Processing and Characterization of Amorphous Copper Oxide Thin Films Prepared by Reactive Magnetron Sputtering

2018 ◽  
Vol 775 ◽  
pp. 238-245 ◽  
Author(s):  
Thitinai Gaewdang ◽  
Ngamnit Wongcharoen
Keyword(s):  
Thin Films ◽  
Low Temperature ◽  
Magnetron Sputtering ◽  
Copper Oxide ◽  
Flow Rate ◽  
Localized States ◽  
Positive Sign ◽  
Variable Range Hopping ◽  
Variable Range ◽  
Deposited Films

In this paper, copper oxide (CuOx) thin films with amorphous phase were prepared on glass substrates by reactive dc magnetron sputtering. The influence of the flow rate of O2 on the structural, optical and electrical properties of the as-deposited films was systematically studied. XRD revealed that the as-deposited films remained amorphous in the whole range of adjusted oxygen flow rate. Surface morphology and nanoparticle size of the films were observed by AFM. Electrical resistivity and Hall effect measurements were performed on the films with van der Pauw configuration. The positive sign of the Hall coefficient confirmed the p-type conductivity in all studied films. From temperature-dependent electrical conductivity of the films prepared at R(O2) of 1.5 sccm, it was show that three types of behavior can be expected, nearest-neighbor hopping at high temperature range (200-300 K), the Mott variable range hopping at low temperature (110-190 K) and Efros-Shklovskii variable range hopping at very low temperature (65-100 K). Some important parameters corresponding to Mott-VRH and ES-VRH like density of localized states near the Fermi level, localization length, degree of disorder, hopping distance and hopping energy were determined. These parameters would be helpful for optimizing the performance of photovoltaic applications.

scholarly journals Effect of rapid thermal annealing on structural and optical properties of ZnS thin films fabricated by RF magnetron sputtering technique

2019 ◽  
Vol 14 (1) ◽  
pp. 53-63 ◽  
Author(s):  
M. S. Bashar ◽  
Rummana Matin ◽  
Munira Sultana ◽  
Ayesha Siddika ◽  
M. Rahaman ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Carrier Concentration ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealing Temperature ◽  
Annealing Treatment ◽  
Localized States ◽  
Stoichiometric Ratio ◽  
Deposited Films

AbstractThe ZnS thin films have been deposited by radio frequency magnetron sputtering at room temperature. Post-deposition rapid thermal annealing treatment was done for the films deposited at different powers ranging from 70 to 100 W. One peak is observed for as-deposited and annealed thin films at around 28.48° corresponding to the (111) reflection plane indicating a zincblende structure. The overall intensity of the peaks and the FWHM values of as-deposited films increased after annealing corresponding to the increase in crystallinity. The optical energy bandgap is found in the range of 3.24–3.32 eV. With increasing annealing temperature, the decrease in the Urbach energy values indicating a decrease in localized states which is in good agreement with the XRD results where the crystallinity increased. The surface morphology of the films seems to be composed of Nano-granules with a compact arrangement. Apparently, the grain size increases in the deposited films as annealing temperature increases. The compositional ratio attained close to the stoichiometric ratio of 1:1 after annealing. From the Hall effect measurement, the carrier concentration and mobility are found to increase after annealing. The high carrier concentration and mobility also comply with structural and optical analysis. Best results are found for the film annealed at 400 °C deposited at 90 W.

SixCy Thin Films Deposited at Low Temperature by DC Dual Magnetron Sputtering: Effect of Power Supplied to Si and C Cathode Targets on Film Physicochemical Properties

2012 ◽  
Vol 717-720 ◽  
pp. 197-201 ◽  
Author(s):  
Henrique S. Medeiros ◽  
Rodrigo S. Pessoa ◽  
Júlio C. Sagás ◽  
Mariana A. Fraga ◽  
Lúcia V. Santos ◽  
...  
Keyword(s):  
Thin Films ◽  
Low Temperature ◽  
Magnetron Sputtering ◽  
Stoichiometric Ratio ◽  
Power Sources ◽  
Temperature Growth ◽  
Plasma Sputtering ◽  
Dc Power ◽  
Film Bulk ◽  
Deposited Films

A DC dual magnetron sputtering system with graphite (C) and silicon (Si) targets was used to grow stoichiometric and non-stoichiometric silicon carbide (SixCy) thin films at low temperature. Two independently DC power sources were used to enable the total discharge power be shared, under certain proportions, between the Si and C magnetron cathodes. The motivation was to control the sputtering rate of each target so as to vary the stoichiometric ratio x/y of the deposited films. The species content, thickness and chemical bonds of as-deposited SixCy films were studied by Rutherford backscattering spectroscopy (RBS), profilometry analysis and Fourier transform infrared absorption (FTIR), respectively. Overall, the present work reveals a new reliable plasma sputtering technique for low temperature growth of amorphous SixCy thin films with the capability of tuning the degree of formation of a-SiC, a-Si and a-C bonds in the film bulk.

Mott variable range hopping transport in thermal evaporated vanadyl 2, 3 naphthalocyanine thin films

2021 ◽  
pp. 125029
Author(s):  
I. Dhanya ◽  
Malathy Krishnan ◽  
Reny Renji ◽  
M.K. Anu ◽  
Rachel G. Varghese ◽  
...  
Keyword(s):  
Thin Films ◽  
Variable Range Hopping ◽  
Hopping Transport ◽  
Variable Range

Structure and Electrical Properties of Pulsed Laser Deposited Amorphous Carbon Nitride Thin Films

2002 ◽  
Vol 750 ◽  
Author(s):  
Yoshifumi Aoi ◽  
Kojiro Ono ◽  
Kunio Sakurada ◽  
Eiji Kamijo
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Electrical Properties ◽  
Photoelectron Spectroscopy ◽  
Pulsed Laser ◽  
Film Surface ◽  
Input Power ◽  
Localized States ◽  
Active Nitrogen ◽  
Deposited Films

ABSTRACTAmorphous CNx thin films were deposited by pulsed laser deposition (PLD) combined with a nitrogen rf radical beam source which supplies active nitrogen species to the growing film surface. The deposited films were characterized by X-ray photoelectron spectroscopy (XPS), Raman scattering, and Fourier transform infrared (FTIR) spectroscopy. Nitrogen content of the deposited films increased with increasing rf input power and N2 pressure in the PLD chamber. The maximum N/C ratio 0.23 was obtained at 400 W of rf input power and 1.3 Pa. XPS N 1s spectra shows the existence of several bonding structures in the deposited films. Electrical properties of the deposited films were investigated. The electrical conductivity decreased with increasing N/C atomic ratio. Temperature dependence of electrical conductivity measurements indicated that electronic conduction occurred by variable-range hopping between p electron localized states.

Sign in / Sign up

Export Citation Format

Share Document