Hierarchical Nanostructured ZnO-CuO Nanocomposite and its Photocatalytic Activity

2015 ◽  
Vol 35 ◽  
pp. 21-26 ◽  
Author(s):  
Susmita Das ◽  
Vimal Chandra Srivastava
Keyword(s):  
Photocatalytic Activity ◽  
Pure Copper ◽  
Ultra Violet ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ultra Violet Radiation ◽  
One Step ◽  
Uv Visible

Metal oxide nanocomposite (ZnO-CuO) was successfully synthesized by one step homogeneous coprecipitation method and further characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron micrograph (SEM), X-ray diffraction analysis (XRD) and UV-visible diffuse reflectance spectra. XRD analysis exhibited presence of pure copper oxide and zinc oxide within the nanocomposite. SEM analysis indicated that the ZnO-CuO nanocomposite was consisted of flower shaped ZnO along with leaf shaped CuO. Photocatalytic activity of nanocomposite was evaluated in terms of degradation of methylene blue (MB) dye solution under ultra-violet radiation. Results showed that the photocatalytic efficiency of ZnO-CuO nanocomposite was higher than its individual pure oxides (ZnO or CuO).

scholarly journals Effect of Re and Tm-site on morphology structure and optical band gap of ReTmO3 (Re: La, Ce, Nd, Gd, Dy, Y and Tm: Fe, Cr) prepared by sol-gel method

2018 ◽  
Vol 64 (4) ◽  
pp. 381
Author(s):  
Muhammad Tufiq Jamil ◽  
Javed Ahmad ◽  
Syed Hamad Bukhari ◽  
Murtaza Saleem
Keyword(s):  
Band Gap ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
X Ray ◽  
Average Grain Size ◽  
Auto Combustion ◽  
Uv Visible

Rare earth nano sized pollycrystalline orthoferrites and orthocromites ReT mO3 (Re = La, Nd, Gd, Dy, Y and T m = Fe, Cr) have been synthesized by sol-gel auto combustion citrate method. The samples have been characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and UV-visible spectroscopy. The samples are single phase as confirmed by XRD analysis and correspond to the orthorhombic crystal symmetry with space group pbnm. Debye Scherer formula and Williamson Hall analysis have been used to calculate the average grain size which is consistent with that of determined from SEM analysis and varied between 25-75 nm. The elemental compositions of all samples have been checked by EDX analysis. Different crystallographic parameters are calculated with strong structural correlation among Re and Tm sites. The optical energy band gap has been calculated by using Tauc relation estimated to be in the range of 1.77 - 1.87 eV and 2.77 - 3.14 eV, for ReFeO3 and ReCrO3, respectively.

Development of Ternary Concrete Utilizing Agricultural Waste Material

2022 ◽  
Author(s):  
Sunita Kumari ◽  
Dhirendra Singhal ◽  
Rinku Walia ◽  
Ajay Rathee
Keyword(s):  
Rice Husk ◽  
Rice Husk Ash ◽  
Agricultural Waste ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Concrete Mix ◽  
Maize Cob

Abstract The present project proposes to utilize rice husk and maize cob husk ash in the cement to mitigate the adverse impact of cement on environment and to enhance the disposal of waste in a sustainable manner. Ternary concrete / MR concrete was prepared by using rise husk and maize cob ash with cement. For the present project, five concrete mixes MR-0 (Control mix), MR-1 (Rice husk ash 10% and MR-2.5%), MR-2 (Rice husk ash 10% and MR-5%), MR-3 (Rice husk ash 10% and MR-2.5%), MR-4 (Rice husk ash 10% and MR-2.5%) were prepared. M35 concrete mix was designed as per IS 10262:2009 for low slump values 0-25mm. The purpose is to find the optimum replacement level of cement in M35 grade ternary concrete for I – Shaped paver blocks.In order to study the effects of these additions, micro-structural and structural properties test of concretes have been conducted. The crystalline properties of control mix and modified concrete are analyzed by Fourier Transform Infrared Spectroscope (FTIR), Scanning Electron Microscopy (SEM), and X-Ray Diffraction (XRD). The results indicated that 10% Rice husk ash and 5% maize cob ash replaced with cement produce a desirable quality of ternary concrete mix having good compressive strength. The results of SEM analysis indicated that the morphology of both concrete were different, showing porous structure at 7 days age and become unsymmetrical with the addition of ashes. After 28 day age, the control mix contained more quantity of ettringite and became denser than ternary concrete. XRD analysis revealed the presence of portlandite in large quantity in controlled mix concrete while MR concrete had the partially hydrated particle of alite.

