Fatigue Properties of Austenitic Stainless Steels with Different Nitrogen

2004 ◽  
Vol 261-263 ◽  
pp. 1215-1220 ◽  
Author(s):  
Nobusuke Hattori ◽  
S. Nishida
Keyword(s):  
Fatigue Strength ◽  
Stainless Steels ◽  
Stress Amplitude ◽  
Austenitic Stainless Steels ◽  
Fatigue Tests ◽  
The Other ◽  
Fatigue Properties ◽  
Transformation Ratio ◽  
Other Hand ◽  
Knee Point

The fatigue properties of austenitic stainless steels become inevitably important when using in structural materials. The authors have performed fatigue tests to investigate the effect of nitrogen content on fatigue properties of typical austenitic stainless steels (SUS304) and two kinds of nitrogen-contained SUS304 (SUS304N and YUS170). The main results obtained in this study are as follows; (1) The knee point in S-N curves exists for SUS304 and SUS304N, but does not exist for YUS170. (2) The fatigue limit of SUS304N is higher than that of SUS304. On the other hand, the fatigue strength by 107 cycles of YUS170 is lower than those of SUS304 and SUS304N. (3) For SUS304, the transformation ratio increases with increase in stress amplitude. On the other hand, the transformation ratio of SUS304N is very small and that of YUS170 remains essentially zero.

Effect of Strain-Induced Martensitic Transformation on Coaxing Effect of Austenitic Stainless Steels

2008 ◽  
Vol 385-387 ◽  
pp. 505-508
Author(s):  
Jae Woong Jung ◽  
Masaki Nakajima ◽  
Yoshihiko Uematsu ◽  
Keiro Tokaji ◽  
Masayuki Akita
Keyword(s):  
Martensitic Transformation ◽  
Stainless Steels ◽  
Work Hardening ◽  
Strain Aging ◽  
Austenitic Stainless Steels ◽  
Fatigue Tests ◽  
The Other ◽  
Conventional Tests ◽  
Materials Used ◽  
Type 304

The effects of martensitic transformation on the coaxing behavior were studied in austenitic stainless steels. The materials used were austenitic stainless steels, type 304 and 316. Conventional fatigue tests and stress-incremental fatigue tests were performed using specimens subjected to several tensile prestrains from 5% to 60%. Under conventional tests, the fatigue strengths of both steels increased with increasing prestrain. Under stress-incremental tests, 304 steel showed a marked coaxing effect, where the failure stress significantly increased irrespective of prestrain level. On the other hand, the coaxing effect in 316 steel decreased with increasing prestrain up to 15%, where the failure stresses were nearly the same. Above this prestrain level, the coaxing effect increased with increasing prestrain. In 304 steel, the coaxing effect is primarily dominated by work hardening at low prestrains, while the effect of strain-induced martensitic transformation increases with increasing prestrain. The coaxing effect in 316 steel is dominated by both work hardening and strain aging at low prestrains, but strain-induced martensitic transformation could play a significant role at high prestrains.

scholarly journals Controlling Angular Distortion in Manual Metal Arc Welding of Austenitic Stainless Steels Using Back-step Technique

2018 ◽  
Vol 26 (2) ◽  
pp. 311-319
Author(s):  
Abdul Sameea Jasim Abdul Zehra Jilabi
Keyword(s):  
Stainless Steels ◽  
Nuclear Power ◽  
Elevated Temperatures ◽  
Austenitic Stainless Steels ◽  
Industrial Applications ◽  
The Other ◽  
Angular Distortion ◽  
Mma Welding ◽  
Other Hand ◽  
Wide Range

