Steam Oxidation of TP 347H FG in Power Plants

2006 ◽  
Vol 522-523 ◽  
pp. 181-188 ◽  
Author(s):  
A.N. Hansson ◽  
Melanie Montgomery
Keyword(s):  
Oxide Layer ◽  
Kinetic Data ◽  
Power Plants ◽  
Oxidation Behaviour ◽  
Oxidation Time ◽  
Steam Oxidation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Supercritical Steam Conditions

The long term oxidation behaviour of TP 347H FG at ultra supercritical steam conditions was assessed by exposing the steel in test superheater loops in a Danish coal-fired power plant. The steamside oxide layer was investigated with scanning electron microscopy and energy dispersive X-ray diffraction in order to reveal the effect of oxidation time and temperature on the microstructure. A double layered oxide formed during steam oxidation. The morphology of the inner Cr-containing layer was influenced by the oxidation temperature. At temperatures below approx. 585oC, it consisted of regions of Fe-Ni-Cr spinel surrounded by Fe-Cr oxide. At higher temperatures almost the entire inner oxide layer was composed of Fe-Cr oxide. Possible mechanisms for the oxide growth are discussed and it is suggested that faster Cr transport within the alloy at higher temperatures explains the change in morphology. This hypothesis is supported by thermodynamic calculations and kinetic data. The thickness of the inner oxide layer did not change significantly with oxidation time and temperature for exposures less than 30000 h; however after 57554 h the thickness had increased significantly at the lowest temperatures.

scholarly journals Changes of crystallite sizes in the oxide layer forming during long-term operation of 10CrMo9-10 steel

2017 ◽  
Vol 3 (20) ◽  
pp. 289-296
Author(s):  
Monika Gwoździk
Keyword(s):  
Oxide Layer ◽  
Tube Wall ◽  
X Ray Diffraction ◽  
Oxide Layers ◽  
X Ray ◽  
Term Operation ◽  
Long Time ◽  
Crystallite Sizes ◽  
Scherrer Formula

The paper contains results of the studies on X-ray diffraction analysis XRD (studying the phase composition, crystallite sizes) of oxide layers on 10CrMo9-10 steel, operated for a long time at an elevated temperature (T = 525°C, t = 200,000 h). The oxide layer was studied on a surface and a cross-section at the outer on the inlet both on the fire and counter-fire side of the tube wall surface. X-ray studies were carried out on the outer surface of a tube, and then the layer surface was polished down and the diffraction measurements were performed again to determine crystallite size in oxide layers. Based on the width and the position of the main coat and substrate reflections, the size of the crystallites was determined using the Scherrer formula.

Analysis of crystallite size changes in a hematite and magnetite formed on steel used in the power idustry

2017 ◽  
Vol 1 (21) ◽  
pp. 65-73
Author(s):  
Monika Gwoździk
Keyword(s):  
Elevated Temperature ◽  
Oxide Layer ◽  
Cross Section ◽  
X Ray ◽  
Term Operation ◽  
Diffraction Line Profile ◽  
Crystallite Sizes ◽  
Scherrer Formula ◽  
Pipe Outlet

The paper presents results of studies on the crystallite sizes of oxide layer formed during a long-term operation on 10CrMo9-10 steel at an elevated temperature (T = 545° C, t = 200,000 h). This value was determined by a method based on analysis of the diffraction line profile, according to a Scherrer formula. The oxide layer was studied on a surface and a cross-section at the outer and inner site on the pipe outlet, at the fire and counter-fire wall of the tube. X-ray studies were carried out on the surface of a tube, then the layer’s surface was polished and the diffraction measurements repeated to reveal differences in the originated oxides layer.

scholarly journals Enhancing carbonation and chloride resistance of autoclaved concrete by incorporating nano-CaCO3

2020 ◽  
Vol 9 (1) ◽  
pp. 998-1008
Author(s):  
Guo Li ◽  
Zheng Zhuang ◽  
Yajun Lv ◽  
Kejin Wang ◽  
David Hui
Keyword(s):  
Cement Hydration ◽  
Mercury Intrusion Porosimetry ◽  
Hardened Concrete ◽  
Optimal Dosage ◽  
Hydration Products ◽  
X Ray Diffraction ◽  
Carbonation Depth ◽  
X Ray ◽  
Chloride Resistance

AbstractThree nano-CaCO3 (NC) replacement levels of 1, 2, and 3% (by weight of cement) were utilized in autoclaved concrete. The accelerated carbonation depth and Coulomb electric fluxes of the hardened concrete were tested periodically at the ages of 28, 90, 180, and 300 days. In addition, X-ray diffraction, thermogravimetry, and mercury intrusion porosimetry were also performed to study changes in the hydration products of cement and microscopic pore structure of concrete under autoclave curing. Results indicated that a suitable level of NC replacement exerts filling and accelerating effects, promotes the generation of cement hydration products, reduces porosity, and refines the micropores of autoclaved concrete. These effects substantially enhanced the carbonation and chloride resistance of the autoclaved concrete and endowed the material with resistances approaching or exceeding that of standard cured concrete. Among the three NC replacement ratios, the 3% NC replacement was the optimal dosage for improving the long-term carbonation and chloride resistance of concrete.

