Experimental Study on Spray Cutting Ni-Based Superalloy

2012 ◽  
Vol 723 ◽  
pp. 317-321
Author(s):  
Yu Wang ◽  
Yuan Sheng Zhai ◽  
Fu Gang Yan ◽  
Xian Li Liu
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Parameters ◽  
Production Mode ◽  
Effective Reduction ◽  
Reasonable Choice ◽  
Base Superalloy

In this paper, the effect of cutting parameters on cutting force, cutting temperature and surface roughness on cutting force, cutting temperature and surface roughness are experimentally studied in spray cutting GH4169 Ni-base superalloy used carbide cutting tools. The results showed that reasonable choice of cutting parameters can effective reduction of cutting force and cutting temperature, and improve the machining surface roughness. Thus realizing clean production mode.

Cutting Behavior of Self-Lubricating Ceramic Tool in Dry Machining of 40Cr Quenched Steel

2021 ◽  
Vol 871 ◽  
pp. 176-188
Author(s):  
Ben Yuan Wang ◽  
Guang Chun Xiao ◽  
Zhao Qiang Chen ◽  
Ming Dong Yi ◽  
Jing Jie Zhang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Friction Coefficient ◽  
Cutting Force ◽  
Solid Lubricant ◽  
Cutting Temperature ◽  
Cutting Parameters ◽  
Ceramic Composites ◽  
Ceramic Tool ◽  
Cutting Depth ◽  
Ceramic Tools

In this paper, the dry cutting performance of Al2O3/TiC-based ceramic composites with nanoCaF2 was studied. Compared with the Al2O3/TiC ceramic tool, the Al2O3/TiC/CaF2 ceramic tool has lower cutting force, cutting temperature and surface roughness when milling 40Cr hardened steel. Three cutting parameters of cutting speed, feed per tooth, and cutting depth were used to conduct orthogonal experiments to study its changing trend. Through testing of cutting force, cutting temperature and surface roughness, and by comparison with ceramic tools without nanosolid lubricant added, the order of influence of three cutting parameters on cutting force, cutting temperature and surface roughness was obtained. The experimental results showed that the cutting force, cutting temperature and surface roughness of Al2O3/TiC/CaF2 ceramic tools containing nanoCaF2 werebetter than those of Al2O3/TiC ceramic tools. The cutting force, the cutting temperature, and the surface roughness were respectively reduced by 16.5%, 25.8% and 43% compared to when no solid lubricant was added. In addition, after adding solid lubricant, the effect of cutting depth on cutting force was significantly reduced. The average friction coefficient of the tool rake surface was 31.1% lower than that of ceramic tools without solid lubricant. In order to explain this phenomenon, through scanning electron microscopy (SEM) scanning and energy spectroscopy (EDS) elemental analysis, the wear reduction mechanism of solid lubricants was analyzed, that is, during the cutting process, nanosolid lubricants precipitated and formed lubricating film on the rake surface of the tool to reduce the friction coefficient. This was also the main reason for reducing the cutting temperature.

Force and Temperature in Dry Cutting of Hardened W18Cr4V with PCBN

2010 ◽  
Vol 431-432 ◽  
pp. 559-563
Author(s):  
Hai Rong Wu ◽  
Guo Qin Huang ◽  
Xi Peng Xu
Keyword(s):  
Experimental Study ◽  
Cutting Force ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Dry Cutting ◽  
Feeding Speed ◽  
Strain Gauge Dynamometer ◽  
Three Components

An experimental study was carried out to investigate the effects of cutting parameters on cutting force and temperature in cutting of hardened W18Cr4V with PCBN cutter. Three components of cutting force were recorded by a strain-gauge dynamometer and the cutting temperature was measured by a nature thermocouple of tool-workpiece. The cutting parameters were arranged by orthogonal method. It is shown that the cutting temperature increased with each of the three cutting parameters and the main effecting factor is feeding speed. The three components of cutting force increased greatly with an increase in feeding speed and cutting depth. But the forces decreased a little as cutting speed increased. The main and axial cutting forces depend mainly on cutting depth whereas the radius force is mainly influenced by feeding speed.

scholarly journals Machinability of Luxury Vinyl Tiles during Plain Milling Using a Helical Cutter

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2174 ◽  
Author(s):  
Zhaolong Zhu ◽  
Pingxiang Cao ◽  
Xiaolei Guo ◽  
Xiaodong (Alice) Wang ◽  
Fan Zhang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Helix Angle ◽  
Helical Milling ◽  
Tool Geometry ◽  
Cutting Depth ◽  
Diamond Cutting Tools

