Structural Design and Analysis of Aluminum Dome for Caofeidian Coal Storage

2016 ◽  
Vol 710 ◽  
pp. 396-401 ◽  
Author(s):  
Ze Chao Zhang ◽  
Hong Bo Liu ◽  
Xiao Dun Wang ◽  
Xiang Yu Yan ◽  
Jing Hai Yu ◽  
...  
Keyword(s):  
Finite Element ◽  
Aluminum Alloys ◽  
Three Dimensional ◽  
Single Layer ◽  
Element Model ◽  
Internal Force ◽  
Structural Deformation ◽  
Mode Analysis ◽  
Finite Element Software ◽  
The Stability

The upper part of Caofeidian coal storage was approximately hemispherical aluminum shell, covered with aluminum alloys plate. The capsule was made of aluminum alloys material, and its span was 125 meters. In the design, according to TEMCOR joint, we used the finite element software MIDAS to build the accurate geometry models and calculation models of aluminum alloys single layer latticed dome structures. By the combination of constant loads, live loads, snow load, wind load, temperature effect and other working conditions, we summarized the consumption of aluminum of the structures, and studied the structural internal force, structural deformation and structural stiffness. In addition, the X and Y two different direction seismic dynamic load was applied to the structure. The structural seismic performance under two kinds of modes were studied through the structure mode analysis of the vibration frequency. The vierendeel dome and single layer dome were controlled by the stability. ANSYS three-dimensional frame element model were set up, and the eigenvalue buckling analysis was carried out. By the geometrical nonlinear finite element method, combining with initial imperfections and material nonlinear, we found out the stability coefficient and the weak parts of the structure.

Finite Element Analysis of the Effect of Surface Hardening Depth in Port Crane Wheel

2011 ◽  
Vol 291-294 ◽  
pp. 3282-3286 ◽  
Author(s):  
Jiang Wei Wu ◽  
Peng Wang
Keyword(s):  
Finite Element ◽  
Surface Hardening ◽  
Three Dimensional ◽  
Element Model ◽  
Contact Stresses ◽  
Numerical Results ◽  
Element Analysis ◽  
Finite Element Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In port crane industry, the surface hardening technique is widely used in order to improve the strength of wheel. But the hardening depth is chosen only by according to the experience, and the effect of different hardened depths is not studied theoretically. In this paper, the contact stresses in wheel with different hardening depth have been analyzed by applying three-dimensional finite element model. Based on this model, the ANSYS10.0 finite element software is used. The elastic wheel is used to verify the numerical results with the Hertz’s theory. Three different hardening depths, namely 10mm, 25mm and whole hardened wheel, under three different vertical loads were applied. The effect of hardening depth of a surface hardened wheel is discussed by comparing the contact stresses and contact areas from the numerical results.

scholarly journals Modeling inflatable fabric with undevelopable surfaces by motion folding method

2019 ◽  
Vol 14 ◽  
pp. 155892501988640
Author(s):  
Xiao-Shun Zhao ◽  
He Jia ◽  
Zhihong Sun ◽  
Li Yu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Numerical Study ◽  
Technical Problem ◽  
Three Dimensional ◽  
Element Model ◽  
Model Errors ◽  
Folding Model ◽  
Study Results ◽  
The Stability

At present, most space inflatable structures are composed of flexible inflatable fabrics with complex undevelopable surfaces. It is difficult to establish a multi-dimensional folding model for this type of structure. To solve this key technical problem, the motion folding method is proposed in this study. First, a finite element model with an original three-dimensional surface was flattened with a fluid structure interaction algorithm. Second, the flattened surface was folded based on the prescribed motion of the node groups, and the final folding model was obtained. The fold modeling process of this methodology was consistent with the actual folding processes. Because the mapping relationship between the original finite element model and the final folding model was unchanged, the initial stress was used to modify the model errors during folding process of motion folding method. The folding model of an inflatable aerodynamic decelerator, which could not be established using existing folding methods, was established by using motion folding method. The folding model of the inflatable aerodynamic decelerator showed that the motion folding method could achieve multi-dimensional folding and a high spatial compression rate. The stability and regularity of the inflatable aerodynamic decelerator numerical inflation process and the consistency of the inflated and design shapes indicated the reliability, applicability, and feasibility of the motion folding method. The study results could provide a reference for modeling complex inflatable fabrics and promote the numerical study of inflatable fabrics.

