Mechanical Properties and Phase Morphology of Poly(Lactic Acid)/Acrylonitrile-Butadiene Rubber/Organoclay Nanocomposites Prepared by Melt Blending

2018 ◽  
Vol 775 ◽  
pp. 13-19
Author(s):  
Sirirat Wacharawichanant ◽  
Kasana Chomphunoi ◽  
Chawisa Wisuttrakarn ◽  
Manop Phankokkruad
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Impact Strength ◽  
Phase Morphology ◽  
Poly Lactic Acid ◽  
Butadiene Rubber ◽  
Melt Blending ◽  
Acrylonitrile Butadiene Rubber ◽  
Internal Mixer ◽  
The Impact

This work investigated the mechanical properties and phase morphology of poly(lactic acid) (PLA)/acrylonitrile-butadiene rubber (NBR) blends and nanocomposites, which prepared by melt blending in an internal mixer. The contents of NBR were 5, 10, 15 and 20 wt% and the content of organoclay was 3 phr. The impact test showed that the impact strength of PLA/NBR blends increased with an increase of NBR content and the impact strength of the blends was more than eight times by adding NBR 10 wt% when compared with neat PLA. The tensile test showed that Young’s modulus and tensile strength of PLA/NBR blends and nanocomposites decreased after adding NBR and organoclay. While the strain at break of the NBR blends increased with increasing NBR content. This result is attributed to the rubber phase in NBR in a cause the increment of elongation and elasticity in PLA/NBR blends. The morphology of PLA/NBR blends observed the fractured surface was rougher than that of pure PLA. This observation indicates that the addition of NBR in PLA can change the brittle fracture of PLA to ductile fracture, which has an effect to the strain at break or elongation of PLA. However, the morphology of the PLA/NBR blends were also observed the phase separation of the dispersed NBR phase and PLA matrix phase, and appeared the voids in a polymer matrix. The addition of organoclay had an effect slightly on the morphology of the blends. From X-ray diffraction, results found that PLA/organoclay and PLA/NBR/organoclay nanocomposites showed the intercalated structure, which PLA chains were inserted into the interlayer of clay due to the increase of d-spacing.

Improvement of Poly(Lactic Acid) Properties by Using Acrylonitrile-Butadiene Rubber and Polyethylene-g-Maleic Anhydride

2019 ◽  
Vol 972 ◽  
pp. 178-184
Author(s):  
Sirirat Wacharawichanant ◽  
Chawisa Wisuttrakarn ◽  
Kasana Chomphunoi ◽  
Manop Phankokkruad
Keyword(s):  
Lactic Acid ◽  
Thermal Properties ◽  
Maleic Anhydride ◽  
Thermal Degradation ◽  
Impact Strength ◽  
Mass Loss ◽  
Poly Lactic Acid ◽  
Butadiene Rubber ◽  
Acrylonitrile Butadiene Rubber ◽  
The Impact

This research prepared poly(lactic acid) (PLA) and PLA/acrylonitrile-butadiene rubber (NBR) blends before and after adding polyethylene-g-maleic anhydride with 3 wt% of maleic anhydride (PE-g-MA3) 3 phr. The effects of NBR and PE-g-MA3 on morphological, mechanical and thermal properties of PLA and PLA blends were discussed. The morphological analysis observed the two-phase morphology of PLA/NBR blends, and it was observed the cavities generated due to NBR phase detachment during sample fracture, and droplets of NBR phase at higher NBR content. The PE-g-MA3 addition could improve adhesion between PLA and NBR phases due to the decrease of cavities in PLA matrix and droplet size of NBR. The mechanical properties showed the impact strength and strain at break of PLA/NBR blends dramatically increased when the amount of NBR increasing. The addition of PE-g-MA3 significantly improved the impact strength of PLA/NBR blends. The thermal properties showed the NBR addition had effect slightly on the melting temperature of PLA/NBR blends. The filling of NBR and PE-g-MA3 greatly decreased the percent crystallinity of PLA more than two times. The thermal degradation of pure PLA and NBR proceeds by one step, while the thermal degradation process of PLA/NBR and PLA/PE-g-MA3 proceeds by two steps. Which the first step showed a large mass loss of PLA degradation and the second step showed a small mass loss of PE-g-MA and NBR degradation.

