Durability Studies of Environmental Friendly Self Compacting Concrete with and without Fiber

2019 ◽  
Vol 803 ◽  
pp. 207-215
Author(s):  
L.V. Prasad Meesaraganda ◽  
Nilanjan Tarafder
Keyword(s):  
Construction Industry ◽  
Construction Cost ◽  
Target Strength ◽  
Fine Aggregate ◽  
Acid Attack ◽  
Self Compacting Concrete ◽  
Chloride Permeability ◽  
River Sand ◽  
Concrete Production ◽  
Quarry Dust

Concrete is the most important building material in construction industry because of its revolutionary property of quick hardening and free from internal problems. Its use has a great effect on environment due to the large amount of natural resources and cement lime materials required for manufacture the concrete structures. Now it’s the time for think in the direction of Eco-friendly durable materials in concrete production. In the present work, Quarry Dust and Foundry Sand are partial replaced River Sand to develop Rheological and Durability properties of M40 grade of Eco-Efficient Self-Compacting Concrete (ESCC). The target strength could be achieved satisfying the rheological properties of Eco-Efficient Self-Compacting Concrete with fiber additions. In this study investigations carried to find the Permeability, Shrinkage, Acid attack and Rapid Chloride Permeability Test (RCPT) of Eco-Efficient Fiber based Self-Compacting Concrete and it is observed that it is no way inferior to the conventional concretes. From the experimentation, it is recommended that waste materials from different source are fitting to be used as fine materials in concrete. The construction cost reduces by utilising such waste as fine aggregate in place of aggregate from natural source for construction.

scholarly journals COMPARING THE FLEXURAL STRENGTH OF CONCRETE MADE WITH RIVER SAND WITH THAT MADE WITH QUARRY DUST AS FINE AGGREGATE

2018 ◽  
Vol 6 (6) ◽  
pp. 453-460
Author(s):  
Chijioke C ◽  
Nwaiwu ◽  
Aginam ◽  
Anyadiegwu
Keyword(s):  
Flexural Strength ◽  
Concrete Beams ◽  
Target Strength ◽  
Fine Aggregate ◽  
River Sand ◽  
Minimum Value ◽  
Maximum Value ◽  
Quarry Dust ◽  
Good Substitute

This work focuses on the 100% replacement of river sand with quarry dust in the production of concrete. Two types of concrete were produced (concrete made with river sand and that made with quarry dust as fine aggregate), the concretes produces were cast into beams and cured for 28 days. The flexural strengths of the concrete beams cast was determine at 28 day strength. At 28 days target strength the maximum flexural strength of concrete made with river sand as fine aggregate is 5.375111N/mm2 and minimum flexural strength is 2.2155N/mm2, for the concrete made with quarry dust as fine aggregate the maximum flexural strength is 2.567 N/mm2. The maximum value of 2.567 N/mm2 for concrete made with quarry dust as fine aggregate is higher than the minimum value of 2.2155N/mm2 for concrete made with river sand as fine aggregate. With this result it shows that quarry dust is a good substitute to river sand in the production of concrete.

Physical and Mechanical Properties of Concrete Incorporating Manufactured Sand

2015 ◽  
Vol 1115 ◽  
pp. 160-165
Author(s):  
Maisarah Ali ◽  
Muhammad Hariz Nordin ◽  
Siti Asmahani Saad
Keyword(s):  
Construction Industry ◽  
Physical And Mechanical Properties ◽  
Sem Analysis ◽  
Target Strength ◽  
Sieve Analysis ◽  
Fine Aggregate ◽  
Compressive Test ◽  
River Sand ◽  
Manufactured Sand ◽  
Concrete Mix

Concrete is a common material that widely used in construction industry. Excessive usage of this material causes exhaustibility to its components, especially fine aggregate or sand. In this regard, the use of manufactured sand is considered as a part of the solutions to fix this problem as it is readily available. In this research, the manufactured sand is used at 40%, 50% and 60% to replace natural river sand. SEM analysis reveals the rough surface texture of manufactured sand. The manufactured sand has angular shape and sieve analysis reveled that it has a considerable amount of fine particle. Slump test shows that concrete using manufactured sand pass the standard. On the other hand, compressive test shows that concrete cubes using manufactured sand do not achieved the target strength. Water absorptive test on the cubes revealed that M-Sand I has higher absorptivity property compared to river sand . SEM analysis revealed the existance of microcrack as well as porosity in in concrete cubes incorporating of manufactured sand. It can be concluded that it can be concluded that the higher the percentage of manufactured sand in the concrete mix the lower is the comprensive strength.

