Optimization of Structure of Soft Block for Design of Adaptive Polyurethanes

2020 ◽  
Vol 869 ◽  
pp. 273-279
Author(s):  
Marina A. Gorbunova ◽  
Denis V. Anokhin ◽  
Valentina A. Lesnichaya ◽  
Alexander A. Grishchuk ◽  
Elmira R. Badamshina
Keyword(s):  
Mutual Influence ◽  
Glycol Adipate ◽  
Mass Ratio ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Crystallization Conditions ◽  
Crystalline Domains ◽  
Kinetics Of

A synthesis of new di-and triblock polyurethane thermoplastic copolymers containing different mass ratio of two crystallizing blocks - poly (1,4-butylene glycol) adipate and poly-ε-caprolactone diols was developed. Using combination of danamometric analysis, IR-spectroscopy, differential scanning calorimetry and X-ray diffraction, the effect of the soft block composition and crystallization conditions on crystal structure and thermal behavior of the obtained polymers have been studied. For the triblock copolymers we have shown a possibility of control the kinetics of material hardening and final mechanical characteristics due to the mutual influence of polydiols during crystallization. In the result, the second crystallizing component allows to control amount, structure and quality of crystalline domains in polyurethanes by variation of crystallization conditions.

scholarly journals Synthesis, Characterization, and Thermal Kinetics of Mixed Gadolinium: Calcium Heptamolybdate System

2014 ◽  
Vol 2014 ◽  
pp. 1-9
Author(s):  
R. K. Koul ◽  
Shivani Suri ◽  
Vishal Singh ◽  
K. K. Bamzai
Keyword(s):  
Grown Crystal ◽  
Frequency Factor ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Relevant Model ◽  
X Ray ◽  
Thermoanalytical Techniques ◽  
Thermal Kinetics ◽  
Symmetry Structure ◽  
Kinetics Of

Synthesis of mixed gadolinium calcium heptamolybdate (GdCaHM) system in silica gel medium using single gel single tube technique has been successfully achieved. The grown crystal exhibits various morphologies, which includes spherulites, multifaceted, and square platelets. The nature of the grown material was established by X-ray diffraction (XRD) studies. Fourier transform infrared spectroscopy (FTIR) study signifies the presence of heptamolybdate (Mo7O24) and water symmetry structure, whereas energy dispersive X-ray analysis (EDAX) establishes the stoichiometric of the grown crystal as GdCaMo7O24·8H2O. The thermal behaviour was studied using the thermoanalytical techniques, which include thermogravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Results obtained on the application of TG based models, namely, Horowitz-Metzger, Coats-Redfern, and Piloyan-Novikova, suggest the contracting cylindrical model as the relevant model for the thermal decomposition of the material. The kinetic parameters, namely, the order of reaction (n), activation energy (Ea), frequency factor (Z), and entropy (ΔS*), were also calculated using these three models.

scholarly journals Hydrogen desorption kinetics of MgH2 synthesized from modified waste magnesium

2014 ◽  
Vol 32 (3) ◽  
pp. 385-390
Author(s):  
Aysel Kantürk Figen ◽  
Bilge Coşkuner ◽  
Sabriye Pişkin
Keyword(s):  
Hydrogen Desorption ◽  
Nitrogen Atmosphere ◽  
Desorption Kinetics ◽  
X Ray Diffraction ◽  
Heating Rates ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Xrf Scanning ◽  
Isothermal Kinetic ◽  
Kinetics Of

AbstractIn the present study, hydrogen desorption properties of magnesium hydride (MgH2) synthesized from modified waste magnesium chips (WMC) were investigated. MgH2 was synthesized by hydrogenation of modified waste magnesium at 320 °C for 90 min under a pressure of 6 × 106 Pa. The modified waste magnesium was prepared by mixing waste magnesium with tetrahydrofuran (THF) and NaCl additions, applying mechanical milling. Next, it was investigated by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM) and Brunauer-Emmett-Teller (BET) techniques in order to characterize its structural properties. Hydrogen desorption properties were determined by differential scanning calorimetry (DSC) under nitrogen atmosphere at different heating rates (5, 10, and 15 °C/min). Doyle and Kissenger non-isothermal kinetic models were applied to calculate energy (Ea) values, which were found equal to 254.68 kJ/mol and 255.88 kJ/mol, respectively.

