Experimental Investigation on Residual Stress of Model S1100 of Crankshaft Chamfer Based on XRD

2007 ◽  
Vol 353-358 ◽  
pp. 2301-2304
Author(s):  
Yong Kang Zhang ◽  
De Jun Kong ◽  
Jin Zhon Lu ◽  
Ai Xin Feng ◽  
Xu Dong Ren ◽  
...  
Keyword(s):  
Residual Stress ◽  
Experimental Investigation ◽  
Fatigue Life ◽  
Stress Distribution ◽  
Service Life ◽  
Residual Stresses ◽  
Fatigue Testing ◽  
Residual Stress Distribution ◽  
Isothermal Quenching ◽  
Main Factors

Residual stresses of model S1100 of crankshaft chamfer were measured by the technology of XRD. The distributions of residual stresses under mechanical peening, mechanical rolling and isothermal quenching are measured, and the tests of fatigue life were conducted. The results showed that the distribution of residual stress by machining in the crankshaft chamfer is complicated, which is at the tensile-compressive status, and it is one of the main factors to affect fatigue life of the crankshaft; isothermal quenching improves the distribution of residual stress, and tensile stress of the crankshaft chamfer is changed into the compressive stress, which may satisfy the requests of fatigue testing for 5 × 106 cycles. Although the mechanical rolling improved the residual stress distribution in the chamfer linked with the crank, tensile stresses in the chamfer connected with the linkage also increase, which influences the service life of the crankshaft.

Prediction of Residual Stresses in Mooring Chains and its Impact on Fatigue Life

2017 ◽  
Author(s):  
Imanol Martinez Perez ◽  
Philippe Bastid ◽  
Vengatesan Venugopal
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Fatigue Life ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Sensitivity Study ◽  
Residual Stress Distribution ◽  
Residual Stress Field ◽  
Loading Mode ◽  
A Chain

This paper reports the results of a study conducted to investigate how residual stresses generated during the manufacturing process and subsequent proof loading may affect the fatigue life of mooring chains. The present paper shows the quantitative predictions of residual stress field obtained from finite element models of the fabrication process, and discusses their effect on the fatigue life of chain links depending on the loading mode. The models combine heat transfer analyses for the prediction of temperature histories during heat treatment (quenching and tempering), and stress analyses accounting for the thermo-mechanical history, including proof loading. The manufacturing conditions assumed for the models correspond to data obtained from a chain manufacturer. The predicted residual stress distribution is then combined with the fatigue stress range in service, due to either tension-tension loading or Out-of-Plane Bending (OPB). The effect of the residual stress distribution on the fatigue damage is discussed, and a sensitivity study on the assumptions used in the residual stress prediction is carried out. This determines for which loading conditions the modeling of the heat treatment stage can be neglected so that modeling of the proof loading step is sufficient for assessing the effect on fatigue life.

Theoretical prediction of residual stresses induced by cold spray with experimental validation

2019 ◽  
Vol 15 (3) ◽  
pp. 599-616 ◽  
Author(s):  
Dibakor Boruah ◽  
Xiang Zhang ◽  
Matthew Doré
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Cold Spray ◽  
Residual Stress Distribution ◽  
Thermal Mismatch ◽  
Individual Layer ◽  
Content Type ◽  
Layer Height ◽  
Proposed Model

PurposeThe purpose of this paper is to develop a simple analytical model for predicting the through-thickness distribution of residual stresses in a cold spray (CS) deposit-substrate assembly.Design/methodology/approachLayer-by-layer build-up of residual stresses induced by both the peening dominant and thermal mismatch dominant CS processes, taking into account the force and moment equilibrium requirements. The proposed model has been validated with the neutron diffraction measurements, taken from the published literature for different combinations of deposit-substrate assemblies comprising Cu, Mg, Ti, Al and Al alloys.FindingsThrough a parametric study, the influence of geometrical variables (number of layers, substrate height and individual layer height) on the through-thickness residual stress distribution and magnitude are elucidated. Both the number of deposited layers and substrate height affect residual stress magnitude, whereas the individual layer height has little effect. A good agreement has been achieved between the experimentally measured stress distributions and predictions by the proposed model.Originality/valueThe proposed model provides a more thorough explanation of residual stress development mechanisms by the CS process along with mathematical representation. Comparing to existing analytical and finite element methods, it provides a quicker estimation of the residual stress distribution and magnitude. This paper provides comparisons and contrast of the two different residual stress mechanisms: the peening dominant and the thermal mismatch dominant. The proposed model allows parametric studies of geometric variables, and can potentially contribute to CS process optimisation aiming at residual stress control.

