An Elastoplastic Model for Granular Materials Exhibiting Particle Crushing

2007 ◽  
Vol 340-341 ◽  
pp. 1273-1278 ◽  
Author(s):  
De An Sun ◽  
Wen Xiong Huang ◽  
Dai Chao Sheng ◽  
Haruyuki Yamamoto
Keyword(s):  
Shear Strength ◽  
Granular Materials ◽  
Triaxial Compression ◽  
Model Performance ◽  
Confining Pressure ◽  
Model Parameters ◽  
Compression Tests ◽  
Particle Crushing ◽  
Wide Range ◽  
Triaxial Compression Tests

A practical elastoplastic constitutive model for granular materials is presented. And the model is suitable for description of the material behaviour for a wide range of stresses, including those sufficient to cause particle crushing. With a limited number of model parameters, the model can predict the confining-pressure dependent stress-strain relation and shear strength of granular materials in three-dimensional stresses, especially of variation of shear strength and dilatancy characteristics due to particle crushing under high confining pressure. The model parameters, which have clear physical meanings, can be determined from the results of isotropic compression test and conventional triaxial compression tests. The model performance is demonstrated for triaxial compression tests of a sand for a wide range of the confining-pressure from 0.2MPa to 8.0MPa.

Mechanical Properties of Bentonite-Sand Mixtures Under Triaxial Stress Condition

1994 ◽  
Vol 353 ◽  
Author(s):  
M. Umedera ◽  
A. Fujiwara ◽  
N. Yasufuku ◽  
M. Hyodo ◽  
H. Murata
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strength Properties ◽  
Compression Tests ◽  
Optimum Water Content ◽  
Triaxial Compression Tests ◽  
Optimum Water

AbstractA series of triaxial compression tests is being conducted under the drained condition on bentonite and sand mixtures, known as buffer, in saturated and optimum water content states to clarify the mechanical properties of the buffer.It was found that the mechanical properties of bentonite and sand mixtures are strongly influenced by water and bentonite contents: shear strength in a saturated state is less than that in an optimum water content state; shear strength decreases rapidly with increasing bentonite content. Strength properties are much dependent on confining pressure.

Experimental study of a naturally weathered stiff clay

2016 ◽  
Vol 53 (12) ◽  
pp. 2047-2057 ◽  
Author(s):  
Maria Clorinda Mandaglio ◽  
Nicola Moraci ◽  
Marco Rosone ◽  
Camillo Airò Farulla
Keyword(s):  
Shear Strength ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Experimental Studies ◽  
Water Retention Curve ◽  
Compression Tests ◽  
Weathered Soils ◽  
Wide Range ◽  
Stiff Clay ◽  
Triaxial Compression Tests

Studying the shear strength of a naturally weathered clay is important to understand rain-induced slope failures in weathered soils. However, experimental studies on naturally weathered soils are limited. The paper focuses on the laboratory experimental investigation carried out to analyse the shear strength of a naturally weathered stiff clay that can be found in unsaturated conditions in situ. This has an important practical relevance in the evaluation of the stability conditions of natural slopes at clay outcrops. Different experimental techniques of suction measurement were used to obtain the soil-water retention curve of the clay over a wide range of suctions. Scanning electronic microscope (SEM) observations and results of mercury intrusion porosimetry (MIP) tests are also presented to highlight the considerable fabric arrangement modifications at the microstructural level induced by wetting–drying processes. Moreover, isotropic consolidated drained triaxial compression tests on undisturbed and reconstituted saturated specimens and controlled-suction triaxial compression tests on unsaturated undisturbed specimens were carried out. The test results allowed examination of the saturated mechanical behaviour of clay and comparison of the mechanical behaviour of the saturated material with that in an unsaturated condition.

scholarly journals Triaxial Testing of Geosynthetics Reinforced Tailings with Different Reinforced Layers