Three-Dimensional Seismic Analysis on Reactor Structure

2010 ◽  
Author(s):  
Naibin Jiang ◽  
Feng-gang Zang ◽  
Li-min Zhang ◽  
Chuan-yong Zhang
Keyword(s):  
Finite Element ◽  
Large Scale ◽  
Seismic Analysis ◽  
Three Dimensional ◽  
Element Model ◽  
Earthquake Excitation ◽  
Finite Element Software ◽  
Reactor Structure ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The seismic analysis on reactor structure was performed with a new generation of finite element software. The amount of freedom degree of the model was more than twenty millions. The typical responses to operational basis earthquake excitation were given. They are larger than those with two-dimensional simplified finite element method, and the reasons of this phenomenon were analyzed. The feasibility of seismic analysis on large-scale three-dimensional finite element model under existing hardware condition was demonstrated, so some technological reserves for dynamic analysis on complicated equipments or systems in nuclear engineering are provided.

scholarly journals Influence of Backfill Compaction on Mechanical Characteristics of High-Density Polyethylene Double-Wall Corrugated Pipelines

2019 ◽  
Vol 2019 ◽  
pp. 1-24 ◽  
Author(s):  
Hongyuan Fang ◽  
Peiling Tan ◽  
Bin Li ◽  
Kangjian Yang ◽  
Yunhui Zhang
Keyword(s):  
Finite Element ◽  
High Density Polyethylene ◽  
Three Dimensional ◽  
Local Buckling ◽  
Element Model ◽  
High Density ◽  
Model Matching ◽  
Exterior Wall ◽  
Finite Element Software ◽  
Hdpe Pipe

For flexible pipelines, the influence of backfill compaction on the deformation of the pipe has always been the focus of researchers. Through the finite element software, a three-dimensional soil model matching the exterior wall corrugation of the high-density polyethylene pipe was skillfully established, and the “real” finite element model of pipe-soil interaction verified the accuracy through field test. Based on the model, the strain distribution at any position of the buried HDPE pipe can be obtained. Changing the location and extent of the loose backfill, the strain and radial displacement distributions of the interior and exterior walls of the HDPE pipe under different backfill conditions when external load applied to the foundation were analyzed, and the dangerous parts of the pipe where local buckling and fracture may occur were identified. It is pointed out that when the backfill is loose, near the interface between the backfill loose region and the well-compacted region, the maximum circumferential strain occurs frequently, the exterior wall strain is more likely to increase greatly on the region near crown or invert, the interior wall strains increase in amplitude at springline, and the location of the loose region has a greater influence on the strain of the pipe than the size of the loose area.

Mechanical Performance Analysis of Petroleum Derrick Substructure

2011 ◽  
Vol 105-107 ◽  
pp. 2121-2124
Author(s):  
Jun Feng Pei ◽  
Sheng Ying Deng ◽  
Guang Min Chen ◽  
Jian Zhang
Keyword(s):  
Finite Element ◽  
Mechanical Performance ◽  
Three Dimensional ◽  
Element Model ◽  
Structural Testing ◽  
Static Properties ◽  
Finite Element Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Project Structure

In recent years, the self-elevating derrick substructure which with the characteristics of easy to install、remove and transfer are gradually replacing layer box, box block substructure, etc. The three-dimensional finite element model of the MXD-701 jack-up derrick and substructure, which is used to analyze static properties of the petroleum substructure under the six different working loads are built by the ANSYS finite element software. Meanwhile, the wireless structural testing system（STS-WiFi）is testing at the MXD-701 petroleum substructure. Then comparing of the model results and testing results. Analysis results indicate that the stress of the substructure at the two beam table is greatest, the stress of the upper part of the guy column is much greater, and others are low, but in general, the overall substructure can fit the requirements of the strength and intensity. The compared results can accurately reflect the project structure of the stress and strain. Then, we can get the capacity of the substructure in order to provide evidence to the security situation of the substructure. It will have great significance to enrich and develop the mast base design and safety assessment theory.

BIOMECHANICAL STABILITY OF THE CERVICAL SPINE AFTER UNCINATE PROCESS RESECTION: A FINITE ELEMENT ANALYSIS

2015 ◽  
Vol 15 (06) ◽  
pp. 1540049 ◽  
Author(s):  
XUEFENG BO ◽  
XI MEI ◽  
HUI WANG ◽  
WEIDA WANG ◽  
ZAN CHEN ◽  
...  
Keyword(s):  
Finite Element ◽  
Cervical Spine ◽  
Equivalent Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Uncinate Process ◽  
Total Deformation ◽  
Maximum Equivalent Stress ◽  
Left And Right ◽  
The Stability

When performing anterolateral foraminotomy for the treatment of cervical spondylotic radiculopathy, the extent of uncinate process resection affects the stability of the cervical spine. The aim of this study was to determine the stability of the cervical spine after resection of various amounts of the uncinate process. Based on computed tomography (CT) scans of an adult male volunteer, a three-dimensional geometric model of the cervical spine (C4-C6) was established using Mimics 13.1, SolidWorks 2012, and ANSYS 15.0 software packages. Next, the mechanical parameters of the tissues were assigned according to their different material characteristics. Using the tetrahedral mesh method, a three-dimensional finite element model of the cervical spine was then established. In modeling uncinated process resection, two excision protocols were compared. The first excision protocol, protocol A, mimicked the extent of resection used in current clinical surgical practice. The second excision protocol, protocol B, employed an optimal resection extent as predicted by the finite element model. Protocols A and B were then used to resect the left uncinate process of the C5 vertebra to either 50% or 60% of the total height of the uncinate process. The stability of the cervical spine was assessed by evaluating values of deformation and maximum equivalent stress during extension, flexion, lateral bending, and rotation. After protocol A resection, the total deformation was increased as was the maximum equivalent stress during left and right rotation. After protocol B resection, the total deformation was little changed and the maximum equivalent stress was visibly decreased during left and right rotation. As evidenced by these results, protocol B resection had relatively little effect on the stability of the cervical spine, suggesting that resection utilizing the limits proposed in protocol B appears to better maintain the stability of the cervical spine when compared with current clinical surgical practice as replicated in protocol A.