In order to better provide a theoretical basis for the machining of luxury vinyl tiles, a helical milling experiment was conducted by using diamond cutting tools, and special attention was given to the trends of cutting force and surface roughness in respect to tool geometry and cutting parameters. The results showed that the resultant force was negatively correlated to the helix angle and cutting speed, but positively correlated with the cutting depth. Then, that the surface roughness increased with a decrease of the helix angle and an increase of cutting depth, while as cutting speed raised, the surface roughness first declined and then increased. Thirdly, the cutting depth was shown to have the greatest influence on both cutting force and surface roughness, followed by helix angle and cutting speed. Fourth, the contribution of cutting depth only was significant to cutting force, while both the helix angle and cutting speed had insignificant influence on the cutting force and surface roughness. Finally, the optimal cutting conditions were proposed for industrial production, in which the helix angle, cutting speed and cutting depth were 70°, 2200 m/min and 0.5 mm, respectively.

scholarly journals Study on the Cutting Performance of Micro Textured Tools on Cutting Ti-6Al-4V Titanium Alloy

Micromachines ◽  
2020 ◽  
Vol 11 (2) ◽  
pp. 137 ◽  
Author(s):  
Kairui Zheng ◽  
Fazhan Yang ◽  
Na Zhang ◽  
Qingyu Liu ◽  
Fulin Jiang
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Cutting Force ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Performance ◽  
Cemented Carbide ◽  
Feed Force ◽  
Cemented Carbide Tools

Titanium alloys are widely used in various fields, but their machinability is poor because the chip would easily adhere to the tool surface during cutting, causing poor surface quality and tool wear. To improve the cutting performance of titanium alloy Ti-6Al-4V, experiments were conducted to investigate the effect of micro textured tool on the cutting performances. The cemented carbide tools whose rake faces were machined with line, rhombic, and sinusoidal groove textures with 10% area occupancy rates were adopted as the cutting tools. The effects of cutting depth and cutting speed on feed force and main cutting force were discussed based on experimental results. The results show that the cutting force produced by textured tools is less than that produced by non-textured tools. Under different cutting parameters, the best cutting performance can be obtained by using sinusoidal textured tools among the four types of tools. The wear of micro textured tools is significantly lower than that of non-textured tools, due to a continuous lubrication film between the chip and the rake face of the tool that can be produced because the micro texture can store and replenish lubricant. The surface roughness obtained using the textured tool is better than that using the non-textured tool. The surface roughness Ra can be reduced by 35.89% when using sinusoidal textured tools. This study is helpful for further improving the cutting performance of cemented carbide tools on titanium alloy and prolonging tool life.

Surface Roughness and Cutting Force of Inconel 718 Machined by Different Cutting Tools

2010 ◽  
Vol 135 ◽  
pp. 232-237
Author(s):  
G.S. Geng ◽  
Jiu Hua Xu ◽  
Y.C. Fu ◽  
B. Y
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Inconel 718 ◽  
Nuclear Power ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Operating Conditions ◽  
Single Factor ◽  
Orthogonal Experiments ◽  
High Integrity

Given the stringent operating conditions to which super alloys are subjected to in aerospace, nuclear power and gas turbine industries, their efficient machining and generation of machined surfaces with high integrity assumes a lot of importance. Therefore, this paper presents an experimental investigation on the surface roughness and cutting force of Inconel 718 machined with several different kinds of cutting tools. Both single-factor and orthogonal experiments were carried out with cemented carbide, cermet and CBN tools. The effects of cutting tools and cutting parameters on the surface roughness and cutting force are investigated and the optimal cutting conditions are recommended.

Optimization of cutting parameters in CNC turning operation using Taguchi design of experiments

2011 ◽  
Vol 2 (2) ◽  
pp. 79-87 ◽  
Author(s):  
I. Hanafi ◽  
A. Khamlichi ◽  
F. Mata Cabrera ◽  
E. Almansa ◽  
A. Jabbouri
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Design Method ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Mechanical And Thermal Properties ◽  
Taguchi Design Of Experiments ◽  
Optimization Of Cutting Parameters

Abstract Non-reinforced and reinforced Poly-Ether-Ether-Ketone (PEEK) plastics have excellent mechanical and thermal properties. Machining is an efficient process that can be used to manufacture specific mechanical parts made from PEEK composites. Researchers have focused on improving the performance of machining operations with the aim of minimizing costs and improving quality of manufactured products, in order to get the best surface roughness and the minimum cutting force. The parameters evaluated are the cutting speed, the depth of cut and the feed rate. In this paper, the effect of the mentioned parameters on surface roughness and cutting force, in dry turning of reinforced PEEK with 30% of carbon fibers (PEEK CF30) using TiN coated cutting tools, is analyzed through using robust design techniques such as Taguchi's design method, signal-to-noise (S/N) ratio and statistical analysis tools such as Pareto-ANOVA. The obtained results have shown that Taguchi method and Pareto ANOVA are suitable for optimizing the cutting parameters with the minimum possible number of experiments, and the optimized process parameters were determined for surface roughness and cutting force criteria.

