Strain Rate Dependent Mechanical Stability of Retained Austenite in Hot-Rolled Medium-Mn Sheet Steels

2021 ◽  
Vol 1016 ◽  
pp. 946-951
Author(s):  
Mateusz Morawiec ◽  
Adam Grajcar
Keyword(s):  
Strain Rate ◽  
Mechanical Stability ◽  
Total Elongation ◽  
Manganese Steel ◽  
Strain Rates ◽  
Sheet Steels ◽  
Rate Dependent ◽  
Medium Manganese Steel ◽  
Dynamic Tensile Test ◽  
Hot Rolled

The paper presents microstructural and mechanical results of medium manganese steel deformed under high strain rates. The rotary hammer tests at strain rates of 250, 500 and 1000 s-1 were applied. Mechanical properties under dynamic tensile loads were determined. According to the obtained results, when strain rate increased the yield point of the steel increased. An opposite trend was present regarding total elongation. In case of tensile strength, its level is similar for all analyzed deformation rates. The microstructure of the steel after the dynamic tensile test is composed of bainite, martensite and martensitic-austenitic islands. The strain-induced martensitic transformation was identified in microscopic investigations.

scholarly journals Strain-Rate-Dependent Deformation Behavior and Mechanical Properties of a Multi-Phase Medium-Manganese Steel

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 344 ◽  
Author(s):  
Simon Sevsek ◽  
Christian Haase ◽  
Wolfgang Bleck
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
Rate Sensitivity ◽  
Manganese Steel ◽  
Strain Rates ◽  
Rate Dependent ◽  
Medium Manganese Steel ◽  
Multi Phase

The strain-rate-dependent deformation behavior of an intercritically annealed X6MnAl12-3 medium-manganese steel was analyzed with respect to the mechanical properties, activation of deformation-induced martensitic phase transformation, and strain localization behavior. Intercritical annealing at 675 °C for 2 h led to an ultrafine-grained multi-phase microstructure with 45% of mostly equiaxed, recrystallized austenite and 55% ferrite or recovered, lamellar martensite. In-situ digital image correlation methods during tensile tests revealed strain localization behavior during the discontinuous elastic-plastic transition, which was due to the localization of strain in the softer austenite in the early stages of plastic deformation. The dependence of the macroscopic mechanical properties on the strain rate is due to the strain-rate sensitivity of the microscopic deformation behavior. On the one hand, the deformation-induced phase transformation of austenite to martensite showed a clear strain-rate dependency and was partially suppressed at very low and very high strain rates. On the other hand, the strain-rate-dependent relative strength of ferrite and martensite compared to austenite influenced the strain partitioning during plastic deformation, and subsequently, the work-hardening rate. As a result, the tested X6MnAl12-3 medium-manganese steel showed a negative strain-rate sensitivity at very low to medium strain rates and a positive strain-rate sensitivity at medium to high strain rates.

Microstructure Evolution and Mechanical Properties of 67GPa•% Grade Medium Manganese Steel

2021 ◽  
Vol 1035 ◽  
pp. 404-409
Author(s):  
Zhe Rui Zhang ◽  
Ren Bo Song ◽  
Nai Peng Zhou ◽  
Wei Feng Huo
Keyword(s):  
Mechanical Properties ◽  
Microstructure Evolution ◽  
Annealing Temperature ◽  
High Strength ◽  
Total Elongation ◽  
Manganese Steel ◽  
Experimental Steel ◽  
Medium Manganese Steel ◽  
Hot Rolled ◽  
Hot Rolled Steel

In this study, a new Fe-6Mn-4Al-0.4C high strength medium manganese hot rolled steel sheet was designed. The influence mechanism of the intercritical annealing (IA) temperature on microstructure evolution and mechanical properties of experimental steel were studied by SEM and XRD. The experimental steel was held for 30 minutes at 640°C, 680°C, 720°C, 760°C, 800°C, respectively. When the annealing temperature was 640°C, cementite particles precipitated between the austenite and ferrite phase boundary. As the annealing temperature increased, the cementite gradually dissolved and disappeared, the fraction of lamellar austenite increased significantly. When the annealing temperature is 800°C, the coarse equiaxed austenite and ferrite appeared. The yield strength (YS) decreased, the product of strength and elongation (PSE) and total elongation (TE) both increased first and then decreased, while the ultimate tensile strength (UTS) showed the opposite trend. The experimental steel exhibited excellent comprehensive mechanical properties after held at 760°C for 30 min. The UTS was 870 MPa, the YS was 703 MPa, and the TE was 77 %, the PSE was 67 GPa·%.