scholarly journals A review on graft compatibilizer for thermoplastic elastomer blend

2021 ◽  
Vol 2080 (1) ◽  
pp. 012003
Author(s):  
K.K. Nitiyah ◽  
Luqman Musa ◽  
M.S.M. Rasidi ◽  
Shayfull Zamree Abd Rahim ◽  
Rozyanty Rahman ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Natural Rubber ◽  
Thermoplastic Elastomer ◽  
Synthetic Polymers ◽  
The Other ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Internal Mixer ◽  
The Impact ◽  
Elastomer Blend

Abstract A biodegradable thermoplastic elastomer (TPE) blend is developed by blending poly (lactic acid) (PLA) and natural rubber (NR) or epoxidized natural rubber (ENR) and it is a sustainable substitution in recent years for synthetic polymers. PLA is high in mechanical strength and compostable, but it is highly stiff and brittle. The incorporation of NR or ENR to PLA increases the impact strength and toughness of PLA. However, the disparity in polarity between PLA and elastomer phase like NR and ENR results in TPE blend being incompatible. Hence, compatibilization is essential to improve its polarity and develop interactions. Compatibilizer that composed of two different polymer is known is graft compatibilizer with the aid of grafting agent. The graft compatibilizers are divided into two categories. The first type is made up of one polymer and grafting agent and, the other one is composed of two polymer groups and grafting agent. These two types of graft compatibilizer can be prepared via two different method such as direct melt blending and solution. Apart from this, the TPE blend is produced via the melt blending technique with mixing machines such as internal mixer and extruder. This article has reviewed the preparation of the graft compatibilizer and blending technique of TPE. Based on the findings, the graft compatibilizers has a significant role in improving miscibility and compatibility across blend composed of different phase.

Effects of Poly(Methyl Methacrylate)-Encapsulated Nanosilica on Mechanical Properties of Poly(Lactic Acid)/Ethylene Vinyl Acetate Nanocomposites

2018 ◽  
Vol 773 ◽  
pp. 51-55
Author(s):  
Jasmine Pongkasem ◽  
Saowaroj Chuayjuljit ◽  
Phasawat Chaiwutthinan ◽  
Amnouy Larpkasemsuk ◽  
Anyaporn Boonmahitthisud
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Impact Strength ◽  
Methyl Methacrylate ◽  
Tensile Properties ◽  
Vinyl Acetate ◽  
Ethylene Vinyl Acetate ◽  
Poly Lactic Acid ◽  
Poly Methyl Methacrylate ◽  
The Impact

In this study, poly(lactic acid) (PLA) was melt mixed with three weight percentages (10–30wt%) of ethylene vinyl acetate copolymer (EVA) in an internal mixer, followed by a compression molding. According to a better combination of mechanical properties, the 90/10 (w/w) PLA/EVA was selected for preparing hybrid nanocomposites with three loadings (1, 3 and 5 parts per hundred of resin , phr) of poly(methyl methacrylate)-encapsulated nanosilica (PMMA-nSiO2). The nanolatex of PMMA-nSiO2 was synthesized via in situ differential microemulsion polymerization. The obtained PMMA-nSiO2 showed a core-shell morphology with nSiO2 as a core and PMMA as a shell, having an average diameter of 43.4nm. The influences of the EVA and PMMA-nSiO2 on the impact strength and the tensile properties of the PLA/EVA nanocomposites were studied and compared. It is found that the impact strength and the tensile properties of the 90/10 (w/w) PLA/EVA were improved with the appropriate amounts of the EVA and PMMA-nSiO2.

