On Experimental Thermal Analysis of BMC Mensolite 3100 Aging

2020 ◽  
Vol 399 ◽  
pp. 129-136
Author(s):  
Pavol Koštial ◽  
Jozef Vlček ◽  
Zora Koštialová Jančíková ◽  
Ivan Ružiak ◽  
Milada Gajtanska ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermal Analysis ◽  
Heat Capacity ◽  
Thermogravimetric Analysis ◽  
Thermal Treatment ◽  
Thermal Capacity ◽  
Irradiation Effect ◽  
Thermally Induced ◽  
Starting Point ◽  
Virgin Sample

The paper is devoted to the study of thermal parameters (specific heat capacity, diffusivity and thermal conductivity) changes after thermally induced aging of BMC Mensolite 3100. Results of several measurements are statistically treated. From obtained results it is visible the greatest correlation in the diffusivity values, i.e. the heat irradiation effect is the smallest on the diffusivity values dispersion, the influence of the heat irradiation on the thermal capacity has approximately the same trend as the thermal conductivity. From the starting point represented by the virgin sample both values decrease and for the sample heated at 300°C it is visible an increase of the above mentioned values under investigation. Results are interpreted by using of the thermogravimetric analysis (TGA). All physical values under this investigation have a dominant decreasing tendency after the thermal treatment described.

scholarly journals Thermal Annealing and Phase Transformation of Serpentine-Like Garnierite

Minerals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 188
Author(s):  
Arun Kumar ◽  
Michele Cassetta ◽  
Marco Giarola ◽  
Marco Zanatta ◽  
Monique Le Guen ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Raman Spectroscopy ◽  
Phase Transformation ◽  
Differential Thermal Analysis ◽  
Thermal Treatment ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Thermally Induced ◽  
X Ray ◽  
Micro Raman Spectroscopy

This study is focused on the vibrational and microstructural aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite were annealed in static air between room temperature and 1000 °C. The kinetic of the transformation was investigated by means of thermogravimetric and differential thermal analysis, and the final product was extensively characterized via micro-Raman spectroscopy and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

Thermal Capacity of Hog-Cooling Pad

2017 ◽  
Vol 33 (6) ◽  
pp. 891-899 ◽  
Author(s):  
Francisco A. Cabezon ◽  
Allan P. Schinckel ◽  
Robert M. Stwalley III
Keyword(s):  
Experimental Investigation ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Response ◽  
Thermal Capacity ◽  
External Heat ◽  
Thermally Induced ◽  
Induced Stress ◽  
Heat Loading ◽  
Convection Cooling

Abstract. Modern hog farrowing operations have reached a state in which the environmental conditions necessary for piglets are vastly different than those required by sows. A hog-cooling pad has been developed by Purdue University researchers to alleviate thermally-induced stress in the sow. Understanding the basic thermal properties of the device is critical to the development of the technology, and this article documents the experimentation performed on the unit to measure some of those characteristics. A preliminary experimental investigation into the thermal response of the device with no external heat loading under a variety of coolant flow and temperatures is presented. The sow-cooling panel reacts as a Newtonian convective device and provides a uniform top surface temperature. The results indicate that device is highly conductive to the top panel and reasonably well insulated from the environment. Keywords: Convection, Cooling, Farrowing, Heat capacity, Swine, Thermal response.

Investigation of Potential Benefits of Using Bricks of High Thermal Capacity and Conductivity in a Rotating Calcining Kiln

2008 ◽  
Author(s):  
Lei Zhao ◽  
Ting Wang
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Capacity ◽  
Potential Energy ◽  
Thermal Energy ◽  
Energy Savings ◽  
Thermal Capacity ◽  
K Value ◽  
Hot Gas ◽  
The Impact

