Investigation of PLA-PEG-45S5 Bioactive Glass Composite Enhancement on Bioactivity

2020 ◽  
Vol 833 ◽  
pp. 214-219
Author(s):  
Nik Syahirah Aliaa Nik Sharifulden ◽  
Siti Noor Fazliah Mohd Noor ◽  
Siti Fatimah Samsurrijal ◽  
Siti Nur Liyana Ramlee ◽  
Nur Syazana Azizan
Keyword(s):  
Thermal Analysis ◽  
Bioactive Glass ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Degradation Study ◽  
Significant Difference ◽  
Biomaterial Science ◽  
Materials Used ◽  
Hdf Cells

Bioactivity is an important aspect in biomaterial science ensuring materials used are safe for clinical application. The study describes fabrication of composites containing polylactic acid (PLA) – polyethylene glycol (PEG) with incorporation of sol-gel derived 45S5 bioactive glass (BG). Thermal analysis via Differential Thermal Analysis shows a favorable point over degree of crystallization that influence cells attachment, although non-significant difference in values indicates BG has homogenously dispersed. This correlates to X-ray diffraction analysis where non-significant difference is seen in intensities of the diffraction peaks, which confirms low impact of BG brittleness properties over the fabricated composite. Composites’ pH and degradation study in Simulated Body Fluid shows a steady increment profile over time and lower degradation rate for the composite after incorporation of BG. In vitro cell proliferation study also showed that HDF cells seeded on composite film of P/BG2.5 exhibit highest cell viability with steady increment of proliferation throughout the observation period.

AP40 Bioactive Glass Ceramic by Sol-Gel Synthesis: In Vitro Dissolution and Cell-Mediated Bioresorption

2013 ◽  
Vol 541 ◽  
pp. 41-50 ◽  
Author(s):  
Ilaria Cacciotti ◽  
Giorgia Lehmann ◽  
Antonella Camaioni ◽  
Alessandra Bianco
Keyword(s):  
Bioactive Glass ◽  
Human Peripheral Blood ◽  
Sol Gel ◽  
Blood Monocytes ◽  
X Ray Diffraction ◽  
Degradation Behaviour ◽  
Dissolution Tests ◽  
Different Temperatures ◽  
Sol Gel Synthesis

In this work, the sol-gel synthesis of AP40 bioactive glass system was reported. The obtained powder was fully characterised in terms of microstructure, composition and thermal behaviour by X-ray diffraction (XRD) measurements, Fourier transform infrared (FT-IR) spectroscopy, thermogravimetry and differential thermal analysis (TG-DTA).In vitrodissolution tests were performed in order to assess the degradation behaviour of sol-gel derived AP40 samples thermally treated at different temperatures. Finally, preliminary results on cytocompatibility are reported, based on bioresorption activity of human peripheral blood monocytes differentiated into osteoclasts on sintered disks.

scholarly journals In VitroBioactivity and Antimicrobial Tuning of Bioactive Glass Nanoparticles Added with Neem (Azadirachta indica) Leaf Powder

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
M. Prabhu ◽  
S. Ruby Priscilla ◽  
K. Kavitha ◽  
P. Manivasakan ◽  
V. Rajendran ◽  
...  
Keyword(s):  
Bioactive Glass ◽  
Azadirachta Indica ◽  
Sol Gel ◽  
Sem Analysis ◽  
Microbial Infection ◽  
X Ray Diffraction ◽  
Doped Glasses ◽  
Leaf Powder ◽  
Doped Glass

Silica and phosphate based bioactive glass nanoparticles (58SiO2-33CaO-9P2O5) with doping of neem (Azadirachta indica) leaf powder and silver nanoparticles were prepared and characterised. Bioactive glass nanoparticles were produced using sol-gel technique.In vitrobioactivity of the prepared samples was investigated using simulated body fluid. X-ray diffraction (XRD) pattern of prepared glass particles reveals amorphous phase and spherical morphology with a particle size of less than 50 nm. When compared to neem doped glass, better bioactivity was attained in silver doped glass through formation of hydroxyapatite layer on the surface, which was confirmed through XRD, Fourier transform infrared (FTIR), and scanning electron microscopy (SEM) analysis. However, neem leaf powder doped bioactive glass nanoparticles show good antimicrobial activity againstStaphylococcus aureusandEscherichia coliand less bioactivity compared with silver doped glass particles. In addition, the biocompatibility of the prepared nanocomposites reveals better results for neem doped and silver doped glasses at lower concentration. Therefore, neem doped bioactive glass may act as a potent antimicrobial agent for preventing microbial infection in tissue engineering applications.