scholarly journals Utilisation of Seasand as Partial Replacement of Fine Aggregrate to Strengthen the Concrete

2020 ◽  
Vol 9 (5) ◽  
pp. 891-894
Keyword(s):  
Construction Industry ◽  
Coarse Aggregate ◽  
Construction Material ◽  
Strength Properties ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
River Sand ◽  
Sea Sand ◽  
Quarry Dust

Concrete is an important construction material widely used in the construction industry nowadays. It is blended material consisting of cement, fine aggregate, coarse aggregate and water. Generally the use of river sand as fine aggregate in our country is very widespread in industry. This paper mainly focuses on the study of strength properties of concrete in which river sand is replaced with sea sand as fine aggregate. In addition to it, Quarry Dust when added gains strength. Different mix proportions was replaced partially in 5%, 10%, 15% by Sea sand and Quarry dust. The strength of concrete for various mix proportions are carried out and tested for 14, 28, 56 days of curing. From the results obtained, with the replacement of river sand by sea sand along with well graded quarry dust upto to 15% increases the strength of concrete.

scholarly journals Effects of Partial Replacement of Fine Aggregate with Quarry Dust on Concrete Properties

2020 ◽  
Vol 4 (1) ◽  
Author(s):  
S.O Ajamu ◽  
I.A Raheem ◽  
S.B Attah ◽  
J.O Onicha
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Replacement Level ◽  
River Sand ◽  
Split Tensile Strength ◽  
Stone Dust ◽  
Concrete Production ◽  
Quarry Dust

Natural river sand is one of the important constituent materials in concrete production while stone dust is a material obtained from crusher plants which is also sometimes being used either partially or fully in replacement of natural river sand in concrete production. Use of stone dust in concrete not only improves the quality of concrete but also conserve the natural river sand. However, due its scarcity and environmental degradation caused resulting from excessive mining of Natural river sand, there is need to investigate an alternative material of the same quality which can replace river sand in concrete production. In the present study, experiments were carried out to study the gradation of aggregates, workability, compressive strength and split tensile strength of concrete made using quarry dust as replacement of fine aggregate at 0, 25, 50, 75, and 100%. Grade M15 of concrete was produced with ordinary Portland cement (OPC) for referral concrete while M25 of concrete was prepared for compressive strength and split tensile strength concrete. Workability and Compressive strength were determined at different replacement level of fine aggregate and optimum replacement level was determined based on compressive strength. Results showed that by replacing 50% of fine aggregate with quarry dust, concrete of maximum compressive strength can be produced as compared to all other replacement levels. The effect of quarry dust on compressive strength and split tensile strength was investigated and from the overall result obtained, it was observed that the compressive strength and split tensile strength increased significantly for all the curing ages from 0% to 50% replacement level of quarry dust. Maximum value obtained for 28day compressive and tensile strength were 25N/mm2 and 2.3N/mm2 respectively and this occurred at 50% replacement.

scholarly journals Compression and Split Tensile Characteristics of Concrete Containing Quarry Residues

2019 ◽  
Vol 5 (5) ◽  
pp. 1-5
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Research Facility ◽  
River Sand ◽  
Split Tensile Strength ◽  
Fine Aggregates ◽  
Concrete Production ◽  
The World ◽  
Substitute Material ◽  
Quarry Dust

Waterway sand and pit sand are the most normally utilized fine aggregates for concrete creation in many parts of the world. Huge scale extraction of these materials presents genuine ecological risk in numerous parts of the nation. Aside from the ecological danger, there still exists the issue of intense lack in many regions. In this way, substitute material in place of river sand for concrete production should be considered. The paper means to examine the compressive and split tensile qualities of concrete produced using quarry residue, sand, and a blend of sand and quarry dust. The experimentation is absolutely research facility based. A total of 60 concrete cubes of size 150 mm x 150 mm x 150 mm, and 60 cylinders 150 mm in diameter and 300 mm deep, conforming to M50 grade were casted. All the samples were cured and tested with a steady water/concrete proportion of 0.31. Out of the 60 blocks cast, 20 each were made out of natural river sand, quarry dust and an equivalent blend of sand and quarry dust. It was discovered that the compressive strength and split tensile strength of concrete produced using the blend of quarry residue and sand was higher than the compressive qualities of concrete produced using 100% sand and 100% quarry dust.

