Friction-Stir Welding of Zr-Modified AA5083 Sheets in Different Conditions

2016 ◽  
Vol 877 ◽  
pp. 365-370
Author(s):  
Sergey Malopheyev ◽  
Sergey Mironov ◽  
Rustam Kaibyshev
Keyword(s):  
Friction Stir Welding ◽  
Post Weld Heat Treatment ◽  
Stir Zone ◽  
Friction Stir ◽  
Ultrafine Grained ◽  
Aa5083 Aluminum Alloy ◽  
Cold Rolled ◽  
Material Conditions ◽  
Hot Rolled ◽  
Zone Microstructure

The effect of friction-stir welding (FSW) on microstructure and mechanical properties of Zr-modified AA5083 aluminum alloy was studied. FSW was observed to lead to the formation of fully recrystallized ultrafine-grained microstructures and preservation of nanoscale dispersoids in stir zone. The joint efficiency of the friction-stir welds for ultimate tensile strength was found to be 94% and 74% in the hot-rolled and cold-rolled preprocessed material conditions. The stir zone microstructure was predicted to be stable against abnormal grain growth during post-weld heat treatment.

Effect of Strain Hardening on the Joint Efficiency of an Al-Mg-Sc-Zr Alloy Subjected to Friction Stir Welding

2014 ◽  
Vol 922 ◽  
pp. 463-468
Author(s):  
Sergey Malopheyev ◽  
Vladislav Kulitskiy ◽  
Sergey Mironov ◽  
Daria Zhemchuzhnikova ◽  
Rustam Kaibyshev
Keyword(s):  
Friction Stir Welding ◽  
Strain Hardening ◽  
Initial Conditions ◽  
Welding Process ◽  
Weld Strength ◽  
Friction Stir ◽  
Joint Efficiency ◽  
Cold Rolled ◽  
Cold Worked ◽  
Hot Rolled

The microstructure and mechanical properties of friction stir welded Al-5.4Mg-0.2Sc-0.1Zr alloy were studied. Defect-free welds were produced in hot extruded, hot rolled and cold rolled initial conditions. Friction stir welding led to the formation of ultrafine-grained structure in stir zone that contributes to overall strengthening. Coherent Al3(Sc,Zr) dispersoids retain partially during welding process that provides a joint efficiency close to 100% in the hot extruded and hot rolled materials. In the cold-rolled state the joint efficiency was found to be only 64%. The relatively low weld strength of the cold rolled material was attributed to the elimination of strain hardening due to the formation of recrystallized structure. It was shown that full strength weld can be achieved in semi-finished products of Al-Mg-Sc alloys in cold-worked and stabilized states being equal to H323 and H341 tempering by friction stir welding.

scholarly journals Friction Stir Welding of an Al-Mg-Sc-Zr Alloy with Ultra-Fined Grained Structure

2014 ◽  
Vol 794-796 ◽  
pp. 365-370
Author(s):  
Sergey Malopheyev ◽  
Sergey Mironov ◽  
Vladislav Kulitskiy ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Weld Zone ◽  
Friction Stir ◽  
Angular Pressing ◽  
Joint Efficiency ◽  
Cold Rolled ◽  
Rolled Condition ◽  
Hot Rolled ◽  
Zr Alloy

Effect of friction stir welding (FSW) on mechanical properties and microstructure of Al-5.4Mg-0.2Sc-0.1Zr sheets with ultra-fined grained (UFG) structure was studied. The UFG-sheets were produced by equal-channel angular pressing (ECAP) followed either by cold or hot rolling. FSW was found to be very effective for retaining the UFG microstructure as well as constituent coherent nano-scale dispersoids in the welded material. Despite the preservation effect, however, the essential material softening was observed in the weld zone. This was attributed to the recrystallization occurring during FSW. The joint efficiency for yield strength of the obtained friction stir welds was found to be 81% in the hot rolled condition and only 55% in the cold rolled state. The relatively low joint efficiency was associated with the recrystallization softening as well as with the formation of a specific “kissing bond” defect in the stir zone. The joint efficiency is believed may be improved by adjusting of welding conditions and/or tool design.