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Fu Yi ◽  
Changbo Du
Keyword(s):  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Test Results ◽  
Compression Tests ◽  
Strength Index ◽  
Stress Strain ◽  
High Confining Pressure ◽  
Zhang Model ◽  
Triaxial Compression Tests

To evaluate the shear properties of geotextile-reinforced tailings, triaxial compression tests were performed on geogrids and geotextiles with zero, one, two, and four reinforced layers. The stress–strain characteristics and reinforcement effects of the reinforced tailings with different layers were analyzed. According to the test results, the geogrid stress–strain curves show hardening characteristics, whereas the geotextile stress–strain curves have strain-softening properties. With more reinforced layers, the hardening or softening characteristics become more prominent. We demonstrate that the stress–strain curves of geogrids and geotextile reinforced tailings under different reinforced layers can be fitted by the Duncan–Zhang model, which indicates that the pseudo-cohesion of shear strength index increases linearly whereas the friction angle remains primarily unchanged with the increase in reinforced layers. In addition, we observed that, although the strength of the reinforced tailings increases substantially, the reinforcement effect is more significant at a low confining pressure than at a high confining pressure. On the contrary, the triaxial specimen strength decreases with the increase in the number of reinforced layers. Our findings can provide valuable input toward the design and application of reinforced engineering.

Experimental Study on Shear Strength Considering Initial Void Ratio and Plasticity Index

2013 ◽  
Vol 405-408 ◽  
pp. 63-67
Author(s):  
Xing Chen Wang ◽  
Ri Qing Xu ◽  
Jian Feng Zhu
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Deviatoric Stress ◽  
Plasticity Index ◽  
Test Results ◽  
Compression Tests ◽  
Functional Relationships ◽  
Initial Void Ratio

A series of drained triaxial compression tests under different conditions were performed to quantitatively study the influence of the initial void ratio and plasticity index on the shear strength of remolded saturated clays. The test results show that both the peak stress friction angle and peak deviatoric stress decrease with increasing initial void ratio and plasticity index of the soil under the same confining pressure; whereas, they increase with increasing confining pressure of the soil under the same initial void ratio and plasticity index. A new synthesized physical parameter λ, which simultaneously represent both the type and the condition of remolded saturated clays, is defined based on the test results in this work. The functional relationships among the parameters φd and peak deviatoric stress in Mohr-Coulomb equation and the parameter λ are established to develop a modified Mohr-Coulomb equation by considering physical properties of soil. In this equation, only two input parameters, i.e., λ and the confine pressure, are needed to predict the shear strength of the soil. In order to check the accuracy of the proposed equation, laboratory tests were conducted to evaluate against the predicted results. The results show that the peak shear strength of remolded saturated clays can be well described by the proposed equation. Key words: shear strength; Mohr-Coulomb equation; remolded saturated clays; initial void ratio; plasticity index.

scholarly journals Triaxial Testing on Geogrid-reinforced Granular Soils

2021 ◽  
Vol 1200 (1) ◽  
pp. 012030
Author(s):  
Tigo Mindiastiwi ◽  
Po-Kai Wu ◽  
Agus Bambang Siswanto ◽  
Mukhamad Afif Salim
Keyword(s):  
Shear Strength ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Reinforced Soil ◽  
Deviatoric Stress ◽  
Granular Soils ◽  
Peak Shear Strength ◽  
Compression Tests ◽  
Soil C ◽  
Dense Sand