Comparison of Morphology and Mechanical Properties of Polyoxymethylene/Cellulose and Poly(Lactic Acid)/Cellulose Composites

2018 ◽  
Vol 916 ◽  
pp. 19-23 ◽  
Author(s):  
Sirirat Wacharawichanant ◽  
Nisarat Wimonsupakit ◽  
Sasithorn Kuhaudomlap
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Microscopy Study ◽  
Electron Microscopy Study ◽  
Poly Lactic Acid ◽  
Melt Mixing ◽  
Cellulose Composites ◽  
Internal Mixer ◽  
The Impact ◽  
Morphology And Mechanical Properties

The objective of this study is to fabricate the polyoxymethylene (POM)/microcrystalline cellulose (MCC) and poly(lactic acid) (PLA)/MCC composites, and to compare the effect of MCC on the morphology and mechanical properties of POM and PLA. The polymer composites were prepared by melt mixing in an internal mixer and molded by compression molding. The MCC concentrations were 1, 3, 5, 7, 10, 15 and 10% by weight. From scanning electron microscopy study observes the fracture surface of POM and PLA composites is much rough and the roughness increases with increasing MCC content. This observation indicates MCC induces the ductile fracture characteristic of POM and PLA. The addition of MCC can improve the impact strength of PLA composite and improve Young’s modulus of both POM and PLA composites. While the tensile strength and strain at break decrease after adding MCC. In summary, MCC can enhance the morphology and mechanical properties of PLA composites is better than POM composites.

Morphology and Mechanical Properties of Poly (Lactic Acid) and Acrylonitrile-Butadiene Rubber Blends with Organoclay

2016 ◽  
Vol 835 ◽  
pp. 284-288 ◽  
Author(s):  
Sirirat Wacharawichanant ◽  
Chawisa Wisuttrakarn ◽  
Kasana Chomphunoi
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Poly Lactic Acid ◽  
Butadiene Rubber ◽  
Melt Mixing ◽  
Rubber Blends ◽  
Acrylonitrile Butadiene Rubber ◽  
Electron Microscopy Analysis ◽  
Surface Modified ◽  
Morphology And Mechanical Properties

The effects of the montmorillonite clay surface modified with 25-30 wt% of methyl dihydroxyethyl hydrogenated tallow ammonium (Clay-MHA) on morphology and mechanical properties of poly(lactic acid) (PLA)/acrylonitrile-butadiene rubber copolymer (NBR)/Clay-MHA composites were investigated. The composites of blends of PLA/NBR with Clay-MHA were prepared by melt mixing in an internal mixer and molded by compression molding. The ratio of PLA and NBR was 80/20 by weight and the Clay-MHA content was 1, 3, 5 and 7 phr. The results showed Young’s modulus and stress at break of the composites increased with increasing Clay-MHA content. While the tensile strength and strain at break of the composites decreased with increasing Clay-MHA content. Scanning electron microscopy analysis showed that the addition of Clay-MHA could improve the miscibility of PLA and NBR to be homogeneous blends and the pore in polymer blends was disappeared.

Synergistic effects in mechanical properties of PLA/PCL blends with optimized composition, processing, and morphology

RSC Advances ◽  
2015 ◽  
Vol 5 (120) ◽  
pp. 98971-98982 ◽  
Author(s):  
Aleksandra Ostafinska ◽  
Ivan Fortelny ◽  
Martina Nevoralova ◽  
Jiri Hodan ◽  
Jana Kredatusova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Impact Strength ◽  
Synergistic Effects ◽  
Poly Lactic Acid ◽  
The Individual ◽  
The Impact

Blending of poly(lactic acid) with poly(ε-caprolactone) can increase the impact strength above the values of the individual components.