scholarly journals The Effect of Vibration during Friction Stir Welding on Corrosion Behavior, Mechanical Properties, and Machining Characteristics of Stir Zone

Metals ◽  
2017 ◽  
Vol 7 (10) ◽  
pp. 421 ◽  
Author(s):  
Sajad Fouladi ◽  
Amir Ghasemi ◽  
Mahmoud Abbasi ◽  
Morteza Abedini ◽  
Amir Khorasani ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Corrosion Behavior ◽  
Stir Zone ◽  
Friction Stir ◽  
Machining Characteristics

Effect of plasma preheating on weld quality and tool life during friction stir welding of DH36 steel

2021 ◽  
pp. 095440542199013
Author(s):  
Avinish Tiwari ◽  
Pardeep Pankaj ◽  
Saurav Suman ◽  
Piyush Singh ◽  
Pankaj Biswas ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Tool Life ◽  
Force Measurement ◽  
Deep Understanding ◽  
High Strength ◽  
Microstructural Characterization ◽  
Stir Zone ◽  
Friction Stir ◽  
Allotriomorphic Ferrite ◽  
Fsw Parameters

Friction stir welding (FSW) of high strength materials is challenging due to high tool cost and low tool life. To address this issue, the present investigation deals with an alternative of plasma-assisted friction stir welding (PFSW) of DH36 steel with WC-10%Co tool. Plasma preheating current (13 A, 15 A, and 17 A) was varied by keeping other FSW parameters as constant. During the FSW and PFSW process, force measurement and thermal history aided in a deep understanding of the process, tool degradation mechanisms, accompanied by the mechanical and microstructural characterization of the welded joints. The stir zone hardness was increased from 140 HV0.5 to about 267 HV0.5. The yield and tensile strength of weld increased from 385 MPa and 514 MPa to about 391 MPa and 539 MPa, respectively. Weld joint elongation (%) was increased from ~10% of weld 1 to ~13.89% of weld 4. During PFSW, the process temperature was increased, the cooling rate was lowered, and the weld bead was widened. The results also revealed that the plasma-assisted weld resulted in polygonal ([Formula: see text]) and allotriomorphic ferrite as the major constituents in the stir zone. Pearlite dissolution and spheroidization were observed in the ICHAZ and SCHAZ, respectively. Additionally, the plasma preheating reduced the tungsten tool’s wear by 58% compared to FSW.

Stir zone material flow patterns during friction stir welding of heavy gauge AA5056 workpieces and stability of its mechanical properties

2021 ◽  
Vol 23 (4) ◽  
pp. 140-154
Author(s):  
Tatiana Kalashnikova ◽  
◽  
Vladimir Beloborodov ◽  
Kseniya Osipovich ◽  
Andrey Vorontsov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Elevated Temperatures ◽  
Thin Sheet ◽  
Stir Zone ◽  
Clear Correlation ◽  
Material Structure ◽  
Friction Stir ◽  
Significant Difference

Introduction. Friction stir welding and processing are almost identical processes of severe plastic deformation at elevated temperatures. These technologies differ mainly in the purpose of its use: the formation of a hardened surface layer or producing a welded joint. However, it is known that both during welding and during processing of heavy gauge workpieces temperature gradients occur. As a result, the conditions of adhesive interaction, material plastic flow, and the formation of the stir zone change as compared to thin-sheet workpieces with fundamentally different heat dissipation rates. In this connection, the purpose of the work is to determine the regularities of the structure formation and stability of the mechanical properties in different directions in the material of 35-mm-thick aluminum-magnesium alloy samples produced by friction stir welding/processing. Research Methodology. The technique and modes of friction stir welding and processing of AA5056 alloy workpieces with a thickness of 35 mm are described. Data on the equipment used for mechanical tests and structural research are given. Results and discussion. The data obtained show the excess mechanical properties of the processing zone material over the base metal ones in all studied directions. Material structure heterogeneities after friction stir welding/processing of heavy gauge workpieces have no determining effect on the stir zone properties. At the same time, there is no clear correlation between the tensile strength values and the load application direction, nor is there any significant difference in mechanical properties depending on the location of the samples inside the stir zone. The average ultimate tensile strength values in the vertical, transverse, and longitudinal directions are 302, 295 and 303 MPa, respectively, with the yield strength values of 155, 153 and 152 MPa, and the relative elongation of 27.2, 27.5, 28.7 %.