Evaluation of Si Coating on Ferritic Steels by CVD-FBR Technology in Steam Oxidation

2009 ◽  
Vol 289-292 ◽  
pp. 413-420 ◽  
Author(s):  
F.J. Bolívar ◽  
L. Sánchez ◽  
M.P. Hierro ◽  
F.J. Pérez
Keyword(s):  
Power Plants ◽  
Protective Coatings ◽  
Steam Oxidation ◽  
Steam Turbines ◽  
X Ray Diffraction ◽  
Steam Power ◽  
Factors Affecting ◽  
Steam Power Plants ◽  
Temperature And Pressure ◽  
Major Factors

The development of new power generation plants firing fossil fuel is aiming at achieving higher thermal efficiencies of the energy conversion process. The major factors affecting the efficiency of the conventional steam power plants are the temperature and, to a lesser extent, the pressure of the steam entering the turbine. The increased operating temperature and pressure require new materials that have major oxidation resistance. Due to this problem, in the last years numerous studies have been conducted in order to develop new coatings to enhance the resistance of steels with chromium contents between 9 and 12% wt against steam oxidation in order to allow operation of steam turbines at 650 0C. In this study, Si protective coatings were deposited by CVD-FBR on ferritic steel P-91. These type of coatings have shown to be protective at 650 0C under steam for at least 3000 hours of laboratory steam exposure under atmospheric pressure. Morphology and composition of coatings were characterized by different techniques, such as scanning electron microscopy (SEM), electron probe microanalysis, and X-ray diffraction (XRD). The results show a substantial increase of steam oxidation protection afforded by Si coating by CVD-FBR process.

Long-term Room Temperature Instability in Thermal Conductivity of InGaZnO Thin Films

MRS Advances ◽  
2016 ◽  
Vol 1 (22) ◽  
pp. 1631-1636 ◽  
Author(s):  
Boya Cui ◽  
D. Bruce Buchholz ◽  
Li Zeng ◽  
Michael Bedzyk ◽  
Robert P. H. Chang ◽  
...  
Keyword(s):  
Thin Films ◽  
Thermal Conductivity ◽  
Room Temperature ◽  
Storage Time ◽  
Laser Deposition ◽  
Low Oxygen ◽  
X Ray Diffraction ◽  
3Ω Method ◽  
X Ray

ABSTRACTThe cross-plane thermal conductivities of InGaZnO (IGZO) thin films in different morphologies were measured on three occasions within 19 months, using the 3ω method at room temperature 300 K. Amorphous (a-), semi-crystalline (semi-c-) and crystalline (c-) IGZO films were grown by pulsed laser deposition (PLD), followed by X-ray diffraction (XRD) for evaluation of film quality and crystallinity. Semi-c-IGZO shows the highest thermal conductivity, even higher than the most ordered crystal-like phase. After being stored in dry low-oxygen environment for months, a drastic decrease of semi-c-IGZO thermal conductivity was observed, while the thermal conductivity slightly reduced in c-IGZO and remained unchanged in a-IGZO. This change in thermal conductivity with storage time can be attributed to film structural relaxation and vacancy diffusion to grain boundaries.

scholarly journals Effects of Ultrasound on Zinc Oxide/Vermiculite/Chlorhexidine Nanocomposite Preparation and Their Antibacterial Activity

Nanomaterials ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 1309 ◽  
Author(s):  
Karla Čech Barabaszová ◽  
Sylva Holešová ◽  
Kateřina Šulcová ◽  
Marianna Hundáková ◽  
Barbora Thomasová
Keyword(s):  
Antimicrobial Activity ◽  
Particle Size ◽  
Zinc Oxide ◽  
Antibacterial Activity ◽  
Ultrasonic Treatment ◽  
Nanocomposite Materials ◽  
Hybrid Nanocomposite ◽  
X Ray Diffraction ◽  
X Ray