On the Mechanism of Milling Induced Disordering in AlFe

1996 ◽  
Vol 460 ◽  
Author(s):  
M. T. Clavaguera-Mora ◽  
J. Zhu ◽  
M. Meyer ◽  
L. Mendoza-Zelis ◽  
F. H. Sanchez ◽  
...  
Keyword(s):  
Long Range ◽  
Milling Time ◽  
Continuous Heating ◽  
X Ray Diffraction ◽  
Mechanical Grinding ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Diffusion Controlled ◽  
Transmission Mössbauer Spectroscopy ◽  
Kinetics Of

ABSTRACTThe evolution of the B2-AlFe phase during mechanical grinding in Ar has been examined as a function of milling time by X-Ray diffraction, transmission Mössbauer spectroscopy and differential scanning calorimetry. Short and long range disorder was observed to increase with the mechanical treatment up to the attainment of a steady state. The evolution of the long range order parameter and of the local atomic configurations at Fe sites were analyzed in terms of possible mechanisms for milling induced disordering. The kinetics of the thermal reordering was studied under continuous heating and isothermal calorimetrie regimes. Modeling of the reordering processes by diffusion controlled growth of pre-existing ordered grains is presented as well as the estimated values of both the enthalpy and the activation energy of the reordering process. The results are consistent with a non uniform distribution of disorder throughout the sample and will be compared with preceding information on related systems.

scholarly journals Investigation of Crystalline and Tensile Properties of Carbon Nanotube-Filled Polyamide-12 Fibers Melt-Spun by Industry-Related Processes

2012 ◽  
Vol 7 (3) ◽  
pp. 155892501200700 ◽  
Author(s):  
Sanjukta Chatterjee ◽  
Felix A. Reifler ◽  
Bryan T. Chu ◽  
Rudolf Hufenus
Keyword(s):  
Mechanical Properties ◽  
Melt Spinning ◽  
Polymer Fibers ◽  
High Tensile Strength ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Polyamide 12 ◽  
Industrial Standards ◽  
Crystalline Domains

This paper addresses the influence of carbon nanotubes (CNT) on the structure and mechanical properties of high tensile strength thermoplastic polymer fibers. Polyamide (PA) fibers with different draw ratios, with and without CNTs as fillers, and having mechanical properties close to industrial standards were spun in a pilot melt spinning plant. The morphology of the fibers was investigated using optical microscopy, nuclear magnetic resonance (NMR) and 2-D wide angle x-ray diffraction (WAXD). Differential scanning calorimetry (DSC) was carried out to get an estimate of the crystallinity. For a concise interpretation of the results of the tensile measurements performed on the fibers, a parameter was developed to account for the detrimental influence of polymer extrusion on their mechanical properties. The CNTs seemed to act as sites for the growth of un-oriented crystalline domains converted from oriented regions, without yielding a mechanical reinforcing effect.

A Model for Formation and Consumption of Transient Phase

2011 ◽  
Vol 172-174 ◽  
pp. 646-651 ◽  
Author(s):  
Gamra Tellouche ◽  
Khalid Hoummada ◽  
Dominique Mangelinck ◽  
Ivan Blum
Keyword(s):  
Differential Scanning Calorimetry ◽  
Phase Formation ◽  
Transient Phase ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Proposed Model ◽  
Transient Phases ◽  
Kinetics Of

The phase formation sequence of Ni silicide for different thicknesses is studied by in situ X ray diffraction and differential scanning calorimetry measurements. The formation of a transient phase is observed during the formation of δ-Ni2Si; transient phases grow and disappear during the growth of another phase. A possible mechanism is proposed for the transient phase formation and consumption. It is applied to the growth and consumption of θ-Ni2Si. A good accordance is found between the proposed model and in situ measurement of the kinetics of phase formation obtained by x-ray diffraction and differential scanning calorimetry for higher thickness.

Characterization of Nanocrystalline γ–Fe2O3Prepared by Wet Chemical Method

1999 ◽  
Vol 14 (4) ◽  
pp. 1570-1575 ◽  
Author(s):  
G. Ennas ◽  
G. Marongiu ◽  
A. Musinu ◽  
A. Falqui ◽  
P. Ballirano ◽  
...  
Keyword(s):  
Isothermal Treatment ◽  
X Ray Diffraction ◽  
Ferrous Chloride ◽  
Scanning Calorimetry ◽  
Direct Transformation ◽  
X Ray ◽  
Transmission Electron ◽  
Xrd Techniques ◽  
Kinetics Of

Homogeneous maghemite (γ–Fe2O3) nanoparticles with an average crystal size around 5 nm were synthesized by successive hydrolysis, oxidation, and dehydration of tetrapyridino-ferrous chloride. Morphological, thermal, and structural properties were investigated by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and x-ray diffraction (XRD) techniques. Rietveld refinement indicated a cubic cell. The superstructure reflections, related to the ordering of cation lattice vacancies, were not detected in the diffraction pattern. Kinetics of the solid-state phase transition of nanocrystalline maghemite to hematite (α–Fe2O3), investigated by energy dispersive x-ray diffraction (EDXRD), indicates that direct transformation from nanocrystalline maghemite to microcrystalline hematite takes place during isothermal treatment at 385 °C. This temperature is lower than that observed both for microcrystalline maghemite and for nanocrystalline maghemite supported on silica.