Nowadays, austenitic stainless steels (A.S.S.) have many industrial applications in the fields of chemical and petrochemical processing, marine, medicine, water treatment, petroleum refining, food and drinks processing, nuclear power generation etc. The secret behind this wide range of applications is the fact that A.S.S. have great corrosion resistance, high strength and scale resistance at elevated temperatures, good ductility at low temperatures approached to absolute zero in addition to notable weldability. On the other hand, manual metal arc (MMA) is probably the most common process used for the welding of A.S.S. Unfortunately, MMA welding of A.S.S. could be associated with considerable distortion. Uncontrolled or excessive distortion usually increases the cost of the production process due to the high expense of rectification or replacing the weldment by a non-distorted one. MMA welding of A.S.S. was carried out using the back-step technique with various bead lengths, and without using this technique for comparison. Results have showed that the angular distortion was a function of the bead length in the back-step welding of A.S.S. The angular distortion decreased by (14.32%) when the back-step technique was used with a (60 mm) length for each bead, and by (41.08%) when the bead length was (40 mm). On the other hand, it increased by (25%) when the back-step technique was done with a (30 mm) length for each bead.

Effect of Pre-Strain and Roller Working on Torsional Fatigue Properties of a Structural Steel

2011 ◽  
Vol 295-297 ◽  
pp. 2227-2230
Author(s):  
Cong Ling Zhou
Keyword(s):  
Residual Stress ◽  
Fatigue Limit ◽  
Work Hardening ◽  
Compressive Residual Stress ◽  
Strain Ratio ◽  
Fatigue Tests ◽  
The Other ◽  
Fatigue Properties ◽  
Torsional Fatigue ◽  
Stress Work

In this study, fatigue tests have been performed using two kinds of specimens made of 25 steel. One is pre-strained specimen with pre-strain ratio changing from 2% to 8% by tension, the other is roller worked with deformation of 0.5 mm and 1.0 mm in diameter direction. In the case of pre-strained specimen, the fatigue limit increases according to increase of tensile pre-strain, the fatigue limit of 8% pre-strained specimen is 25% higher than that of non-pre-strained one; in the case of roller worked specimen, the fatigue limit of R05 and R10 is 126% and 143% to that of non-roller worked specimen, respectively. These remarkable improvements of fatigue limit would be caused by the existence of compressive residual stress, work-hardening and the elongated microscopic structures.

Characterization of nanocrystalline surface layer induced by shot peening and effect on their fatigue strength.

2004 ◽  
Vol 843 ◽  
Author(s):  
Hideo Mano ◽  
Kondo Satoru ◽  
Akihito Matsumuro ◽  
Toru Imura
Keyword(s):  
Residual Stress ◽  
Surface Layer ◽  
Fatigue Strength ◽  
Vickers Hardness ◽  
Shot Peening ◽  
White Layer ◽  
The Other ◽  
Fatigue Properties ◽  
Nanocrystalline Layer

ABSTRACTThe shot peening process is known to produce a hard layer, known as the white layer” on the surface of coil springs. However, little is known about the fatigue properties of this white-layer.In this study, coil springs with a white-layer were manufactured. The surface of these springs was then examined using micro Vickers hardness, FE-SEM etc. to test fatigue strength of the springs.From the results obtained, a microstructure of the white-layer with grain size of 50–100 nm was observed, with a Vickers hardness rating of 8–10 GPa.Tow category springs were manufactured utilizing a double-peening process. These springs had the same residual stress destruction and surface roughness. Only one difference was observed: one spring had a nanocrystalline layer on the surface, while the other did not. The results of the fatigue test realized an increase in the fatigue life of the nanocrystalline surface layer by 9%.

