Nano-Electro-Structural Evolution of Ni-Si Ohmic Contacts to 3C-SiC

2009 ◽  
Vol 615-617 ◽  
pp. 569-572
Author(s):  
Jens Eriksson ◽  
Fabrizio Roccaforte ◽  
Filippo Giannazzo ◽  
Raffaella Lo Nigro ◽  
Giuseppe Moschetti ◽  
...  
Keyword(s):  
Ohmic Contacts ◽  
Annealing Temperature ◽  
Structural Evolution ◽  
Electrical Characterization ◽  
Nickel Silicide ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
Nanoscale Measurements

This paper reports on the macro- and nanoscale electro-structural evolution, as a function of annealing temperature, of nickel-silicide Ohmic contacts to 3C-SiC, grown on 6H-SiC substrates by a Vapor-Liquid-Solid (VLS) technique. The structural and electrical characterization of the contacts, carried out by combining different techniques, showed a correlation between the annealing temperature and the electrical characteristics in both the macro- and the nanoscale measurements. Increasing the annealing temperature between 600 and 950 °C caused a gradual increase of the uniformity of the nanoscale current-distribution, with an accompanying reduction of the specific contact resistance from 5 x 10-5 to 8.4 x 10-6 Ωcm2. After high temperature annealing (950 °C) the structural composition of the contacts stabilized, as only the Ni2Si phase was detected. A comparison with previous literature findings suggests a superior crystalline quality of the single domain VLS 3C-SiC layers.

Comparative Study of the Current Transport Mechanisms in Ni2Si Ohmic Contacts on n- and p-Type Implanted 4H-SiC

2014 ◽  
Vol 778-780 ◽  
pp. 665-668 ◽  
Author(s):  
Marilena Vivona ◽  
Giuseppe Greco ◽  
Salvatore di Franco ◽  
Filippo Giannazzo ◽  
Fabrizio Roccaforte ◽  
...  
Keyword(s):  
Temperature Dependence ◽  
Ohmic Contacts ◽  
Electrical Characterization ◽  
Nickel Silicide ◽  
Specific Contact Resistance ◽  
Current Transport ◽  
Specific Contact ◽  
Thermionic Field Emission ◽  
P Type

The knowledge of the temperature behavior of Ohmic contacts is an important issue to understand the device operation. This work reports an electrical characterization as a function of the temperature carried out on nickel silicide (Ni2Si) Ohmic contacts, used both for n-type and p-type implanted 4H-SiC layers. The temperature dependence of the specific contact resistance suggested that a thermionic field emission mechanism dominates the current transport for contacts on p-type material, whereas a current transport by tunneling is likely occurring in the contacts on n-type implanted SiC. Furthermore, from the temperature dependence of the electrical characteristics, the activation energies for Al and P dopants were determined, resulting of 145 meV and 35 meV, respectively. The thermal stability of the electrical parameters has been demonstrated upon a long-term (up to ~100 hours) cycling in the temperature range 200-400°C.

Improvement of the Specific Contact Resistance on P-Type 4H-SiC by Using a Highly P-Typed Doped 4H-SiC Layer Selectively Grown by VLS Transport

2014 ◽  
Vol 806 ◽  
pp. 57-60
Author(s):  
Nicolas Thierry-Jebali ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Mihai Lazar ◽  
Gabriel Ferro ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Schottky Barrier Height ◽  
Annealing Temperature ◽  
Process Condition ◽  
Specific Contact Resistance ◽  
High Doping Level ◽  
Annealing Temperatures ◽  
Specific Contact ◽  
P Type

This work reports on the improvement of ohmic contacts made on heavily p-type doped 4H-SiC epitaxial layer selectively grown by Vapor-Liquid-Solid (VLS) transport. Even before any annealing process, the contact is ohmic. This behavior can be explained by the high doping level of the VLS layer (Al concentration > 1020 cm-3) as characterized by SIMS profiling. Upon variation of annealing temperatures, a minimum value of the Specific Contact Resistance (SCR) down to 1.3x10-6 Ω.cm2 has been obtained for both 500 °C and 800 °C annealing temperature. However, a large variation of the SCR was observed for a same process condition. This variation is mainly attributed to a variation of the Schottky Barrier Height.