Reaction Process of Al-TiO2-C-Ti-Fe Multiphase System during Combustion Synthesis

2007 ◽  
Vol 336-338 ◽  
pp. 2340-2343 ◽  
Author(s):  
Song He Meng ◽  
Xing Hong Zhang ◽  
Wei Feng Zhang
Keyword(s):  
Intermetallic Compounds ◽  
Xrd Analysis ◽  
Reaction Process ◽  
Multiphase System ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Reaction Characteristics ◽  
Lower Temperature ◽  
Kinetics Of

The reaction process and kinetics of Al-TiO2-C-Ti-Fe system were investigated by differential scanning calorimetry (DSC) analysis, X-ray diffraction (XRD) analysis and scanning electron microscope (SEM). In order to obtain the information of reaction process for complicated system, the reaction characteristics of Al-TiO2, Al-TiO2-C and Al-TiO2-C-Ti systems are explored firstly. The results show that the reaction process varies with temperature in Al-TiO2-C-Ti-Fe system. At the lower temperature, the dominating reaction in Al-TiO2-C-Ti-Fe system is that between Al and Ti, Al and Fe, and so TiAlx, FeAlx, and Ti2Fe intermetallic compounds form. With the temperature increasing, the intermetallic compounds are decomposed. Then the decomposed Ti and Al react with C and TiO2 respectively and the stable TiC, Al2O3 and Fe three phases form in the final product.

X-ray diffraction diagnostic paired with gas gun driven compression of polyethylene

2019 ◽  
Author(s):  
Rachel C. Huber ◽  
Erik B. Watkins ◽  
Dana M. Dattelbaum ◽  
Richard L. Gustavsen
Keyword(s):  
Dynamic Compression ◽  
Polymer Chains ◽  
Extreme Condition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gas Gun ◽  
Gas Guns ◽  
Crystalline Domains ◽  
Kinetics Of

Abstract Understanding the kinetics of phase transitions, including decomposition from reactants to products under extreme condition events is challenging. Capturing these processes require: 1) diagnostics that probe on the timescales and at energies capable of interacting with the dynamically evolving products, penetrating the opaqueness of the changing system; and 2) detectors sensitive enough to observe these events. Synchrotrons and free electron lasers provide ke-V-energy x-ray beams capable of penetrating the optical-opaqueness of the temporally evolving products. At the Dynamic Compression Sector at the Advanced Photon Source, the x-ray beam is coupled to single and two-stage gas guns capable of producing planar shocks at a range of projectile velocities while capturing in situ x-ray diffraction/scattering of the evolving material under dynamic compression. In this work, we demonstrate the utility of this approach in measuring the evolution of crystalline domains in shocked high-density polyethylene to P = 7.45 GPa, and have observed the compression and orientation of the polymer chains in real time.

scholarly journals Effects of Ball Milling and TiF3 Addition on the Dehydrogenation Temperature of Ca(BH4)2 Polymorphs

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4828
Author(s):  
Isabel Llamas Jansa ◽  
Oliver Friedrichs ◽  
Maximilian Fichtner ◽  
Elisa Gil Bardají ◽  
Andreas Züttel ◽  
...  
Keyword(s):  
Ball Milling ◽  
Hydrogen Desorption ◽  
Reaction Pathways ◽  
Desorption Peak ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Before And After ◽  
Kinetics Of ◽  
Desorption Reaction

The changes introduced by both ball milling and the addition of small amounts of TiF3 in the kinetics of the hydrogen desorption of three different Ca(BH4)2 polymorphs (α, β and γ) have been systematically investigated. The samples with different polymorphic contents, before and after the addition of TiF3, were characterized by powder X-ray diffraction and vibrational spectroscopy. The hydrogen desorption reaction pathways were monitored by differential scanning calorimetry. The hydrogen desorption of Ca(BH4)2 depends strongly on the amount of coexistent α, β and γ polymorphs as well as additional ball milling and added TiF3 to the sample. The addition of TiF3 increased the hydrogen desorption rate without significant dissociation of the fluoride. The combination of an α-Ca(BH4)2 rich sample with 10 mol% of TiF3 and 8 h of milling led to up to 27 °C decrease of the hydrogen desorption peak temperature.

Sign in / Sign up

Export Citation Format

Share Document