scholarly journals Comparison of Conventional Concrete and Replacement of River Sand by Waste Foundry Sand and Cement by Nano-Silica

2020 ◽  
pp. 201-205
Keyword(s):  
Experimental Investigation ◽  
Compressive Strength ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Nano Silica ◽  
River Sand ◽  
Conventional Concrete ◽  
Foundry Sand ◽  
Concrete Production ◽  
Waste Foundry Sand

This paper presents an experimental investigation on the properties of concrete in which like cement is partially replacing by used nano silica and is partially replacing by used waste foundry sand. Because now a day the world wide consumption of sand as cement and as fine aggregate in concrete production is very high. Nano silica and waste foundry sand are major by product of casting industry and create land pollution. The cement will be replaced with nano silica and the river sand will be replaced with waste foundry sand (0%, 5%, 10%, 15%, 20%). This experimental investigation was done and found out that with the increase in the nano silica and waste foundry sand ratio. Compression test has been done to find out the compressive strength of concrete at the age of 7, 14, 21, and 28. Test result indicates in increasing compressive strength of plain concrete by inclusion of nano silica as a partial replacement of cement and waste foundry sand as a partial replacement of fine aggregate.

Strength of concrete produced with different sources of aggregates from selected parts of Abia and Imo States of Nigeria

2020 ◽  
Vol 18 (5) ◽  
pp. 1053-1061
Author(s):  
Uchechi G. Eziefula ◽  
Hyginus E. Opara ◽  
Bennett I. Eziefula
Keyword(s):  
Compressive Strength ◽  
Target Strength ◽  
Fine Aggregate ◽  
River Sand ◽  
Content Type ◽  
Coarse Aggregates ◽  
Crushed Granite ◽  
Stone Concrete ◽  
Different Sources ◽  
Practical Implications

Purpose This paper aims to investigate the 28-day compressive strength of concrete produced with aggregates from different sources. Design/methodology/approach Coarse aggregates were crushed granite and natural local stones mined from Umunneochi, Lokpa and Uturu, Isuakwato, respectively, in Abia State, Nigeria. Fine aggregate (river sand) and another coarse aggregate (river stone) were dredged from Otammiri River in Owerri, Imo State, Nigeria. The nominal mix ratios were 1:1:2, 1:2:4 and 1:3:6, whereas the respective water–cement ratios were 0.45, 0.5, 0.55 and 0.6. Findings The compressive strength of granite concrete, river stone concrete and local stone concrete ranged 17.79-38.13, 15.37-34.57 and 14.17-31.96 N/mm2, respectively. Compressive strength was found to increase with decreasing water–cement ratio and increasing cement content. Practical implications Granite concrete should be used in reinforced-concrete construction, especially when a cube compressive strength of 30 N/mm2 or higher is required. Originality/value Granite concrete exceeded the target compressive strength for all the concrete specimens, whereas river stone concrete and local stone concrete failed to achieve the target strength for some mix proportions and water–cement ratios.

scholarly journals Suitability of Scoria as Fine Aggregate and Its Effect on the Properties of Concrete

2019 ◽  
Vol 11 (17) ◽  
pp. 4647 ◽  
Author(s):  
Warati ◽  
Darwish ◽  
Feyessa ◽  
Ghebrab
Keyword(s):  
Construction Materials ◽  
Energy Utilization ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Test Results ◽  
River Sand ◽  
Conventional Concrete ◽  
Efficient Energy ◽  
Concrete Production