Current Transport Mechanisms in Au-Free Metallizations for CMOS Compatible GaN HEMT Technology

2020 ◽  
Vol 1004 ◽  
pp. 725-730
Author(s):  
Fabrizio Roccaforte ◽  
Monia Spera ◽  
Salvatore Di Franco ◽  
Raffaella Lo Nigro ◽  
Patrick Fiorenza ◽  
...  
Keyword(s):  
Barrier Height ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Current Transport ◽  
Large Area ◽  
Si Substrates ◽  
Ohmic Behavior ◽  
Specific Contact ◽  
Thermionic Field Emission

Gallium nitride (GaN) and its AlGaN/GaN heterostructures grown on large area Si substrates are promising systems to fabricate power devices inside the existing Si CMOS lines. For this purpose, however, Au-free metallizations are required to avoid cross contaminations. In this paper, the mechanisms of current transport in Au-free metallization on AlGaN/GaN heterostructures are studied, with a focus on non-recessed Ti/Al/Ti Ohmic contacts. In particular, an Ohmic behavior of Ti/Al/Ti stacks was observed after an annealing at moderate temperature (600°C). The values of the specific contact resistance ρc decreased from 1.6×104 Ω.cm2 to 7×105 Ω.cm2 with increasing the annealing time from 60 to 180s. The temperature dependence of ρc indicated that the current flow is ruled by a thermionic field emission (TFE) mechanism, with barrier height values of 0.58 eV and 0.52 eV, respectively. Finally, preliminary results on the forward and reverse bias characterization of Au-free tungsten carbide (WC) Schottky contacts are presented. This contact exhibited a barrier height value of 0.82 eV.

scholarly journals Ohmic contacts to Si-implanted and un-implanted n-type GaN

1995 ◽  
Vol 395 ◽  
Author(s):  
J. Brown ◽  
J Ramer ◽  
K. ZHeng ◽  
L.F. Lester ◽  
S.D. Hersee ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Annealing Temperature ◽  
Contact Resistivity ◽  
Contact Structures ◽  
Specific Contact Resistance ◽  
Resistance Variation ◽  
Specific Contact ◽  
Metal Layers ◽  
Nitrogen Vacancies

ABSTRACTWe report on ohmic contacts to Si-implanted and un-implanted n-type GaN on sapphire. A ring shaped contact design avoids the need to isolate the contact structures by additional implantation or etching. Metal layers of Al and Ti/Al were investigated. On un-implanted GaN, post metalization annealing was performed in an RTA for 30 seconds in N2 at temperatures of 700, 800, and 900°C, A minimum specific contact resistance (rc) of 1.4×10−5 Ω-cm2 was measured for Ti/Al at an annealing temperature of 800°C. Although these values are reasonably low, variations of 95% in specific contact resistance were measured within a 500 µm distance on the wafer. These results are most likely caused by the presence of compensating hydrogen. Specific contact resistance variation was reduced from 95% to 10% by annealing at 900°C prior to metalization. On Si-implanted GaN, un-annealed ohmic contacts were formed with Ti/Al metalization. The implant activation anneal of 1120°C generates nitrogen vacancies that leave the surface heavily n-type, which makes un-annealed ohmic contacts with low contact resistivity possible.

Low Resistance Ohmic Contacts Formation and Mechanism of Current Transport Through p-GaN and p-AlGaN

2008 ◽  
Vol 1108 ◽  
Author(s):  
Indra Chary ◽  
Boris Borisov ◽  
Vladimir Kuryatkov ◽  
Yuriy Kudryavtsev ◽  
R Asomoza ◽  
...  
Keyword(s):  
Ohmic Contact ◽  
Ohmic Contacts ◽  
Annealing Temperature ◽  
Hole Concentration ◽  
Specific Contact Resistance ◽  
Current Transport ◽  
Bilayer Thickness ◽  
Aluminum Oxides ◽  
Mg Doping ◽  
Specific Contact