Luminescent Properties of Zn2SiO4:Eu3+,Dy3+ Phosphors via Sol-Gel Process

2012 ◽  
Vol 217-219 ◽  
pp. 733-736
Author(s):  
Xiu Mei Han ◽  
Shu Ai Hao ◽  
Ying Ling Wang ◽  
Gui Fang Sun ◽  
Xi Wei Qi
Keyword(s):  
Thermal Analysis ◽  
Ir Spectra ◽  
Sol Gel ◽  
Luminescent Properties ◽  
Photoluminescence Spectra ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sol Gel Process ◽  
Ft Ir

Zn2SiO4:Eu3+, Dy3+ phosphors have been prepared through the sol-gel process. X-ray diffraction (XRD), thermogravimetric and ddifferential thermal analysis (TG-DTA), FT-IR spectra and photoluminescence spectra were used to characterize the resulting phosphors. The results of XRD indicated that the phosphors crystallized completely at 1000oC. In Zn2SiO4:Eu3+,Dy3+ phosphors, the Eu3+ and Dy3+ show their characteristic red(613nm, 5D0-7F2), blue (481nm, 4F9/2–6H15/2) and yellow (577nm, 4F9/2–6H13/2) emissions.

Thermal analysis and in vitro bioactivity of bioactive glass–alumina composites

2011 ◽  
Vol 62 (1) ◽  
pp. 118-129 ◽  
Author(s):  
Xanthippi Chatzistavrou ◽  
Nikolaos Kantiranis ◽  
Eleana Kontonasaki ◽  
Konstantinos Chrissafis ◽  
Labrini Papadopoulou ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Bioactive Glass ◽  
In Vitro Bioactivity ◽  
Alumina Composites

Fabrication and Characterization of Sol-Gel Derived PZT/WO3 Ceramics

2008 ◽  
Vol 55-57 ◽  
pp. 369-372 ◽  
Author(s):  
T. Sreesattabud ◽  
Anucha Watcharapasorn ◽  
Sukanda Jiansirisomboon
Keyword(s):  
Lead Zirconate Titanate ◽  
Sol Gel ◽  
Rhombohedral Phase ◽  
Lead Zirconate ◽  
X Ray Diffraction ◽  
Calcination Process ◽  
Materials Used ◽  
Phase Characterization ◽  
Gel Processing

Lead zirconate titanate/tungsten oxide (PZT/WO3) ceramics were prepared from the powders synthesized by a modified triol sol-gel processing method. In this study, the starting materials used for synthesis of PZT-sol were zirconium (IV) propoxide, titanium (IV) isopropxide, lead (II) acetate trihydrate and 1,1,1,- tris (hydroxymethyl) ethane. To prepare PZT/xWO3 powders (where x = 0, 0.5, 1 and 3 wt%), nano-sized WO3 was ultrasonically dispersed and mixed with the PZT sol, dried and calcined at 600°C for 4 h. X-ray diffraction results indicated that fully crystallized powders were obtained. Phase characterization suggested that at high WO3 concentration, the reaction between PZT and WO3 occurred during the calcination process. To prepare PZT/xWO3 ceramics, the powders were pressed and sintered at 1100°C for 6 h. Phase characterization by XRD indicated that the content of WO3 significantly affected tetragonal-to-rhombohedral phase transition. Microstructure of thermally etched samples showed that increasing the content of WO3 decreased grain size of the ceramics.

scholarly journals The Effect of the Bioactive Glass and the Er:YAG Laser on the Remineralization of the Affected Dentin: A Comparative In Vitro Study

2020 ◽  
Vol 11 (2) ◽  
pp. 160-166
Author(s):  
Mohammad Javad Moghaddas ◽  
Horieh Moosavi ◽  
Sara Yaghoubirad ◽  
Nasim Chiniforush
Keyword(s):  
Bioactive Glass ◽  
In Vitro Study ◽  
Control Group ◽  
Dentinal Tubule ◽  
Glass Ionomer ◽  
Significant Difference ◽  
Post Hoc ◽  
Caries Lesions ◽  
Cavity Floor

Introduction: The purpose of this study was to compare the effect of the bioactive glass, the glass ionomer, and the Erbium YAG laser as liners on the remineralization of the affected dentin. Methods: The present study was conducted on 64 healthy extracted human molars divided into 4 groups, 1 control group and 3 experimental groups. After artificially inducing dentinal caries lesions, each of the experimental groups was applied to the cavity floor and then restored with a composite. The samples were stored after thermocycling in an incubator for two months. Finally, the hardness of the cavity floor was measured at 3 depths of 20, 50 and 100 μm by the Vickers microhardness tester. The dentin conditions underneath the liners were also evaluated with FESEM. Statistical analysis was performed by two-way ANOVA and the post-hoc Games-Howell test (P<0.05). Results: Among the groups, the lowest microhardness value was in the control group (P<0.05) except at a depth of 100 μm; therefore, there was no significant difference between the control group and the bioactive glass (P>0.05). The laser group had the highest microhardness value, which was significantly different from the control group (P<0.05). There was a significant difference between the laser and bioactive glass (P<0.05), except at a depth of 20 μm. The laser and glass ionomer had only a significant difference at a depth of 100 μm (P<0.05). The microhardness value induced by glass ionomer was higher than bioactive glass, which in no depth was significant (P>0.05). Partial dentinal tubule occlusion was observed with FESEM in each of the experimental groups as compared to the control group. Conclusion: The microhardness values were higher in all groups than in the control group. The laser might be more successful in remineralization than the other ones.