The increase in the demand for concrete production for the development of infrastructures in developing countries like Ethiopia leads to the depletion of virgin aggregates and high cement demand, which imposes negative environmental impacts. In sustainable development, there is a need for construction materials to focus on the economy, efficient energy utilization, and environmental protections. One of the strategies in green concrete production is the use of locally available construction materials. Scoria is widely available around the central towns of Ethiopia, especially around the rift valley regions where huge construction activities are taking place. The aim of this paper is therefore to analyze the suitability of scoria as a fine aggregate for concrete production and its effect on the properties of concrete. A differing ratio of scoria was considered as a partial replacement of fine aggregate with river sand after analyzing its engineering properties, and its effect on the mechanical properties of concrete were examined. The test results on the engineering properties of scoria revealed that the material is suitable to be used as a fine aggregate in concrete production. The replacement of scoria with river sand also enhanced the mechanical strength of the concrete. Generally, the findings of the experimental study showed that scoria could replace river sand by up to 50% for conventional concrete production.

Suitability of Quarry Dust as a Partial Replacement of Fine Aggregate in Self Compacting Concrete

2018 ◽  
Vol 877 ◽  
pp. 248-253
Author(s):  
Thete Swapnil Tanajirao ◽  
D. Arpitha ◽  
Suman Saha ◽  
C. Rajasekaran
Keyword(s):  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Self Compacting Concrete ◽  
Slump Flow ◽  
Fine Aggregates ◽  
Material Gain ◽  
Optimum Utilization ◽  
Hardened Properties ◽  
Quarry Dust

Large quantity of the quarry dust gets produced annually in the quarries during the extraction of the crushed coarse aggregate. As a result, disposal problems of this material gain significant momentum as these disturb environmental systems also. Now-a-days many of the countries like India is facing problems of ban on the extraction of sand and lacunae in procuring of fine aggregate, which is important constituent of the concrete. To overcome this problem, present study is focused on the suitability to utilize the quarry dust in Self Compacting Concrete (SCC) partially as fine aggregate with the natural fine aggregates. In this work, quarry dust is used as replacement of sand in a different level (0%, 15%, 30%, 45% and 60%) for producing the SCC. Fresh properties such as slump flow and V-funnel time have been measured for all mixes and hardened properties as compressive strength, splitting tensile strength and flexural strength of the concrete have been checked for all the mixes and it has been found that optimum utilization of quarry dust up to 30% can been done to produce SCC without compromising with its properties.

scholarly journals Evaluating Optimum Strength of Geopolymer Concrete using Quarry Rock Dust with inclusion of natural and hybrid fibers under ambient curing

2020 ◽  
Vol 9 (6) ◽  
pp. 1-5
Keyword(s):  
Construction Industry ◽  
Glass Fibers ◽  
Strength Properties ◽  
Waste Materials ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Hybrid Fibers ◽  
River Sand ◽  
Rock Dust

Conventionally used cement –a primary binder also a necessitate element in producing concrete rates first in the construction industry. Production of conventional cement requires a greater skill and is energy intensive. The usage of waste materials in the production of concrete and reduction in cement content was only the possible alternative in the past decade. Associated risks with the production of Ordinary Portland Cement are well known. A greener aided with a natural friendly claim can be made only with the usage of the waste materials and reduction in evolving respiration gas to the atmosphere. Almost all works are carried out using source material fly ash, with fine aggregate and coarse aggregate. Concrete plays a vital role in the construction industry and on the other hand, river sand; one of the essential material has become very expensive which is a scarce material. Depletion of sand is a hectic issue due to increased usage of sand in construction. No other replacement materials such as quarry rock dust is not concentrated in casting geopolymer specimens. Even though in some research papers the replacement materials are added only in partial replacement without aiming on 100% replacement. Many researches mainly focus towards test results of GPC specimens using steel fibers, glass fibers. But the study related to natural fibers and hybrid fibers are found scarce. The main part of this work aimed at characterizing the engineering strength properties of geopolymer concrete by 100% replacement of fine aggregate with quarry rock dust. Hence, combination of flyash and quarry rock dust in GPC have been considered for evaluating the mechanical properties of geopolymer concrete. Also, investigation focuses on incorporation of three different fibers namely polypropylene fibers(PF), coir fibers(CF) and hybrid fibers(HF) in different percentage of proportions such as 0.5%,1%,and 1.5% to determine the maximum strength properties of GPC.

Sign in / Sign up

Export Citation Format

Share Document