Petroleum coke is processed into calcined coke in a rotary kiln, where the temperature profiles of flue gas and coke bed are highly nonuniform due to different flow and combustion mechanisms. Motivated by saving energy costs, the effect of refractory brick’s thermal properties on potential energy savings is investigated. This study focuses on investigating potential energy savings by replacing inner one third of existing bricks with higher thermal capacity (Cp) and/or higher thermal conductivity (k) bricks. This investigation is motivated by postulating that the bricks with higher thermal capacity can store more thermal energy during the period of contacting with the hot gas and release more heat to the cock bed when the bricks rotate to below and in contact with the coke bed. A rotational, transient marching conduction numerical simulation is conducted using the commercial software FLUENT. The impact of brick heat capacity and thermal conductivity on transporting thermal energy to the coke bed is analyzed. The results show: (a) Increasing the heat capacity of brick layer reduces brick temperature which helps increase the heat transfer between the hot gas and brick, in other words it does help brick store more heat from the hot gas, but, heat transfer between brick and coke is reduced, which is opposite to the original postulation. (b) Higher brick thermal conductivity decreases brick temperature thus increases heat transfer between hot gas and the brick layer. The heat transfer from brick to coke bed is also increased, but not significantly. (c) Usually a brick with a higher Cp value also has a higher k-value. Simulation of a brick layer with both four times higher Cp and k values actually show appreciable heat is transported from the brick to the coke bed for one rotation for both lower and higher Cp and k bricks. The difference is not significant.

scholarly journals On Experimental Thermal Analysis of Solid Materials

2014 ◽  
Vol 14 (6) ◽  
pp. 317-322 ◽  
Author(s):  
Pavel Koštial ◽  
Ivo Špička ◽  
Zora Jančikova ◽  
Jan Valiček ◽  
Marta Harničarova ◽  
...  
Keyword(s):  
Experimental Data ◽  
Thermal Conductivity ◽  
Thermal Analysis ◽  
Heat Capacity ◽  
Cooling Curve ◽  
Solid Materials ◽  
Experimental Conditions ◽  
Capacitance Model ◽  
Special Case

Abstract The paper is devoted to the presentation of a method for measurement of thermal conductivity k, specific heat capacity cp, and thermal diffusivity applying the lumped capacitance model (LCM) as a special case of Newton’s model of cooling. At the specific experimental conditions resulting from the theoretical analysis of the used model, we present a method for experimental determination of all three above mentioned thermal parameters for materials with different thermal transport properties. The input experimental data provide a cooling curve of the tested material. The evaluation of experimental data is realized by software, the fundamental features of which are presented here. The statistical analysis of experimental data was performed.

Investigation of Potential Benefits of Using Bricks of High Thermal Capacity and Conductivity in a Rotating Calcining Kiln

2009 ◽  
Vol 1 (1) ◽  
Author(s):  
Lei Zhao ◽  
Ting Wang
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Capacity ◽  
Potential Energy ◽  
Thermal Energy ◽  
Energy Savings ◽  
Thermal Capacity ◽  
K Value ◽  
Hot Gas ◽  
The Impact

Petroleum coke is processed into calcined coke in a rotary kiln, where the temperature profiles of flue gas and coke bed are highly nonuniform due to different flow and combustion mechanisms. Motivated by saving energy costs, the effect of refractory brick’s thermal properties on potential energy savings is investigated. This study focuses on investigating potential energy savings by replacing inner one-third of existing bricks with higher thermal capacity (Cp) and/or higher thermal-conductivity (k) bricks. This paper investigates the postulation: the bricks with higher thermal capacity could store more thermal energy during the period in contact with the hot gas and would release more heat to the cock bed when the bricks rotate to the position in contact with the coke bed. A rotational transient marching conduction numerical simulation is conducted using the commercial software FLUENT. The impact of brick heat capacity and thermal conductivity on transporting thermal energy to the coke bed is analyzed. The results show the following: (a) Increasing the heat capacity of brick layer reduces brick temperature, which helps increase the heat transfer between the hot gas and brick. In other words, it does help brick to store more heat from the hot gas, but heat transfer between brick and coke is reduced, which is opposite to the original postulation. (b) Higher brick thermal conductivity decreases brick temperature, thus increases heat transfer between hot gas and the brick layer. The heat transfer from brick to coke bed is also increased but not significantly. (c) Since usually a brick with a higher Cp value also has a higher k-value, simulation of a brick layer with both four times higher Cp and k-values actually shows a reduction in the brick temperature, and hence a degradation of the heat transfer between the brick and coke bed. Therefore, replacing the existing brick layer with a high Cp- and/or high k-value brick is not recommended.

scholarly journals Thermal Annealing and Phase Transformation of Serpentine-like Garnierite

2021 ◽  
Author(s):  
Arun Kumar ◽  
Michele Cassetta ◽  
Marco Giarola ◽  
Marco Zanatta ◽  
Monique Le Guen ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Phase Transformation ◽  
Differential Thermal Analysis ◽  
Thermal Treatment ◽  
Thermal Annealing ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Thermally Induced ◽  
X Ray ◽  
Microraman Spectroscopy

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

Development of the room temperature protocol based on room temperature ionic liquids and surfactant ionic liquids for the synthesis of derivatives of 2-amino-thiazoles and thermo-physical analysis of the synthesized derivatives using TGA-DSC.

