Experimental Effect of Cryogenic MQL Cutting 304 Stainless Steel

2014 ◽  
Vol 621 ◽  
pp. 3-8 ◽  
Author(s):  
Ai Dong He ◽  
Bang Yan Ye ◽  
Zi Yuan Wang
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
304 Stainless Steel ◽  
Depth Of Cut ◽  
Internal Cooling ◽  
Dry Cutting ◽  
High Speed Cutting ◽  
Chip Breaking ◽  
Minimal Quantity Lubrication ◽  
Minimal Quantity

Cryogenic MQL is a kind of green machining technology of the combination of cryogenic air and minimal quantity lubrication (MQL). The aim of this research is to determine if the cryogenic MQL technique in turning with Cutting tool with internal cooling structure gives some advantages in terms of tool life, surface roughness and cutting chip breaking. This paper reports the results obtained from turning tests, at one feed rates (0.12mm/r) and one depth of cut (0.4mm) and different cutting speeds (43m/min, 108m/min, 217m/min), and the results obtained show that using cryogenic MQL had some advantages in terms of tool wear, surface roughness and cutting chip breaking compared to using dry cutting and cryogenic air cutting. And the results obtained show that when cryogenic MQL and cryogenic air cutting were applied to high speed cutting, they had more advantages.

SURFACE ROUGHNESS OF MAGNESIUM ALLOY AZ91D IN HIGH SPEED MILLING

2016 ◽  
Vol 78 (6-9) ◽  
Author(s):  
Mohd Shahfizal Ruslan ◽  
Kamal Othman ◽  
Jaharah A.Ghani ◽  
Mohd Shahir Kassim ◽  
Che Hassan Che Haron
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Parameters ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Polishing Process ◽  
High Speed Cutting ◽  
Radial Depth

Magnesium alloy is a material with a high strength to weight ratio and is suitable for various applications such as in automotive, aerospace, electronics, industrial, biomedical and sports. Most end products require a mirror-like finish, therefore, this paper will present how a mirror-like finishing can be achieved using a high speed face milling that is equivalent to the manual polishing process. The high speed cutting regime for magnesium alloy was studied at the range of 900-1400 m/min, and the feed rate for finishing at 0.03-0.09 mm/tooth. The surface roughness found for this range of cutting parameters were between 0.061-0.133 µm, which is less than the 0.5µm that can be obtained by manual polishing. Furthermore, from the S/N ratio plots, the optimum cutting condition for the surface roughness can be achieved at a cutting speed of 1100 m/min, feed rate 0.03 mm/tooth, axial depth of cut of 0.20 mm and radial depth of cut of 10 mm. From the experimental result the lowest surface roughness of 0.061µm was obtained at 900 m/min with the same conditions for other cutting parameters. This study revealed that by milling AZ91D at a high speed cutting, it is possible to eliminate the polishing process to achieve a mirror-like finishing.

Investigation of Surface Characteristics and Chip Morphology in High Speed Cutting of Inconel718 Based on SHPB System

2019 ◽  
Author(s):  
Zengqiang Wang ◽  
Zhanfei Zhang ◽  
Wenhu Wang ◽  
Ruisong Jiang ◽  
Kunyang Lin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Surface Profile ◽  
Chip Morphology ◽  
Depth Of Cut ◽  
Machined Surface ◽  
High Speed Cutting

Abstract High speed cutting (HSC) technology has the characteristics of high material removal rates and high machining precision. In order to study the relationships between chip morphology and machining surface characteristic in high speed cutting of superalloy Inconel718. High-speed orthogonal cutting experiment are carried out by used a high speed cutting device based on split Hopkinson pressure bar (SHPB). The specimen surfaces and collected chips were then detected with optical microscope, scanning electron microscope and three-dimensional surface profile measuring instrument. The results show that within the experimental parameters (cutting speed from 8–16m/s, depth of cut 0.1–0.5mm), the obtained chips are sawtooth chips and periodic micro-ripple appear on the machined surface. With the cutting speed increases, machining surface roughness is decreases from 1.4 to 0.99μm, and the amplitude of periodic ripples also decreases. With the cutting depth increases, the machining surface roughness increases from 0.96 to 5.12μm and surface topography becomes worse. With the increase of cutting speed and depth of cut, the chips are transform from continues sawtooth to sawtooth fragment. By comparing the frequency of surface ripples and sawtooth chips, it is found that they are highly consistent.