Thermal Fatigue Characteristics of Heat-Resisting Stainless Steel for Automotive Exhaust

2007 ◽  
Vol 539-543 ◽  
pp. 4944-4949 ◽  
Author(s):  
Tae Kwon Ha ◽  
Hwan Jin Sung
Keyword(s):  
Thermal Fatigue ◽  
Stainless Steels ◽  
Fatigue Property ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Automotive Exhaust ◽  
Load Relaxation ◽  
Temperature Ranges ◽  
Fatigue Characteristics ◽  
Efficiency And Reliability

Thermal fatigue is a complex phenomenon encountered in materials exposed to cyclically varying temperatures in the presence or absence of external load. Continually increasing working temperature and growing need for greater efficiency and reliability of automotive exhaust require immediate investigation into the thermal fatigue properties especially of high temperature stainless steels. In this study, thermal fatigue properties of 304 and 429EM stainless steels have been evaluated in the temperature ranges of 200-800oC and 200-900oC. Systematic methods for control of temperatures within the predetermined range and measurement of load applied to specimens as a function of temperature during thermal cycles have been established. Thermal fatigue tests were conducted under fully constrained condition, where both ends of specimens were completely fixed. Thermal fatigue property of STS 304 was superior to that of STS 429EM. Load relaxation behavior at the temperatures of thermal cycle was closely related with the thermal fatigue property.

scholarly journals Effects of thermomechanical history and environment on the fatigue behavior of (β)-Ti-Nb implant alloys

2018 ◽  
Vol 165 ◽  
pp. 06001 ◽  
Author(s):  
André Reck ◽  
Stefan Pilz ◽  
Ulrich Thormann ◽  
Volker Alt ◽  
Annett Gebert ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Cyclic Loading ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Grain Structure ◽  
Fatigue Properties ◽  
Β Phase ◽  
Α Phase ◽  
Nb Content ◽  
Implant Alloys

This study examined the fatigue properties of a newly developed cast and thermomechanical processed (β)-Ti-40Nb alloy for a possible application as biomedical alloy due to exceptional low Young’s modulus (64-73 GPa), high corrosion resistance and ductility (20-26%). Focusing on the influence of two microstructural states with fully recrystallized β-grain structure as well as an aged condition with nanometer-sized ω-precipitates, tension-compression fatigue tests (R=-1) were carried out under lab-air and showed significant differences depending on the β-phase stability under cyclic loading. Present ω- precipitates stabilized the β-phase against martensitic α’’ phase transformations leading to an increased fatigue limit of 288 MPa compared to the recrystallized state (225 MPa), where mechanical polishing and subsequent cyclic loading led to formation of α’’-phase due to the metastability of the β-phase. Additional studied commercially available (β)-Ti-45Nb alloy revealed slightly higher fatigue strength (300 MPa) and suggest a change in the dominating cyclic deformation mechanisms according to the sensitive dependence on the Nb-content. Further tests in simulated body fluid (SBF) at 37°C showed no decrease in fatigue strength due to the effect of corrosion and prove the excellent corrosion fatigue resistance of this alloy type under given test conditions.

Fatigue Behavior of Age-Hardening Cu-6Ni-1.5Si Alloys with Different Grain Sizes

2021 ◽  
Vol 1016 ◽  
pp. 125-131
Author(s):  
Masahiro Goto ◽  
T. Yamamoto ◽  
S.Z. Han ◽  
J. Kitamura ◽  
J.H. Ahn ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Fatigue Strength ◽  
Solution Heat Treatment ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
The Other ◽  
Age Hardening ◽  
Grain Sizes ◽  
Thermomechanical Processes

On the thermomechanical treatments of Cu-Ni-Si alloy, cold-rolling (CR) before solution heat treatment (SHT) is commonly conducted to eliminate defects in a casting slab. In addition, a rolling is applied to reduce/adjust the thickness of casting slab before SHT. In a heavily deformed microstructure by CR, on the other hand, grain growth during a heating in SHT is likely to occur as the result of recrystallization. In general, tensile strength and fatigue strength tend to decrease with an increase in the grain size. However, the effect of difference in grain sizes produced by with and without CR before SHT on the fatigue strength is unclear. In the present study, fatigue tests of Cu-6Ni-Si alloy smooth specimens with a grain fabricated through different thermomechanical processes were conducted. The fatigue behavior of Cu-Ni-Si alloy was discussed.