scholarly journals Properties of Composite Materials Used for Bracket Bonding

2013 ◽  
Vol 24 (3) ◽  
pp. 279-283 ◽  
Author(s):  
Ana Caroline Silva Gama ◽  
Andre Guaraci de Vito Moraes ◽  
Lilyan Cardoso Yamasaki ◽  
Alessandro Dourado Loguercio ◽  
Ceci Nunes Carvalho ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Stress Test ◽  
Flexural Modulus ◽  
Significant Difference ◽  
Contraction Stress ◽  
Materials Used ◽  
Flowable Composites

The purpose of this study was to evaluate in vitro the shear bond strength to enamel, flexural strength, flexural modulus, and contraction stress of one orthodontic composite and two flowable composites. Orthodontic brackets were bonded to 45 human maxillary premolars with the composites Transbond XT, Filtek Z-350 flow and Opallis flow and tested for shear bond strength. For measurement of flexural strength and flexural modulus, specimens were fabricated and tested under flexion. For the contraction stress test, cylindrical specimens were tested and an extensometer determined the height of the specimens. The data were subjected to one-way ANOVA and Tukey's test (α=0.05). The shear bond strength values were significantly lower (p<0.05) for the flowable composites compared with the orthodontic composite. For the flexural strength, no statistically significant difference was found among the composites (p>0.05) while the flexural modulus was significantly higher (p<0.05) for Transbond XT than for Filtek Z-350 flow and Opallis flow. The orthodontic composite presented significantly lower contraction stress values than the flowable composites (p<0.05). The light-activated orthodontic composite material presented higher flexural modulus and shear bond strength and lower contraction stress than both flowable composites.

Phase Formation Kinetics in Sol-Gel Derived Strontium Bismith Tantalate

2001 ◽  
Vol 666 ◽  
Author(s):  
Yun-Mo Sung ◽  
Woo-Chul Kwack
Keyword(s):  
Activation Energy ◽  
Thermal Analysis ◽  
Phase Formation ◽  
Sol Gel ◽  
Avrami Exponent ◽  
Fluorite Phase ◽  
X Ray Diffraction ◽  
Aurivillius Phases ◽  
Formation Kinetics ◽  
Isothermal Kinetic

ABSTRACTPhase formation characteristics of Sr0.7Bi2.4Ta2O9 (SBT) powder, synthesized via sol-gel and pyrolysis process, was investigated by using thermal analysis. Each of the two exotherms, appearing in differential thermal analysis (DTA) scan curves, was identified as crystallization of fluorite phase and transformation of fluorite to aurivillius phase, respectively by using x-ray diffraction (XRD). By applying non-isothermal kinetic analyses to the DTA results, activation energy values for the formation of fluorite and aurivillius phases were determined as 192 and 375 kJ/mol, respectively and Avrami exponent values for each reaction were determined as 0.91 and 0.96, respectively. These activation energy and Avrami exponent values were discussed in detail to understand phase formation mechanism in SBT system.

Study on the Synthesis of Nano-Crystalline Mg2SiO4 Powders by Aqueous Sol-Gel Process

2013 ◽  
Vol 538 ◽  
pp. 142-145 ◽  
Author(s):  
X.F. Chen ◽  
J. Li ◽  
T.T. Feng ◽  
Y.S. Jiang ◽  
X.H. Zhang ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Sol Gel ◽  
Magnesium Nitrate ◽  
Metal Alkoxides ◽  
X Ray Diffraction ◽  
Calcination Process ◽  
X Ray ◽  
Nano Crystalline ◽  
Sol Gel Process ◽  
Scanning Electron

The forsterite-structure Mg2SiO4 was successfully synthesized by the aqueous sol-gel method using Si sols dioxide and magnesium nitrate as starting materials instead of expensive organic solvent and metal alkoxides. The as-prepared nanopowders were characterized by X-ray diffraction (XRD), differential thermal analysis (DTA) and scanning electron microscope (SEM), respectively. The results showed that the calcination process of gel consisted of a series of oxidation and combustion reactions, accompanied by significantly exothermal effects. Highly reactive nanosized Mg2SiO4 powders were successfully obtained at 850 °C with particle size of 60~80 nm.

Sign in / Sign up

Export Citation Format

Share Document