Investigation on surface quality of high-speed cutting titanium alloy Ti6Al4V based on Split-Hopkinson pressure bar

2020 ◽  
Vol 234 (10) ◽  
pp. 1293-1301 ◽  
Author(s):  
Zhanfei Zhang ◽  
Zengqiang Wang ◽  
Wenhu Wang ◽  
Ruisong Jiang ◽  
Yifeng Xiong
Keyword(s):  
Surface Roughness ◽  
Surface Topography ◽  
Surface Quality ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Hopkinson Pressure Bar ◽  
High Speed Cutting ◽  
Pressure Bar

High-speed cutting technology has the characteristics of high material removal rate and excellent processing quality. To investigate the surface quality of high-speed cutting Ti6Al4V alloy, the orthogonal cutting experiment is the cutting device based on improved Split-Hopkinson pressure bar carried out with a cutting speed of about 7–16 m/s. Surface roughness, residual stress and three-dimensional surface topography are examined to characterize the surface quality. And the chip geometry parameters are measured to analyze the formation mechanism of surface topography. The result shows that cutting force and surface roughness increase rapidly with the increase in depth of cut. In the meantime, the periodic microwaves appeared on the machined surface, and their amplitudes increase with the increase in depth of cut. However, surface roughness, residual stress and microwave amplitude all decrease with the increase in cutting speed. Moreover, it is found that the evolution trend of chip thickness and surface roughness with cutting parameters is very similar. Therefore, it can be inferred that there is a strong relationship between surface topography and chip morphology.

Effect of Cutting Speed on Chip Fracture Strain in High Speed Cutting

2009 ◽  
Vol 626-627 ◽  
pp. 65-70
Author(s):  
Hui Ping Zhang ◽  
X.P. Ji ◽  
Jue Wang ◽  
Er Liang Liu
Keyword(s):  
High Speed ◽  
Fracture Strain ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Forecast System ◽  
Measuring Device ◽  
High Speed Cutting ◽  
Chip Breaking ◽  
Chip Fracture ◽  
On Chip

This paper deals with the effect of cutting speed on chip fracture strain in high speed cutting. Firstly, a chip-fracture-strain-measuring device is designed and made according to chip breaking principle. Secondly, experiments are performed by the chip-fracture-strain-measuring device. The experiment results show that chip fracture strain increases first and then diminishes as cutting speed increasing in high speed cutting while feedrate and depth of cut are constant values. Lastly, the effect of cutting speed on chip fracture strain is theoretically analysed from three main factors which affect chip fracture strain. The study above lays a theory and basis for future investigation of chip fracture strain of the other metals and for future investigation the mechanism and chip breaking forecast system of 3-D groove insert in high speed cutting.

The Effects of Cutting Parameters to the Surface Roughness in High Speed Cutting of Micro-Milling Titanium Alloy Ti-6Al-4V

2020 ◽  
Vol 846 ◽  
pp. 133-138
Author(s):  
Gandjar Kiswanto ◽  
Adrian Mandala ◽  
Maulana Azmi ◽  
Tae Jo Ko
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Weight Reduction ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Parameters ◽  
Micro Milling ◽  
Depth Of Cut ◽  
High Speed Cutting ◽  
Micro Scale

Micro-milling offers high flexibility by producing complex 3D micro-scale products. Weight reduction are one of the optimizations of the product that can make it stronger and more efficient nowadays. Titanium are the most commonly used for micro-scale products especially in biomedical industries because of the biocompatibility properties. Titanium alloys offers high strength with low density and high corrosion resistance that is suitable for weight reduction. This study aims to investigate the influence of high speed cutting parameters to the surface roughness in micromilling of titanium alloy Ti-6Al-4V as high speed cutting offers more productivity since producing more cutting length in the same time. experiments are carried out by micromilling process with variations in high speed cutting parameters of spindle speed and feed rate with a constant depth of cut using a carbide cutting tool of with a diameter of 1 mm. The machining results in the form of a 4 mm slot with a depth as the same as depth of cut, which then measures its surface roughness. It was found that higher feed rate that is followed by higher spindle speed will produce better surface roughness.