Abstract Laboratory triaxial compression tests were carried out to investigate the mechanical behavior of dense sand and geogrid-reinforced granular soils. The tested sand having its mean particle size (D50) equal to 0.6 mm was adopted. Three geogrids with different longitudinal and transverse nominal strengths were used. The dimensions of the cylindrical soil specimen were 70 mm (diameter) × 160 mm (height). The relative density was equal to 70% for all tests. The reinforced sand specimens with one or two geogrid layers were sheared under effective confining pressures (σ′3) equal to 50 kPa. The test results of unreinforced sand indicate the general stress-strain behavior of dense sand when sheared, whereas the deviatoric stress reaches its peak value, after which it gradually decreases to ultimate value (σ1 - σ3)ult. The difference of effective confining pressure indicates that the peak of deviatoric stress Δσd = (σ1 - σ3) increases with the increase in effective confining pressure (σ′3), while the peak principal stress ratio (σ′1/σ′3) decreases with the increase (σ′3). The friction angle (ϕ′)and cohesion (c′), defined by analytical and graphical methods for unreinforced sand. Geogrid as reinforcement increasing peak shear strength. The increasing peak shear strength is more pronounced with a higher number of geogrid and the geogrid with higher stiffness. Increased in confining stress inside reinforced soil mass (Δσ3R) can be interpreted by cohesive reinforced soil (CR).

scholarly journals Interpretation of undrained shear strength observed in confined triaxial compression tests on compacted clay

2021 ◽  
Author(s):  
Chee K. Wong ◽  
Martin Lun ◽  
Ron C.K. Wong
Keyword(s):  
Shear Strength ◽  
Unsaturated Soil ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Undrained Shear Strength ◽  
Compacted Clay ◽  
Compression Tests ◽  
Basic Model ◽  
Triaxial Compression Tests ◽  
Undrained Shear

This paper presents an interpretation technique to quantify the effects of compaction state and matric suction on the undrained shear strength of compacted clay under confined undrained triaxial compression. This novel technique is based on the mathematical frameworks of SHANSEP (Stress History and Normalized Soil Engineering Property) method for saturated soil and BBM (Barcelona Basic model) for unsaturated soil. Test data of compacted Calgary till were analyzed and interpreted using the proposed technique. The interpretation technique is very useful in delineating the relative impacts of the factors on the behavioral trends in measured undrained shear strength. It was found that in addition to the initial compacted void ratio and suction, soil structure and failure mode exert significant influence on the undrained shear strength of compacted clay. This technique is attractive to engineering practitioners because the confined undrained compression tests (with no pore air and water pressure measurement) are much simpler and less time consuming compared to rigorous laboratory tests on unsaturated soil.

Bionic Jump Mechanism Analysis Based on Locust Hind

2013 ◽  
Vol 461 ◽  
pp. 184-190
Author(s):  
Dong Hui Chen ◽  
Heng Xie ◽  
Shao Bo Ye ◽  
Ting Wu ◽  
Xin Lu ◽  
...  
Keyword(s):  
Shear Strength ◽  
Triaxial Compression ◽  
Mechanism Analysis ◽  
Compression Tests ◽  
Fibrous Root ◽  
Factors Affecting ◽  
Complex Shear ◽  
Different Types ◽  
Soil Complex ◽  
Triaxial Compression Tests

The structure of corn stubble was complex and closely combined with the soil, so dig location and root-soil separation are the urgent problem of the manufacturing of corn stubble harvesting machinery. This paper mainly focuses on investigating the interaction principles of corn stubble and soil which by the UU triaxial compression tests. Compared the shear strength of three different types of corn root-soil complexes (vertical root, horizontal root, complex root) and pure soil, and analyzed three important factors affecting the root-soil complex shear strength, it was shown that the presence of corn fibrous root can enhance the soil shear strength and different with their layout types. It will provide a theoretical basis for the design of bionic agricultural tillage components for root- soil separation.