Strain Rate Effects on Mechanical Stability of Retained Austenite in TRIP Sheet Steels

2006 ◽  
Author(s):  
Ildong Choi ◽  
Dongmin Son ◽  
Sung-joon Kim ◽  
David K. Matlock ◽  
John G. Speer
Keyword(s):  
Strain Rate ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
Strain Rate Effects ◽  
Sheet Steels ◽  
Rate Effects

scholarly journals Extension of Flow Behaviour and Damage Models for Cast Iron Alloys with Strain Rate Effect

2020 ◽  
Author(s):  
Chuang Liu ◽  
Dongzhi Sun ◽  
Xianfeng Zhang ◽  
Florence Andrieux ◽  
Tobias Gerster
Keyword(s):  
Cast Iron ◽  
Constitutive Model ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Damage Model ◽  
Iron Alloys ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Damage Models ◽  
Rate Dependent

Abstract Cast iron alloys with low production cost and quite good mechanical properties are widely used in the automotive industry. To study the mechanical behavior of a typical ductile cast iron (GJS-450) with nodular graphite, uni-axial quasi-static and dynamic tensile tests at strain rates of 10− 4, 1, 10, 100, and 250 s− 1 were carried out. In order to investigate the effects of stress state, specimens with various geometries were used in the experiments. Stress–strain curves and fracture strains of the GJS-450 alloy in the strain-rate range of 10− 4 to 250 s− 1 were obtained. A strain rate-dependent plastic flow law based on the Voce model is proposed to describe the mechanical behavior in the corresponding strain-rate range. The deformation behavior at various strain rates is observed and analyzed through simulations with the proposed strain rate-dependent constitutive model. The available damage model from Bai and Wierzbicki is extended to take the strain rate into account and calibrated based on the analysis of local fracture strains. The validity of the proposed constitutive model including the damage model was verified by the corresponding experimental results. The results show that the strain rate has obviously nonlinear effects on the yield stress and fracture strain of GJS-450 alloys. The predictions with the proposed constitutive model and damage models at various strain rates agree well with the experimental results, which illustrates that the rate-dependent flow rule and damage models can be used to describe the mechanical behavior of cast iron alloys at elevated strain rates.

scholarly journals Development of a Cr-Ni-V-N Medium Manganese Steel with Balanced Mechanical and Corrosion Properties

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 705 ◽  
Author(s):  
Tarek Allam ◽  
Xiaofei Guo ◽  
Simon Sevsek ◽  
Marta Lipińska-Chwałek ◽  
Atef Hamada ◽  
...  
Keyword(s):  
Grain Size ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Twip Steel ◽  
Total Elongation ◽  
Manganese Steel ◽  
Ultrafine Grain ◽  
Corrosion Properties ◽  
Hot Rolled ◽  
20 Nm

A novel medium manganese (MMn) steel with additions of Cr (18%), Ni (5%), V (1%), and N (0.3%) was developed in order to provide an enhanced corrosion resistance along with a superior strength–ductility balance. The laboratory melted ingots were hot rolled, cold rolled, and finally annealed at 1000 °C for 3 min. The recrystallized single-phase austenitic microstructure consisted of ultrafine grains (~1.3 µm) with a substantial amount of Cr- and V-based precipitates in a bimodal particle size distribution (100–400 nm and <20 nm). The properties of the newly developed austenitic MMn steel X20CrNiMnVN18-5-10 were compared with the standard austenitic stainless steel X5CrNi18-8 and with the austenitic twinning-induced plasticity (TWIP) steel X60MnAl17-1. With a total elongation of 45%, the MMn steel showed an increase in yield strength by 300 MPa and in tensile strength by 150 MPa in comparison to both benchmark steels. No deformation twins were observed even after fracture for the MMn steel, which emphasizes the role of the grain size and precipitation-induced change in the austenite stability in controlling the deformation mechanism. The potentio-dynamic polarization measurements in 5% NaCl revealed a very low current density value of 7.2 × 10−4 mA/cm2 compared to that of TWIP steel X60MnAl17-1 of 8.2 × 10−3 mA/cm2, but it was relatively higher than that of stainless steel X5CrNi18-8 of 2.0 × 10−4 mA/cm2. This work demonstrates that the enhanced mechanical properties of the developed MMn steel are tailored by maintaining an ultrafine grain microstructure with a significant amount of nanoprecipitates, while the high corrosion resistance in 5% NaCl solution is attributed to the high Cr and N contents as well as to the ultrafine grain size.