A Study of Minimal Quantity Lubrication with MWCNTs in Turning of AISI 304L Steel

2014 ◽  
Vol 625 ◽  
pp. 108-114 ◽  
Author(s):  
Wei Tai Huang ◽  
Hsun Heng Tsai ◽  
Der Ho Wu ◽  
Wei Tai Lee
Keyword(s):  
Surface Roughness ◽  
Cutting Temperature ◽  
Cutting Fluid ◽  
Dry Cutting ◽  
Aisi 304L ◽  
Thermal Wear ◽  
Minimal Quantity Lubrication ◽  
Minimal Quantity ◽  
304L Steel

This paper proposes a new lubricant environment when MWCNTs was used in MQL for AISI 304L in the turning machine. The effects of dry cutting, MQL cutting, and MWCNTs/MQL were compared to the surface roughness of work pieces, cutting temperature and the tool wear. In the past, the studies have shown that the MQL process can prolong tool life and improve surface accuracy in machining. The purpose of using MWCNTs suspensions is to increase the thermal conductivity of cutting fluid and to reduce the temperature during the cutting and decrease the thermal wear of tool simultaneously. The present study investigated the characterization of the MWCNTs was applied into MQL during the turning process of AISI 304L experimentally. The results showed that the MWCNTs will be a very good additive to MQL, not only with the benefits of improving surface roughness but also with ability of prolonging life of tool by reducing the cutting temperature in turning AISI 304L.

High Speed Milling of Ti6Al4V Alloy with Minimal Quantity Lubrication

2007 ◽  
Vol 329 ◽  
pp. 663-668 ◽  
Author(s):  
Wei Zhao ◽  
Ning He ◽  
Liang Li
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Tool Life ◽  
Cutting Forces ◽  
High Speed ◽  
High Speed Milling ◽  
Minimal Quantity Lubrication ◽  
Minimal Quantity ◽  
Titanium Alloy Ti6al4v ◽  
Cutting Speeds

Minimal quantity lubrication (MQL) machining has been accepted as a successful semi-dry application because of its environmentally friendly characteristics and satisfactory performance in practical machining operations. However, seldom investigation has been done in MQL machining of titanium alloy at high cutting speeds. In this paper, high speed milling experiments with MQL9 ml/h of oil in a flow of compressed air have been carried out for a widely used titanium alloy Ti6Al4V. Uncoated cemented carbide inserts have been applied in the experiments. Within the range of cutting speeds employed (190 m/min~300 m/min), the cutting performance of MQL has been investigated when peripheral milling the titanium alloy Ti6Al4V in terms of cutting forces, surface roughness, tool life and wear mechanism. The results show that, compared to dry machining, MQL machining brings about a significant reduction in cutting forces and surface roughness, and it also gives rise to a notably prolonged tool life.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Studying The Effect of a New Mixed Cutting Fluid on Surface Roughness

2020 ◽  
Vol 38 (11A) ◽  
pp. 1593-1601
Author(s):  
Mohammed H. Shaker ◽  
Salah K. Jawad ◽  
Maan A. Tawfiq
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Cutting Parameters ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Cutting Fluids ◽  
Machining Processes ◽  
Dry Cutting ◽  
Cutting Speeds

This research studied the influence of cutting fluids and cutting parameters on the surface roughness for stainless steel worked by turning machine in dry and wet cutting cases. The work was done with different cutting speeds, and feed rates with a fixed depth of cutting. During the machining process, heat was generated and effects of higher surface roughness of work material. In this study, the effects of some cutting fluids, and dry cutting on surface roughness have been examined in turning of AISI316 stainless steel material. Sodium Lauryl Ether Sulfate (SLES) instead of other soluble oils has been used and compared to dry machining processes. Experiments have been performed at four cutting speeds (60, 95, 155, 240) m/min, feed rates (0.065, 0.08, 0.096, 0.114) mm/rev. and constant depth of cut (0.5) mm. The amount of decrease in Ra after the used suggested mixture arrived at (0.21µm), while Ra exceeded (1µm) in case of soluble oils This means the suggested mixture gave the best results of lubricating properties than other cases.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Sign in / Sign up

Export Citation Format

Share Document