AbstractWe report the influence of surface treatment, annealing temperature and metal bilayer thickness on the specific contact resistance (ρc) of Au/Ni ohmic contacts to p-GaN and p-AlGaN. Ohmic contact on p-GaN with a hole concentration of 6.5 x 1017 cm-3, shows the lowest ρc of ˜9.2 x 10-6 Ω cm2, when GaN was treated in HCl:H2O (3:1) solution before metal deposition and annealed at 500°C for 10 minutes in 90% N2 and 0% O2 atmosphere. Similar procedure applied on p-AlxGa1-xN (x = 5-7%), with a hole concentration of 2.3 x 1017 cm-3, yields a ρc of 1.8 x 10-4 Ω cm2. An increase is observed in ρc when Mg doping exceeds 4 x 1019 cm-3 in both p-GaN and p-AlGaN. This is attributed to Mg self compensation. This increase is more pronounced in AlGaN which we attribute to the presence of residual native aluminum oxides.

The Effects of Thermal Processing on Interfacial Microstructure for Thin Multilayered Metal Ohmic Contacts to p+-AlGaAs

1995 ◽  
Vol 382 ◽  
Author(s):  
M.W. Cole ◽  
W.Y. Han ◽  
K.A. Jones
Keyword(s):  
Ohmic Contacts ◽  
Annealing Temperature ◽  
Chemical Diffusion ◽  
Interfacial Microstructure ◽  
Specific Contact Resistance ◽  
Interfacial Region ◽  
Electrical Measurements ◽  
Two Phase ◽  
Specific Contact ◽  
P Type

ABSTRACTInterfacial microstructure and phase composition of PtTiGePd ohmic contacts to heavily C doped AlGaAs were investigated as a function of annealing temperature. Results of the material analyses were used to explain the specific contact resistances measured for each thermal treatment. Evidence of interdiffusion and compound formation between AIGaAs and Pd was visible in a Ga rich Pd-Ga-As reaction zone prior to heat treatment. This phase is critical for the formation of Ga vacancies, which upon heating are occupied by in-diffusing Ge. As the annealing temperature was elevated, from 530 - 600°C, As began to out-diffuse. This As out-diffusion, which is critical to the formation of good p-type ohmic contacts, contributed to the creation and development of the two phase TiAs/Pd12Ga2Ge5 interfacial region overlying the AlGaAs substrate. In response to the enhanced As out-diffusion at 600°C, the interfacial region became laterally continuous, compositionally uniform, and the specific contact resistance achieved its minimum value. Athigher annealing temperatures, ∼650°C, the electrical measurements degraded in response to intensive chemical diffusion and development of a broad, non-uniform multi-phased interfacial region.

Characterization of the Al/RuO2 Interface Upon Thermal Annealing

1990 ◽  
Vol 181 ◽  
Author(s):  
Quat T. Vu ◽  
E. Kolawa ◽  
M-A. Nicolet
Keyword(s):  
Contact Resistance ◽  
Annealing Temperature ◽  
Electrical Measurement ◽  
Specific Contact Resistance ◽  
Annealing Duration ◽  
Type Model ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Specific Contact

ABSTRACTWe have characterized the Al/RuO2 interface after annealing at temperatures in the range 450° C-550° C for durations up to several hours by backscattering spectrometry, cross-sectional transmission electron microscopy, and electrical four point probe measurement of specially designed structures. The electrical measurement yields the specific contact resistance of the interface by applying a transmission line type model developped for this purpose. An interfacial aluminum-oxygen polycrystalline compound is shown to grow with annealing temperature and duration, with a concurrent reduction of a thin layer of RuO2. However, the specific contact resistance between Al and RuO2 is found to decrease with annealing duration at 500°C. This last result indicates that the interfacial reaction does not lead to an insulating interface as could have been expected if the growth were pure and dense A12O3.