Microbial infection and biofilm formation are both problems associated with medical implants and devices. In recent years, hybrid organic-inorganic nanocomposites based on clay minerals have attracted significant attention due to their application potential in the field of antimicrobial materials. Organic drug/metal oxide hybrids exhibit improved antimicrobial activity, and intercalating the above materials into the interlayer of clay endows a long-term and controlled-release behavior. Since antimicrobial activity is strongly related to the structure of the material, ultrasonic treatment appears to be a suitable method for the synthesis of these materials as it can well control particle size distribution and morphology. This study aims to prepare novel, structurally stable, and highly antimicrobial nanocomposites based on zinc oxide/vermiculite/chlorhexidine. The influence of ultrasonic treatment at different time intervals and under different intercalation conditions (ultrasonic action in a breaker or in a Roset’s vessel) on the structure, morphology, and particle size of prepared hybrid nanocomposite materials was evaluated by the following methods: scanning electron microscopy, X-ray diffraction, energy dispersive X-ray fluorescence spectroscopy, carbon phase analysis, Fourier transforms infrared spectroscopy, specific surface area measurement, particle size analysis, and Zeta potential analysis. Particle size analyses confirmed that the ultrasonic method contributes to the reduction of particle size, and to their homogenization/arrangement. Further, X-ray diffraction analysis confirmed that ultrasound intercalation in a beaker helps to more efficiently intercalate chlorhexidine dihydrochloride (CH) into the vermiculite interlayer space, while a Roset’s vessel contributed to the attachment of the CH molecules to the vermiculite surface. The antibacterial activity of hybrid nanocomposite materials was investigated on Gram negative (Escherichia coli, Pseudomonas aeruginosa) and Gram positive (Staphylococcus aureus, Enterococcus faecalis) bacterial strains by finding the minimum inhibitory concentration. All hybrid nanocomposite materials prepared by ultrasound methods showed high antimicrobial activity after 30 min, with a long-lasting effect and without being affected by the concentration of the antibacterial components zinc oxide (ZnO) and CH. The benefits of the samples prepared by ultrasonic methods are the rapid onset of an antimicrobial effect and its long-term duration.

Synthesis of Trilaminar Core–Shell Au/α-Fe2O3@SnO2Nanocomposites and their Application for Nonenzymatic Dopamine Electrochemical Sensing

NANO ◽  
2019 ◽  
Vol 14 (11) ◽  
pp. 1950138 ◽  
Author(s):  
Sai Zhang ◽  
Shijun Yue ◽  
Jiajia Li ◽  
Jianbin Zheng ◽  
Guojie Gao
Keyword(s):  
Electron Microscopy ◽  
High Sensitivity ◽  
Electrochemical Sensing ◽  
Synthesis Process ◽  
Core Shell ◽  
X Ray Diffraction ◽  
X Ray ◽  
Long Term Stability ◽  
Transmission Electron

Au nanoparticles anchored on core–shell [Formula: see text]-Fe2O3@SnO2 nanospindles were successfully constructed through hydrothermal synthesis process and used for fabricating a novel nonenzymatic dopamine (DA) sensor. The structure and morphology of the Au/[Formula: see text]-Fe2O3@SnO2 trilaminar nanohybrid film were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The electrochemical properties of the sensor were investigated by cyclic voltammetry and amperometry. The experimental results suggest that the composites have excellent catalytic property toward DA with a wide linear range from 0.5[Formula: see text][Formula: see text]M to 0.47[Formula: see text]mM, a low detection limit of 0.17[Formula: see text][Formula: see text]M (S/[Formula: see text]) and high sensitivity of 397.1[Formula: see text][Formula: see text]A[Formula: see text]mM[Formula: see text][Formula: see text]cm[Formula: see text]. In addition, the sensor exhibits long-term stability, good reproducibility and anti-interference.

Assessment of Fatigue Life for High-Temperature Pipeline Welds Using X-Ray Diffraction Technique

2007 ◽  
Vol 353-358 ◽  
pp. 130-133
Author(s):  
Keun Bong Yoo ◽  
Jae Hoon Kim
Keyword(s):  
High Temperature ◽  
Fatigue Life ◽  
Fatigue Damage ◽  
Power Plants ◽  
Low Cycle Fatigue ◽  
Diffraction Method ◽  
Life Assessment ◽  
Fatigue Properties ◽  
X Ray Diffraction ◽  
X Ray

The objective of this study is to examine the feasibility of the X-ray diffraction method for the fatigue life assessment of high-temperature steel pipes used for main steam pipelines, re-heater pipelines and headers etc. in power plants. In this study, X-ray diffraction tests were performed on the specimens simulated for low cycle fatigue damage, in order to estimate fatigue properties at the various stages of fatigue life. As a result of X-ray diffraction tests, it was confirmed that the full width at the half maximum (FWHM) decreased with an increase in the fatigue life ratio, and that the FWHM and the residual stress due to fatigue damage were algebraically linearly related to the fatigue life ratio. From this relationship, a direct assessment of the remaining fatigue life was feasible.

Sign in / Sign up

Export Citation Format

Share Document