Development of Surface Roughness Prediction for Steel in CNC Turning by Using Response Surface Method

2011 ◽  
Vol 335-336 ◽  
pp. 921-926
Author(s):  
Siriwan Chanphong ◽  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Response Surface ◽  
Cutting Temperature ◽  
Cutting Parameters ◽  
Plain Carbon Steel ◽  
Cutting Condition ◽  
Surface Roughness Prediction ◽  
Roughness Prediction ◽  
Coated Carbide

This research presents the development of the surface roughness prediction in the turning process of the plain carbon steel with the coated carbide tool by using the response surface analysis with the Box-Behnken design. The effects of cutting parameters on the cutting force and the cutting temperature are investigated. The cutting force and the cutting temperature are measured to help analyze the relation between the surface roughness and the cutting conditions. The models of cutting force ratio and the cutting temperature are also proposed based on the experimental data. The surface plots are constructed to determine the optimum cutting condition referring to the minimum surface roughness.

Integrated Monitoring of Surface Roughness and Chip Formation by Utilizing Cutting Force and Cutting Temperature

2012 ◽  
Vol 538-541 ◽  
pp. 1338-1350
Author(s):  
Somkiat Tangjitsitcharoen ◽  
Suthas Ratanakuakangwan
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Chip Formation ◽  
Cutting Temperature ◽  
Cutting Parameters ◽  
Cutting Conditions ◽  
Integrated Monitoring ◽  
Roughness Model ◽  
Spectrum Density ◽  
Roughness Prediction

This research presents the integration of the surface roughness and chip formation monitoring by using the cutting force and the cutting temperature during the in-process turning. The surface roughness prediction model is proposed by utilizing the response surface analysis with the Box-Behnken design. The effects of cutting parameters on the cutting force and the cutting temperature are investigated. The cutting force and the cutting temperature are measured to help analyze the relation between the surface roughness and the cutting conditions. The models of the cutting force ratio and the cutting temperature are also proposed based on the experimental data. The in-process monitoring of chip formation is developed to detect the continuous chip and the broken chip by utilizing the power spectrum density of dynamic cutting force and the variance of the dynamic cutting temperature.The broken chip formation is required for the reliable turning operation. The algorithm is proposed to obtain the broken chip by changing the cutting conditions during the cutting process based on the cutting force and the cutting temperature. It has been proved by series of cutting experiments that the proposed surface roughness model can be effectively used to predict the surface roughness, and the broken chip is well identified by the proposed method.

scholarly journals Reasearch of The Effect of Graphene Nanoparticles and Sulfurized Additives to MQL for Machining of Ti-6Al-4V

2021 ◽  
Author(s):  
Ben Wang ◽  
Quanwei Yang ◽  
Jiawei Deng ◽  
Ning Hou ◽  
Xuezhi Wang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Cutting Force ◽  
Rapeseed Oil ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Machine Material ◽  
Comprehensive Properties ◽  
Graphene Nanoparticles ◽  
Ep Additive

Abstract given its favourable comprehensive properties, titanium alloy has been extensively developed and used in numerous fields. However, its low thermal conductivity and strong chemical activity have led to its reputation as a difficult-to-machine material. Thus, graphene nanoparticles and sulfur-based extreme pressure (EP) additive were added to rapeseed oil to increase the lubrication and cooling properties of the machining region. In this study, three lubricants were used to machine titanium alloy: rapeseed oil+graphene+sulfur-based EP additive, rapeseed oil+sulfur-based EP additive, and rapeseed oil; and the subsequent wear of cutting tools, cutting temperature, surface roughness, and cutting force were compared. The most favourable results were found for the combination of rapeseed oil+graphene+sulfur-based EP additive, effectively decreasing the temperature of the cutting area and wear of cutting tools. In comparison with rapeseed oil, the flank wear value decreased by 56.4%. Similarly, the surface roughness and cutting force with the rapeseed oil+graphene+sulfur-based EP additive were lowest, showing a decrease of 36.1% and 27.0% respectively when compared with rapeseed oil.

Sign in / Sign up

Export Citation Format

Share Document