Fabrication and Characterization of Ohmic Contacts to 3C-SiC Layers Grown on Silicon

2019 ◽  
Vol 963 ◽  
pp. 485-489
Author(s):  
Monia Spera ◽  
Giuseppe Greco ◽  
Raffaella Lo Nigro ◽  
Salvatore di Franco ◽  
Domenico Corso ◽  
...  
Keyword(s):  
Structural Analysis ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
X Ray ◽  
Specific Contact ◽  
Fabrication And Characterization ◽  
P Type

This paper reports on the formation and characterization of Ohmic contacts to n-type and p-type type 3C-SiC layers grown on silicon substrates. In particular, Ohmic contact behavior was obtained either using Ni or Ti/Al/Ni layers annealed at 950°C. The values of the specific contact resistance ρc estimated by means of circular TLM (C-TLM) structures varied in the range ~ 10-3-10-5 Ωcm2, depending on the doping level of the 3C-SiC layer. A structural analysis performed by X-Ray Diffraction (XRD) allowed to identify the main phases formed upon annealing, i.e., Ni2Si and Al3Ni2. The morphology of the reacted contacts depended on that of the underlying substrate. The results can be useful for the development of a variety of devices on the cubic 3C-SiC polytype.

Low Resistance Ti-Si-C Ohmic Contacts for 4H-SiC Power Devices Using Laser Annealing

2017 ◽  
Vol 897 ◽  
pp. 399-402 ◽  
Author(s):  
Milantha de Silva ◽  
Teruhisa Kawasaki ◽  
Takamaro Kikkawa ◽  
Shinichiro Kuroki
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Laser Annealing ◽  
Electrical Contact ◽  
Nickel Silicide ◽  
Specific Contact Resistance ◽  
Low Resistance ◽  
Specific Contact ◽  
Face Side ◽  
Non Equilibrium

Non-equilibrium laser silicidations for low-resistance ohmic contact to 4H-SiC C-face with Titanium was demonstrated. Ti is one of carbon-interstitial type metals. In a conventional nickel silicide (NiSi) electrode on SiC, a carbon agglomeration at the silicide/SiC interface occurs, and contact resistance becomes larger. For suppressing the carbon agglomeration, in this research, nanoseconds non-equilibrium laser annealing was introduced, and also Ti was introduced to form both silicide and carbide. Ti (75, 100 nm)/SiC and Ni (75, 100 nm)/SiC contacts were formed on C-face side of 4H-SiC substrates. Electrical contact properties were investigated after 40 nanoseconds pulse laser annealing in Ar ambient and rapid thermal annealing. As the result, In the case of laser annealing, the lowest specific contact resistance of 2.4×10-4 Ωcm2 was obtained in Ti (75 nm)/SiC sample in the laser power of 2.5 J/cm2.

Formation and Characterization of Ohmic Contacts on Diamond

1992 ◽  
Vol 270 ◽  
Author(s):  
V. Venkatesan ◽  
D.M. Malta ◽  
K. Das
Keyword(s):  
Ion Implantation ◽  
Contact Resistance ◽  
Ohmic Contacts ◽  
Chemical Vapor ◽  
Polycrystalline Diamond ◽  
Temperature Cycling ◽  
Specific Contact Resistance ◽  
Naturally Occurring ◽  
Specific Contact

ABSTRACTLow resistance ohmic contacts have been fabricated on a naturally occurring lib diamond crystal and on polycrystalline diamond films by B ion-implantation and subsequent Ti/Au bilayer metallization. A high B concentration was obtained at the surface by ion implantation, a postimplant anneal and a subsequent chemical removal of the graphite layer. A bilayer metallization of Ti followed by Au, annealed at 850°C, yielded specific contact resistance values (as measured using a standard transmission line model (TLM) pattern) of the order of 10-5 Ω cm2 for chemical vapor deposition (CVD) grown polycrystalline films and the natural lib crystal. Specific contact resistance values have also been determined from circular TLM measurements on CVD films and the values compared to those from standard TLM measurements. These contacts were stable to a measurement temperature of ∼400°C and no degradation due to temperature cycling was observed.

Sign in / Sign up

Export Citation Format

Share Document