Experimental Study of Stress-Strain Characteristics of the Fly Ash Blended with Curing Agent

2010 ◽  
Vol 168-170 ◽  
pp. 1934-1942
Author(s):  
Zheng Shen ◽  
Lan Zong ◽  
Xiang Dong
Keyword(s):  
Fly Ash ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Uniaxial Stress ◽  
Curing Agent ◽  
Compression Tests ◽  
Growth Trend ◽  
Stress Strain ◽  
Confining Pressures ◽  
Triaxial Compression Tests

The stress-strain characteristics of the fly ash blended with curing agent was studied using uniaxial and triaxial compression tests. Curing agent JNS-2 was used as the stabilizing agents in sample preparation. Four curing agent JNS-2 contents of 3%, 6%, 9% and 12% were selected for sample preparation. UU triaxial compression tests were conducted in a range of confining pressures from 100 kPa to 300 kPa. The experimental results obtained from the laboratory tests showed that curing age, mixture ratio, compaction degree and confining pressures had significant influence on the shape of curves. Uniaxial stress-strain test results demonstrated that the latter strength and deformation characteristics of the fly ash blended with curing agent grew little and with the increase of curing agent amount and compaction factor, the curve of uniaxial stress-strain changed significantly. On the other hand, triaxial stress-strain test results indicted that the failure strain showed a partial negative growth trend with the increase of curing agent amount, and the failure stress showed a partial positive growth trend with the increase of curing agent amount. When the curve was at high confining pressure, it showed hardening type, when at low confining pressure it showed softening type.

Isothermal modeling of sand–bentonite mixtures at elevated temperatures

1995 ◽  
Vol 32 (1) ◽  
pp. 78-88 ◽  
Author(s):  
B.E. Lingnau ◽  
J. Graham ◽  
N. Tanaka
Keyword(s):  
Shear Strength ◽  
Elevated Temperatures ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Compression Tests ◽  
Strain Behavior ◽  
Bentonite Buffer ◽  
State Boundary ◽  
Increasing Temperature ◽  
Triaxial Compression Tests

Two models are proposed for describing the stress–strain behavior of sand–bentonite (buffer) mixtures at elevated temperatures: (1) isothermal pseudoelasticity and (2) isothermal elastic-plasticity. Data to support the models come from consolidated undrained triaxial compression tests performed on dense saturated buffer specimens at effective confining stresses up to 9.0 MPa and temperatures of 26°, 65°, and 100 °C. Measurements indicate that volumes decrease with increasing temperature if the tests are carried out under drained conditions. These trends can be modelled by a family of hardening lines in semilog compression space. Power law relationships are presented for undrained shear-strength envelopes that increase in size with an increase in temperature. The slopes of unload-reload lines, κ, in semilog compression space vary with temperature and can be related to systematic variation in the friction angle [Formula: see text]. The shear modulus G50 at 50% peak strength also depends on temperature. Several plotting techniques are used to show the existence of different state boundary surfaces for each test temperature. Key words : sand–bentonite, buffer, compression, shear strength, temperature, modelling.

Mechanism of High-velocity Projectile Penetration into Concrete

2012 ◽  
Vol 13 (2) ◽  
pp. 137-143
Author(s):  
Hai-Jun Wu
Keyword(s):  
Yield Criterion ◽  
Triaxial Compression ◽  
Target Material ◽  
Cavity Expansion ◽  
Model Parameters ◽  
Compression Tests ◽  
Expansion Theory ◽  
Cavity Expansion Theory ◽  
Triaxial Compression Tests ◽  
Spherical Cavity Expansion

Abstract The penetration depth of rigid projectiles is investigated using the modified spherical cavity expansion theory and the Holmquist–Johnson–Cook (HJC) model for the concrete targets, in which the model parameters used in the Mohr–Coulomb Tresca-limit yield criterion are obtained by the triaxial compression tests. By comparing the cavity expansion pressures of the concrete samples with two different types of aggregate, the influence of the aggregate hardness on the penetration processes is discussed. With the analysis of the tractions acted on the projectile nose, the influences of the projectile and target material properties as well as the projectile structure on the transition impact velocity are also discussed. By comparing the theoretical results with the experimental data, two penetration mechanisms are demonstrated for the ogive-nose projectile penetration into concrete with the striking velocities up to 2.0 km/s.

Sign in / Sign up

Export Citation Format

Share Document