Synthesis of Nanocomposites of V2OO5©Selenium Nanoparticles and Multiwalled Carbon Nanotubes for Antimicrobial Activity

2021 ◽  
Vol 21 (11) ◽  
pp. 5673-5680
Author(s):  
Muthukrishnan Francklin Philips ◽  
Jothirathinam Thangarathinam ◽  
Jayakumar Princy ◽  
Cyril Arockiaraj Crispin Tina ◽  
Cyril Arockiaraj Crispin Tina ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Antimicrobial Activity ◽  
Multiwalled Carbon Nanotubes ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Multiwalled Carbon ◽  
X Ray ◽  
Functionalized Multiwalled Carbon Nanotubes ◽  
Uv Visible ◽  
Micro Organisms

The authors report the preparation of the nanocomposite comprising of vanadium pentoxide (V2O5) and selenium (Se) nanoparticles and functionalized multiwalled carbon nanotubes (MWCNTs) (V2O5@Se NPs/MWCNTs). Since Se NPs possesses extraordinary physicochemical properties including larger surface area with higher adsorption capacity, V2O5 NPs were adsorbed onto Se NPs surface through physisorption process (designated as V2O5@Se NPs). The nanocomposite synthesized hydrothermally was evaluated for its antimicrobial activity. The morphology and microstructure of the nanocomposite were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis, respectively. Fourier transform infrared spectroscopy (FTIR) and UV-Visible spectroscopy (UV-Vis) were employed to analyze the spectral properties of nanocomposite. The microbicidal efficacy of nanocomposite was tested against Gram-negative (G-)ZGram-positive (G+) bacteria and fungus. This is the first report on the synthesis of V2O5@Se NPs/MWCNTs nanocomposites by chemical method that showed microbicidal effect on micro-organisms. The thiol (-SH) units facilitates the enrichment of V2O5@Se NPs onto MWCNTs surface. Ultimately, it reflects on the significant antimicrobial activity of V2O5@Se NPs/MWCNTs.

Photocatalytic Activity of CuO/ZnO Heterostructure Nanocrystals under UV-Visible Light Irradiation

2014 ◽  
Vol 787 ◽  
pp. 35-40 ◽  
Author(s):  
Xiao Yan Zhou ◽  
Peng Wei Zhou ◽  
Hao Guo ◽  
Bo Yang ◽  
Ru Fei Ren
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Cuo Nanoparticles ◽  
Light Irradiation ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Uv Visible

The p-n junction photocatalysts, p-CuO (at. 0-25%)/n-ZnO nanocomposite were prepared through hydrothermal method without using any organic solvent or surfactant. The as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-Ray spectroscopy, and UV-vis spectroscopy. The results demonstrated that the CuO/ZnO nanocomposite presented a two-dimensional morphology composed of sheet-like ZnO nanostructures adorned with CuO nanoparticles. The photocatalytic activity of CuO/ZnO with different Cu/Zn molar rations and pure ZnO synthesized by the identical synthetic route were evaluated by degrading methylene blue (MB) dye under UV-visible light irradiation. The CuO/ZnO with Cu/Zn molar ratio of 4% exhibits the highest photocatalytic activity compared that of the other photocatalysts under the identical conditions. It is mainly attributed to the increased charge separation rate in the nanocomposite and the extended photo-responding range.

Synthesis, Structural Analysis of Cadmium Sulphide Nanocrystallites

2019 ◽  
Vol 969 ◽  
pp. 169-174
Author(s):  
R. Sivanand ◽  
S. Chellammal ◽  
S. Manivannan
Keyword(s):  
Size Variation ◽  
Cadmium Sulphide ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
Precipitation Method ◽  
Capping Agent ◽  
Energy Dispersive Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

In this paper, the effect of size variation of cadmium sulphide nanocrystallites which have been prepared by precipitation method is analyzed. These prepared samples were studied using X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive analysis of spectroscopy (EDAX) techniques. SEM analysis represents the morphological nature of prepared samples and EDAX indicates the confirmation of elements present in the sample. XRD analysis determines the size of the samples and identifies the structure using miller indices (h k l values) of the nanocrystallies matches with JCPDS. From the XRD analysis, the size variation which depends on dopant, capping agent are discussed and corresponding results are reported in this paper.

scholarly journals Improvement of the Photocatalytic Activity of ZnO/Burkeite Heterostructure Prepared by Combustion Method

Catalysts ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 817 ◽  
Author(s):  
A. Luna-Flores ◽  
M.A. Morales ◽  
R. Agustín-Serrano ◽  
R. Portillo ◽  
J.A. Luna-López ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Combustion Method ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
Solution Combustion Method ◽  
X Ray ◽  
Sem Image ◽  
Particle Aggregates ◽  
One Step ◽  
Ph Dependent

In this work, a novel route is discussed to produce in one step ZnO/Burkeite powders by the modified solution combustion method. The ZnO particles enhance the photocatalytic activity in the degradation of Rhodamine B, in which Burkeite mineral acts as a support due to the pH-dependent morphology of the particle aggregates of the as-synthesized powders. The X-ray diffraction (XRD) characterization shows the presence of a heterostructure: ZnO/Burkeite. The Scanning Electron Microscopy (SEM) image shows a morphological dependence with the pH of the solution used for the synthesis. The results show that the system with the highest degradation (92.4%) corresponds to the case in which ZnO/Burkeite heterostructure was synthesized with a pH 11.

