
Dong Wook Kim ◽  
Jin Joo Choi ◽  
Man Ku Kang ◽  
Yongku Kang ◽  
Changjin Lee
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Short Circuit ◽  
Power Conversion ◽  
Dye Sensitized Solar Cells ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Sensitized Solar Cells ◽  
Organic Sensitizers

We prepared organic sensitizers (S1 and S2) containing julolidine moiety as a donor, phenyl or phenylene thiophene units as a conjugation bridge, and cyano acetic acid as an acceptor for dye sensitized solar cells. S1 exhibited two absorption maxima at 441 nm (ε = 26 200) and 317 nm (ε = 15 500) due to the π–π* transition of the dye molecule. S2 dyes with an additional thiophene unit showed the absorption maximum extended by 18 nm. DSSCs based on S1 dye achieved 2.66% of power conversion efficiency with 8.3 mA cm−2 of short circuit current, 576 mV of open circuit voltage, and 0.56 of fill factor. DSSCs using S2 dye with a longer conjugation attained only 1.48% of power conversion efficiency. The 0.21 V lower driving force for regeneration of the S2 dye compared to the S1 dye is one of the reasons for low conversion efficiency of the S2 dye.

Sign in / Sign up

Export Citation Format

Share Document