A Further Study of Residual Stresses in Circumferential Welds

1973 ◽  
Vol 95 (4) ◽  
pp. 238-242 ◽  
Author(s):  
S. Vaidyanathan ◽  
H. Weiss ◽  
I. Finnie
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Base Metal ◽  
Filler Metal ◽  
Residual Stress Distribution ◽  
Experimental Results ◽  
Circumferential Welds ◽  
Single Pass ◽  
Full Penetration

The residual stress distribution for a circumferential weld between cylinders was obtained in a prior publication for a full penetration, single pass weld with no variation of alloy content across the weld. In the present work the approach is extended to cover a wider variety of weld conditions. It is shown that the effects of multipass welds, partial penetration welds, and welds with filler metal differing greatly in properties from the base metal can approximately be taken into account. Experimental results are presented to support the proposed method of analysis.

scholarly journals Separation of the Formation Mechanisms of Residual Stresses in LPBF 316L

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1234
Author(s):  
Alexander Ulbricht ◽  
Simon J. Altenburg ◽  
Maximilian Sprengel ◽  
Konstantin Sommer ◽  
Gunther Mohr ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Residual Stress Distribution ◽  
Formation Mechanisms ◽  
Micro Computed Tomography ◽  
Solidification Shrinkage ◽  
Stainless Steel 316L ◽  
Heat Accumulation ◽  
Cooling Rates

Rapid cooling rates and steep temperature gradients are characteristic of additively manufactured parts and important factors for the residual stress formation. This study examined the influence of heat accumulation on the distribution of residual stress in two prisms produced by Laser Powder Bed Fusion (LPBF) of austenitic stainless steel 316L. The layers of the prisms were exposed using two different border fill scan strategies: one scanned from the centre to the perimeter and the other from the perimeter to the centre. The goal was to reveal the effect of different heat inputs on samples featuring the same solidification shrinkage. Residual stress was characterised in one plane perpendicular to the building direction at the mid height using Neutron and Lab X-ray diffraction. Thermography data obtained during the build process were analysed in order to correlate the cooling rates and apparent surface temperatures with the residual stress results. Optical microscopy and micro computed tomography were used to correlate defect populations with the residual stress distribution. The two scanning strategies led to residual stress distributions that were typical for additively manufactured components: compressive stresses in the bulk and tensile stresses at the surface. However, due to the different heat accumulation, the maximum residual stress levels differed. We concluded that solidification shrinkage plays a major role in determining the shape of the residual stress distribution, while the temperature gradient mechanism appears to determine the magnitude of peak residual stresses.

scholarly journals Influence of Welding Defects on Residual Stresses: Numerical Study

2014 ◽  
Vol 996 ◽  
pp. 506-511
Author(s):  
Intissar Frih ◽  
Pierre Antoine Adragna ◽  
Guillaume Montay
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Numerical Study ◽  
Stress Gradient ◽  
Residual Stress Distribution ◽  
Welded Structure ◽  
Critical Defect ◽  
Welding Defects ◽  
Residual Stress Gradient

This paper presents a study on the application of the finite element methods to predict the influence of a defect on the residual stress distribution in a T-welded structure. A defect is introduced in a numerical model firstly without residual stress to see its impact (size and position) on the stress distribution. Secondly the most critical defect (determined previously) is simulated with a residual stress gradient. The obtained results are useful for computation stress concentration factor due to weld residual stresses.

Measurement of Residual Stresses in a Circular Ring Using the Successive Cracking Method

1996 ◽  
Vol 118 (2) ◽  
pp. 217-223 ◽  
Author(s):  
K. J. Kang ◽  
S. Y. Seol
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Circular Ring ◽  
Outer Edge ◽  
Residual Stress Distribution ◽  
Ring Specimen ◽  
Element Analysis ◽  
Theoretical Derivation ◽  
Sectioning Method

A method which we describe as the “successive cracking method” for measuring residual stresses in a circular ring is presented. In this method, the residual stresses are evaluated using a fracture mechanics approach. The strains measured at a point on the outer edge of the ring as a crack is introduced and extended from the edge are used to deduce the residual stress distribution in the uncracked ring. Finite element analysis is carried out to examine the validity of the theoretical derivation. Experiments to measure the residual stresses in a steel ring specimen are done by the successive cracking method. For comparison purposes, the experimental results using the sectioning method are presented as well. The successive cracking method is shown to be valid, simple, and effective for measuring the two-dimensional residual stress distribution in an axisymmetric member.

Residual Stress Relief in the Aluminium Alloy 7075

2017 ◽  
Vol 905 ◽  
pp. 31-39 ◽  
Author(s):  
Jeremy S. Robinson ◽  
Christopher E. Truman ◽  
Thilo Pirling ◽  
Tobias Panzner
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Neutron Diffraction ◽  
Residual Stresses ◽  
Aluminium Alloy ◽  
Stress Relief ◽  
Residual Stress Distribution ◽  
Cold Compression ◽  
Heat Treated ◽  
Minimum Residual

The residual stresses in heat treated 7075 aluminium alloy blocks have been characterised using two neutron diffraction strain scanning instruments. The influence of uniaxial cold compression (1-10%) on relieving the residual stress has been determined. Increasing the magnitude of cold compression from 1 to 10% has been shown to have a beneficial effect on the residual stress distribution by reducing the range between the maximum and minimum residual stresses. The effect of over aging 7075 on residual stress has also been characterised using neutron diffraction and this was found to reduce the residual stress by 25-40%. A relationship between {311} peaks widths and amount of cold compression was also observed.

Sign in / Sign up

Export Citation Format

Share Document