scholarly journals The High Photocatalytic Activity of SnO2Nanoparticles Synthesized by Hydrothermal Method

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Pham Van Viet ◽  
Cao Minh Thi ◽  
Le Van Hieu
Keyword(s):  
Photocatalytic Activity ◽  
Hydrothermal Method ◽  
High Photocatalytic Activity ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Uv Illumination ◽  
Transmission Electron ◽  
Uv Visible ◽  
Tin Oxide Nanoparticles

Tin oxide nanoparticles (SnO2NPs) were prepared at low temperature by hydrothermal method. Synthesized SnO2NPs were confirmedviacharacterization techniques such as UV-visible spectroscopy (UV-vis), X-ray diffraction (XRD), and Transmission Electron Microscope (TEM). The synthesized nanoparticles were in the size of 3 nm and they have high photocatalytic activity. The result showed that SnO2NPs degraded 88.88% MB solution after 30 minutes of UV illumination and reached 90.0% for 120 minutes (2 hours) of UV illumination. Moreover, they degraded 79.26% MB solution after 90 minutes (1.5 hours) under assisted sunlight illumination.

Photoreactive Carbon and Nitrogen-Codoped ZnWO4 Nanoparticles: Synthesis and Reactivity

2012 ◽  
Vol 621 ◽  
pp. 172-177 ◽  
Author(s):  
Su Hua Chen ◽  
Bi Xuan Wang ◽  
Xian Hua Qiu ◽  
Zhen Sheng Xiong
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Visible Region ◽  
Weight Ratio ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Carbon And Nitrogen ◽  
Uv Visible

In order to improve ZnWO4 photocatalytic activity under visible light, the C, N-codoped ZnWO4 nanoparticles have been successfully synthesized by choosing C3N4 generated from tripolycyanamide pyrolysis as the source of Carbon and Nitrogen and the influence of C3N4 concentration on structural, optical and morphological properties of C, N-codoped ZnWO4 using X-ray diffraction (XRD), UV-visible spectroscopy, scanning electron microscopy (SEM) and photocatalytic decoloration of rhodamine B (RhB) aqueous solution under visible light. It was found that the presence of carbon and nitrogen could not improve the crystallization of ZnWO4 species but could enhance their photoabsorption property in the visible region. The results also showed that the photocatalytic activity of the as-prepared ZnWO4 is higher than that of pure ZnWO4 with the optimum effect occurring at RC3N4 = 9 % (the weight ratio of tripolycyanamide to ZnWO4)

The Effect of CaCO3 Addition on Physical Properties of ZnO-Based Crystal Glaze

2012 ◽  
Vol 620 ◽  
pp. 12-16 ◽  
Author(s):  
Abdul Rashid Jamaludin ◽  
Shah Rizal Kasim ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Calcium Carbonate ◽  
Scanning Electron Microscope ◽  
Physical Properties ◽  
Crystallization Temperature ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

The effects of calcium carbonate (CaCO3) addition on the physical properties of ZnO-based crystal glaze batches were investigated. Samples were fired at different gloss firing temperatures ranging from 1180-1220°C with 3 hours soaking at 1060°C crystallization temperature. X-ray diffraction (XRD) analysis identifiedthe crystal phase occurred as willemite (Zn2SiO4) and the scanning electron microscope (SEM) analysis indicated that willemite crystals are in the acicular needle like shape that formed spherulite. The intensities of willemite peaks decreased with CaCO3 addition and completely vanished at 5.0 wt% CaCO3. Varied formation of spherulites developed of the surface of crystal glaze as the flows of the glaze stretched further as the amount of CaCO3 increased.

scholarly journals Synthesis of copper oxide nano-rice structures for enhancement of photocatalytic activity under natural sunlight

2019 ◽  
Vol 20 (5) ◽  
pp. 253-262
Author(s):  
Roonak Abdul Salam A.Alkareem
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Electron Microscope ◽  
Copper Oxide ◽  
High Photocatalytic Activity ◽  
X Ray Diffraction ◽  
Methylene Blue Degradation ◽  
X Ray ◽  
Uv Visible ◽  
Scanning Electron

In this work, copper oxide (CuO) nano-rice structure was prepared by hydrothermal method. The prepared samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), and UV-visible spectrophotometer. CuO nano-rice structure showed high photocatalytic activity towards degradation of methylene blue (MB). Hydrothermally growth of CuO provided uniformly distributed nano-rice structures with high degradation efficiency (90.41%) and rate constant (kt) 16.6 × 10-2 min-1 for methylene blue degradation.

Sign in / Sign up

Export Citation Format

Share Document