2020 ◽  
Vol 10 ◽  
Author(s):  
Chandrakant Sarode ◽  
Sachin Yeole ◽  
Ganesh Chaudhari ◽  
Govinda Waghulde ◽  
Gaurav Gupta
Keyword(s):  
Thermal Analysis ◽  
Heat Capacity ◽  
Ionic Liquids ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Room Temperature ◽  
Heat Capacity Data ◽  
General Strategy ◽  
Capacity Data ◽  
Derivatives Of

Aims: To develop an efficient protocol, which involves an elegant exploration of the catalytic potential of both the room temperature and surfactant ionic liquids towards the synthesis of biologically important derivatives of 2-aminothiazole. Objective: Specific heat capacity data as a function of temperature for the synthesized 2- aminothiazole derivatives has been advanced by exploring their thermal profiles. Method: The thermal gravimetry analysis and differential scanning calorimetry techniques are used systematically. Results: The present strategy could prove to be a useful general strategy for researchers working in the field of surfactants and surfactant based ionic liquids towards their exploration in organic synthesis. In addition to that, effect of electronic parameters on the melting temperature of the corresponding 2-aminothiazole has been demonstrated with the help of thermal analysis. Specific heat capacity data as a function of temperature for the synthesized 2-aminothiazole derivatives has also been reported. Conclusion: Melting behavior of the synthesized 2-aminothiazole derivatives is to be described on the basis of electronic effects with the help of thermal analysis. Additionally, the specific heat capacity data can be helpful to the chemists, those are engaged in chemical modelling as well as docking studies. Furthermore, the data also helps to determine valuable thermodynamic parameters such as entropy and enthalpy.

scholarly journals Influence of alkaline modification on selected properties of banana fiber paperbricks

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Abayomi A. Akinwande ◽  
Adeolu A. Adediran ◽  
Oluwatosin A. Balogun ◽  
Oluwaseyi S. Olusoju ◽  
Olanrewaju S. Adesina
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Moisture Absorption ◽  
Water Volume ◽  
Banana Fiber ◽  
Fiber Loading ◽  
Banana Fibers ◽  
Alkaline Modification

AbstractIn a bid to develop paper bricks as alternative masonry units, unmodified banana fibers (UMBF) and alkaline (1 Molar aqueous sodium hydroxide) modified banana fibers (AMBF), fine sand, and ordinary Portland cement were blended with waste paper pulp. The fibers were introduced in varying proportions of 0, 0.5, 1.0 1.5, 2.0, and 2.5 wt% (by weight of the pulp) and curing was done for 28 and 56 days. Properties such as water and moisture absorption, compressive, flexural, and splitting tensile strengths, thermal conductivity, and specific heat capacity were appraised. The outcome of the examinations carried out revealed that water absorption rose with fiber loading while AMBF reinforced samples absorbed lesser water volume than UMBF reinforced samples; a feat occasioned by alkaline treatment of banana fiber. Moisture absorption increased with paper bricks doped with UMBF, while in the case of AMBF-paper bricks, property value was noted to depreciate with increment in AMBF proportion. Fiber loading resulted in improvement of compressive, flexural, and splitting tensile strengths and it was noted that AMBF reinforced samples performed better. The result of the thermal test showed that incorporation of UMBF led to depreciation in thermal conductivity while AMBF infusion in the bricks initiated increment in value. Opposite behaviour was observed for specific heat capacity as UMBF enhanced heat capacity while AMBF led to depreciation. Experimental trend analysis carried out indicates that curing length and alkaline modification of fiber were effective in maximizing the properties of paperbricks for masonry construction.

Sign in / Sign up

Export Citation Format

Share Document