Numerical Simulation of Ultimate of Slings for Three-Tower and Four-Span Suspension Bridge under Tanker Fire

2013 ◽  
Vol 361-363 ◽  
pp. 1187-1193
Author(s):  
Mu Yu Liu ◽  
Wei Tian ◽  
Ying Wang ◽  
Wu Jing
Keyword(s):  
Finite Element ◽  
Failure Time ◽  
Three Dimensional ◽  
Fire Risk ◽  
Suspension Bridge ◽  
Element Model ◽  
Prevention Measures ◽  
Heating Curve ◽  
Finite Element Software ◽  
Three Dimensional Finite Element

Three-dimensional finite element model of Yingwuzhou Yangtze river bridge was established by using the finite element software ANSYS. Since the characteristics of bridge fire differed much from that of buildings, Heating curve HCincwas selected as heating curve caused by tanker fire. Heat loading was imposed on the middle of main span where the tanker fire had taken place of three-tower and four-span suspension bridge . The temperature field and stress, modulus of elasticity, strength of sling changing with time caused by tanker burning in midspan were systematically investigated to obtain the failure time of the sling. The calculation also compared the above results of HCinccurve with that of ISO834 curve. This research can provide some references to fire risk prevention measures of bridge during its service life.

Investigation of Bearing Characteristics of High-Cap Pile Foundation under Inclined Load

2018 ◽  
Vol 777 ◽  
pp. 559-563
Author(s):  
Yu Zhuo Jia ◽  
Guo Zheng Sun ◽  
Chang Qing Li ◽  
Long Long Tian
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Pile Foundation ◽  
Yellow River ◽  
Three Dimensional ◽  
Pile Group ◽  
Element Model ◽  
Inclined Load ◽  
Finite Element Software ◽  
Inclined Angle

To analyze the characteristics of bearing capacity of high-cap pile foundation under inclined load and investigate the influence of vertical and horizontal component on the foundation at different loading angles, based on the background of the Yellow River Crossing project, a three-dimensional finite element model of high-cap foundation is simulated and analyzed with the finite element software ABAQUS. The conclusions are shown as follows: Under the same displacement condition, when the load inclination angle α from 0°(horizontal load) to 80°, the horizontal direction bearing capacity of the foundation increases from 684.8kN to 759.9kN, increases by 10.97%. Expands of vertical load component will affect the pile group effect, the shear force of the back row piles increases with the load inclined angle.

RESEARCH ON WIND PERFORMANCE AND FIELD EXPERIMENT OF LARGE SCALE COMPLEX SURFACE SPACE TRUSS WITH STEEL PIPE

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Xiuli Wang ◽  
Yonghong Ran ◽  
Huvue Zhang ◽  
Yanpeng Zhu
Keyword(s):  
Finite Element ◽  
Large Scale ◽  
Canopy Structure ◽  
Field Tests ◽  
Complex Surface ◽  
Element Model ◽  
Internal Force ◽  
Wind Load ◽  
Large Span ◽  
Finite Element Software

The wind-induced performance response of large-span truss curved roofs is extremely complex and changes obviously under wind load. This paper has taken the large-span steel roof of Liu Zhaike highway toll station as an example to analyze by both numerical simulations and field tests of responses of the steel canopy under wind load. In this case, simulated analysis results using finite element software were calibrated and verified by the field test results. In addition, a new method of large structure field testing was proposed which obtained the internal force and displacement of the canopy structure. Moreover, this paper analyzed and determined the actual stress state of the rectangular pipe truss. Finally, the safety condition of the roof was evaluated based on the monitoring data and the simulation of the finite element model. And the analysis methods provides references for similar engineering field tests, as well as guidance for the operation and maintenance for this project.

Stability Analysis of Stiffened Plates Based on State-Vector Equation

2013 ◽  
Vol 671-674 ◽  
pp. 1561-1569
Author(s):  
Yan Li Wang ◽  
Guang Hui Qing
Keyword(s):  
Finite Element ◽  
State Vector ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Stiffened Plates ◽  
Variation Principle ◽  
Element Formulation ◽  
Vector Equation ◽  
Finite Element Software ◽  
The Stability

Firstly, based on the theory of state-vector equation, the semi-analysis finite element formulation for the stability of the plates under various boundary conditions was derived by modified Hellinger-Reissner (H-R) variation principle for the elastic material. Secondly, the three-dimensional models for the stability of stiffened plates were established. The semi-analytical solution of state equation for the stability of stiffened plates are proved to be efficient and accurate by comparing with the exact solutions of references and the numerical solutions of the finite element software through several examples.

Sign in / Sign up

Export Citation Format

Share Document