Effects of Processing Parameters and Nanofillers on Mechanical and Thermal Properties and Morphology of Impact Modified Poly (lactic acid)

2013 ◽  
Vol 1499 ◽  
Author(s):  
Eda Acik ◽  
Ulku Yilmazer
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Impact Strength ◽  
Random Copolymer ◽  
Processing Parameters ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Injection Molded ◽  
The Impact

ABSTRACTTernary nanocomposites of poly (lactic acid) (PLA) were produced by melt blending with two types of elastomers and five types of organoclays to obtain improved mechanical properties such as tensile strength, modulus and impact strength. One of the elastomers is a random copolymer of ethylene and glycidyl methacrylate (E-GMA) and the other one is a random terpolymer of ethylene-butyl acrylate-maleic anhydride (E-BA-MAH). Organically modified montmorillonites (OMMT) were utilized as nanofillers. XRD, DSC, tensile and impact tests were done on the injection molded samples. FTIR, SEM and TEM analyses are still in progress. As preliminary results, thermal analysis showed that the addition of compatibilizers and organoclays does not have a distinct effect on the thermal properties of the composites, and no evidence of nucleation activity of compatibilizers or organoclays was found. For all types of organoclays, the nanocomposites produced with E-GMA exhibited better mechanical properties in comparison to nanocomposites containing E-BA-MAH, especially for the impact strength.

scholarly journals The effect of dynamic vulcanization on the morphological and mechanical properties of the toughened poly (lactic acid)/epoxidized natural rubber

2018 ◽  
Vol 14 (3) ◽  
pp. 348-352 ◽  
Author(s):  
Nur Amira Sahirah Abdullah ◽  
Zurina Mohamad
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Impact Strength ◽  
Natural Rubber ◽  
Crosslinking Agent ◽  
Epoxidized Natural Rubber ◽  
Poly Lactic Acid ◽  
Dynamic Vulcanization ◽  
The Impact

Poly (lactic acid)/epoxidized natural rubber (PLA/ENR) was prepared by using counter-rotating twin-screw extruder. For dynamic vulcanization process, ENR was compounded with 3 phr of N, N’-m-phenylenebismaleimide (HVA-2) as a crosslinking agent. The aim of this study is to determine the effect of unvulcanized and dynamically vulcanized of ENR on the properties of PLA/ENR blend. The blending of PLA with ENR was prepared with the various composition of ENR (0 wt% to 30 wt%). The morphology and mechanical properties of the blends were investigated by using scanning electron microscope (SEM), tensile test, and impact test. The unvulcanized blend produced a co-continuous morphology of PLA and ENR and the dynamically vulcanized blend shows the dispersed ENR rubber particles in PLA continuous matrix.  For both systems, the tensile strength value was dropped with the increasing amount of ENR content. The impact strength of both systems shows the maximum value at 20 wt% of ENR content. However, dynamically vulcanized PLA/ENR blend shows a better tensile strength and impact strength value as compared with unvulcanized blend.

Study on the Mechenical Properties of PPC/PLA Blends Modified by POSS

2013 ◽  
Vol 741 ◽  
pp. 28-32 ◽  
Author(s):  
Yi Chen ◽  
Yue Peng ◽  
Wen Yong Liu ◽  
Guang Sheng Zeng ◽  
Xiang Gang Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Impact Strength ◽  
Rheological Properties ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Aliphatic Polycarbonate ◽  
Thermal Stability Of

Aliphatic polycarbonate Polycarbonate/poly (lactic acid)/(PPC/PLA) blends were prepared by melt blending, 1,2-propanediol isobutyl POSS (P-POSS) were added into the blends as a compatilizer and reinforcer. The morphologies, mechanical properties and rheological properties of blends were investigated systematically. The results showed that the adding of P-POSS could improve the compatibilization of PPC and PLA obviously. The thermal stability of the blends was enhanced but the crystallization was effected slightly. Moreover, the tensile strength and impact strength of blends exhibited a considerably increase.

Sign in / Sign up

Export Citation Format

Share Document