Development of New Design Fatigue Curves in Japan: Proposal of a New Fatigue Evaluation Method

2018 ◽  
Author(s):  
Seiji Asada ◽  
Akihiko Hirano ◽  
Toshiyuki Saito ◽  
Yasukazu Takada ◽  
Hideo Kobayashi
Keyword(s):  
Stainless Steels ◽  
Evaluation Method ◽  
Austenitic Stainless Steels ◽  
Fatigue Tests ◽  
Carbon Steels ◽  
Low Alloy Steels ◽  
Stress Effect ◽  
Fatigue Data ◽  
Alloy Steels ◽  
Fatigue Evaluation

In order to develop new design fatigue curves for carbon steels & low-alloy steels and austenitic stainless steels and a new design fatigue evaluation method that are rational and have clear design basis, Design Fatigue Curve (DFC) Phase 1 subcommittee and Phase 2 subcommittee were established in the Atomic Energy Research Committee in the Japan Welding Engineering Society (JWES). The study on design fatigue curves was actively performed in the subcommittees. In the subcommittees, domestic and foreign fatigue data of small test specimens in air were collected and a comprehensive fatigue database (≈6000 data) was constructed and the accurate best-fit curves of carbon steels & low-alloy steels and austenitic stainless steels were developed. Design factors were investigated. Also, a Japanese utility collaborative project performed large scale fatigue tests using austenitic stainless steel piping and low-alloy steel flat plates as well as fatigue tests using small specimens to obtain not only basic data but also fatigue data of mean stress effect, surface finish effect and size effect. Those test results were provided to the subcommittee and utilized the above studies. Based on the above studies, a new fatigue evaluation method has been developed.

scholarly journals Effect of Microstructure on Creep Fatigue Properties for Type 316 Austenitic Stainless Steels

1996 ◽  
Vol 82 (6) ◽  
pp. 538-543 ◽  
Author(s):  
Nobuhiro FUJITA ◽  
Takanori NAKAZAWA ◽  
Hazime KOMATSU ◽  
Hitoshi KAGUCHI ◽  
Hideaki KANEKO ◽  
...  
Keyword(s):  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
Fatigue Properties ◽  
Creep Fatigue ◽  
Effect Of Microstructure

scholarly journals The Effects of Notches on the Fatigue Strength of Steel Structures

2019 ◽  
Vol 279 ◽  
pp. 02001
Author(s):  
Pavol Juhas
Keyword(s):  
Fatigue Strength ◽  
Steel Structures ◽  
Life Time ◽  
Fatigue Tests ◽  
Constructional Steel ◽  
Fatigue Properties ◽  
Stress Range ◽  
Time Data ◽  
Butt Weld ◽  
Applied Loading

The paper informs about the research devoted to load–carrying capacity, fatigue strength and life–time of welded steel structures. The experimental programme comprises fatigue tests of constructional steel S380 (QStE 380 TM). In the first stage 35 specimens were tested: 9 without any weld connection, 14 with transverse milled butt weld and 12 with transverse rough butt weld. The applied loading in this stage was harmonic with constant stress range. All tests ended by fatigue failure. The second part of the research comprised the tests with block simulated loading with variable stress range. The third part applied continuous recording of stresses and strains in critical sections, that gave information about the local failure development in time. Data sets have allowed to define fatigue properties of investigated steel and degradation effects of used welds including the initiation time of remarkable changes in stress-strain stage expressed through the total kinetic energy. The degradation effects of welds on fatigue strength of structural steels were confirmed, especially it was the case of rough welds - without additional milling. Additionally, the differences in the fatigue curves inclinations were indicated that can depend on the level of fatigue strength. The applied approach gives an opportunity to analyse the effects of actual loading process and improve the methodology of judgement of fatigue strength and life-time of steel elements. Reasonable fatigue properties of this steel suggest it for using also in severe technology structures.

Sign in / Sign up

Export Citation Format

Share Document