Investigation of the axial compressive behavior of Kevlar fibers using the dynamic loop test

2019 ◽  
Vol 89 (18) ◽  
pp. 3825-3838
Author(s):  
Ahmad Abuobaid ◽  
Raja Ganesh ◽  
John W Gillespie
Keyword(s):  
Strain Rate ◽  
High Speed ◽  
Failure Strain ◽  
Kink Band ◽  
Test Method ◽  
Strain Rates ◽  
Compressive Failure ◽  
Band Formation ◽  
Rate Dependent ◽  
Strain And Strain Rate

A dynamic loop test method for measuring strain rate-dependent fiber properties was developed. During dynamic loop testing, the fiber ends are accelerated at constant levels of 20.8, 50 and 343 m/s2. The test method is used to study Kevlar® KM2-600, which fails in axial compression due to kink band formation. The compressive failure strain and strain rate at the onset of kink band formation is calculated from the critical loop diameter ( D C), which is monitored throughout the test using a high-speed camera. The results showed that compressive failure strain increases with strain rates from quasi-static to a maximum strain rate of 116 s−1 by a factor of ∼3. Kink angles (φ) and kink band spacing ( D S) were 60 ° ± 2 ° and 16 ± 3 μm, respectively, over the strain rates tested. Rate-dependent mechanisms of compressive failure by kink band formation were discussed.

scholarly journals Effect of Deformation Temperature on the Portevin-Le Chatelier Effect in Medium-Mn Steel

Metals ◽  
2018 ◽  
Vol 9 (1) ◽  
pp. 2 ◽  
Author(s):  
Barbara Grzegorczyk ◽  
Aleksandra Kozłowska ◽  
Mateusz Morawiec ◽  
Rafał Muszyński ◽  
Adam Grajcar
Keyword(s):  
Deformation Temperature ◽  
Tensile Deformation ◽  
Plastic Instability ◽  
Manganese Steel ◽  
Experimental Investigations ◽  
Medium Manganese Steel ◽  
Medium Mn Steel ◽  
Lower Strain ◽  
Chatelier Effect ◽  
Hot Rolled

Experimental investigations of the plastic instability phenomenon in a hot-rolled medium manganese steel were performed. The effects of tensile deformation in a temperature range of 20–140°C on the microstructure, mechanical properties, and flow stress serrations were analyzed. The Portevin–Le Chatelier (PLC) phenomenon was observed for the specimens deformed at 60 °C, 100 °C, and 140 °C. It was found that the deformation temperature substantially affects the type and intensity of serrations. The type of serration was changed at different deformation temperatures. The phenomenon was not observed at room temperature. The plastic instability occurring for the steel deformed at 60 °C was detected for lower strain levels than for the specimens deformed at 100 °C and 140 °C. The increase of the deformation temperature to 100 °C and 140 °C results in shifting the PLC effect to a post uniform deformation range. The complex issues related to the interaction of work hardening, the transformation induced plasticity (TRIP) effect, and the PLC effect stimulated by the deformation temperature were addressed.

Constitutive Modeling of a Thermoplastic Olefin Over a Broad Range of Strain Rates

2006 ◽  
Vol 128 (4) ◽  
pp. 551-558 ◽  
Author(s):  
Yan Wang ◽  
Ellen M. Arruda
Keyword(s):  
Strain Rate ◽  
Strain Hardening ◽  
Three Dimensional ◽  
Elastic Response ◽  
Strain Rates ◽  
Strain Behavior ◽  
Rate Dependent ◽  
State Dependent ◽  
Deformation State ◽  
Ann Arbor

A microstructually motivated, three-dimensional, large deformation, strain rate dependent constitutive model has been developed for a semi-crystalline, blended, thermoplastic olefin (TPO) (Wang, Y., 2002, Ph.D. thesis, The University of Michigan, Ann Arbor, MI). Various experiments have been conducted to characterize the TPO and to verify the modeling approach (Wang, Y., 2002, Ph.D. thesis, The University of Michigan, Ann Arbor, MI). The model includes a quantitative rate-dependent Young’s modulus, a nonlinear viscoelastic response between initial linear elastic response and yield due to inherent microstructural irregularity, rate and temperature dependent yield with two distinctive yield mechanisms for low and high strain rates, temperature-dependent strain hardening, plastic deformation of crystalline regions, and adiabatic heating. It has been shown to accurately capture the observed TPO stress-strain behavior including the rate-dependent initial linear elastic response; temperature, strain rate, and deformation state-dependent yield; temperature and deformation state-dependent strain hardening; and pronounced thermal softening effects at high (impact) strain rates. The model has also been examined for its ability to predict the response in plane strain compression based on material parameters chosen to capture the uniaxial compression response. The model is predictive of the initial strain rate dependent stiffness, yield, and strain hardening responses in plane strain. Such predictive capability demonstrates the versatility with which this model captures the three-dimensional anisotropic nature of TPO stress-strain behavior.

scholarly journals Inelastic Behavior in Repeated Shearing of Bovine White Matter

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Taylor S. Cohen ◽  
Andrew W. Smith ◽  
Panagiotis G. Massouros ◽  
Philip V. Bayly ◽  
Amy Q. Shen ◽  
...  
Keyword(s):  
White Matter ◽  
Strain Rate ◽  
Critical Strain ◽  
Mechanical Response ◽  
Tissue Mechanics ◽  
Strain Rates ◽  
Inelastic Behavior ◽  
Fiber Breakage ◽  
Rate Dependent ◽  
Strain Threshold

Understanding the brain’s response to multiple loadings requires knowledge of how straining changes the mechanical response of brain tissue. We studied the inelastic behavior of bovine white matter and found that when this tissue is stretched beyond a critical strain threshold, its reloading stiffness drops. An upper bound for this strain threshold was characterized, and was found to be strain rate dependent at low strain rates and strain rate independent at higher strain rates. Results suggest that permanent changes to tissue mechanics can occur at strains below those believed to cause physiological disruption or rupture of axons. Such behavior is characteristic of disentanglement in fibrous-networked solids, in which strain-induced mechanical changes may result from fiber realignment rather than fiber breakage.

Practical Design of Ni3Al with High Hot Workability

1996 ◽  
Vol 460 ◽  
Author(s):  
Yinmin Wang ◽  
Dongliang Lin ◽  
Yun Zhang
Keyword(s):  
Strain Rate ◽  
Compressive Strain ◽  
Tensile Tests ◽  
Rolling Process ◽  
Strain Rates ◽  
Hot Workability ◽  
Transmission Electron ◽  
Cr Addition ◽  
Hot Rolled ◽  
Compressive Tests

ABSTRACTFrom our previous work, Ni3Al polycrystals with combined addition of magnesium and silicon kept high values of compressive strain at rupture (CSR) when the strain rate rose. In order to further improve hot workability of Ni3Al, 7.9wt.% Cr was added. The compressive tests showed that 30%∼40% CSR values of the alloy had been kept in a wide temperature range of 1173K-1373K at strain rates of 10-2sec-1 and 10-2sec-1 in contrast with 15%∼25% CSR values of the alloy without Cr addition.In practical hot rolling process, at initial deformation temperature of 1373K, strain rate of 1.0 sec-1 and by controlling reduction within 10∼15% each rolling pass, Ni3Al ingots were successfully hot-rolled into polycrystals with different deformations, the maximum of which was 55%. The deformed alloys had manifestly enhanced mechanical properties shown by tensile tests.The dislocation configurations of deformed alloys have been investigated by using transmission electron microscope(TEM).

Sign in / Sign up

Export Citation Format

Share Document