scholarly journals Research on the Friction Stir Welding of Sc-Modified AA2519 Extrusion

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1024 ◽  
Author(s):  
Robert Kosturek ◽  
Lucjan Śnieżek ◽  
Janusz Torzewski ◽  
Marcin Wachowski
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Base Material ◽  
Stir Zone ◽  
Welding Parameters ◽  
Friction Stir ◽  
Treated Condition ◽  
Heat Treated ◽  
Heat Treated Condition ◽  
Fsw Parameters

The aim of this research was to investigate the effect of friction stir welding (FSW) parameters on microstructure and mechanical properties of Sc-modified AA2519 extrusion joints. The workpiece was welded by FSW in non-heat-treated condition with seven different sets of welding parameters. For each obtained joint macrostructure and microstructure observations were performed. Mechanical properties of joints were investigated using tensile test together with localization of fracture location. Joint efficiencies were established by comparing measured joints tensile strength to the value for base material. The obtained results show that investigated FSW joints of Sc-modified AA2519 in the non-heat-treated condition have joint efficiency within the range 87–95%. In the joints obtained with the lowest ratio of the tool rotation speed to the tool traverse speed, the occurrence of imperfections (voids) localized in the stir zone was reported. Three selected samples were subjected to further investigations consisting microhardness distribution and scanning electron microscopy fractography analysis. As the result of dynamic recrystallization, the microhardness of the base material value of 86 HV0.1 increased to about 110–125 HV0.1 in the stir zone depending on the used welding parameters. Due to lack of the strengthening phase and low strain hardening of used alloy the lack of a significantly softened zone was reported by both microhardness analysis and investigation of the fractured samples.

scholarly journals Friction Stir Welding Parameters: Impact of Abnormal Grain Growth during Post-Weld Heat Treatment on Mechanical Properties of Al–Mg–Si Welded Joints

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1607
Author(s):  
Amir Hossein Baghdadi ◽  
Zainuddin Sajuri ◽  
Mohd Zaidi Omar ◽  
Armin Rajabi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Friction Stir Welding ◽  
Grain Growth ◽  
Precipitation Hardening ◽  
Al Alloys ◽  
Abnormal Grain Growth ◽  
Post Weld Heat Treatment ◽  
Welding Parameters ◽  
Friction Stir

Friction stir welding (FSW) is an alternative method to join aluminum (Al) alloys in a solid-state condition. However, the coarsening or dissolution of precipitation hardening phases in the welding zone causes strength reduction or softening behavior in the welded area of age-hardened Al alloys. Therefore, this research aimed to improve the mechanical properties of an FSW Al–Mg–Si alloy via post-weld heat treatment (PWHT) and the possibility of controlling the abnormal grain growth (AGG) using different welding parameters. FSW was performed with different rotational and travel speeds, and T6 heat treatment was carried out on the FSW samples as the PWHT. The results showed a decrease in the strength of the FSW samples compared with that of the base material (BM) due to the dissolution of precipitation hardening particles in the heat-affected zone. However, the emergence of AGG in the microstructure after the T6-PWHT was identified as the potential event in the microstructure of the PWHT samples. It is found that the AGG of the microstructure in similar joints of Al6061(T6) was governed by the welding parameters. The results proved that PWHT was able to increase the tensile properties of the welded samples to values comparable to that of Al6061(T6)-BM. The increased mechanical properties of the FSW joints were attributed to a proper PWHT that resulted in a homogeneous distribution of the precipitation hardening phases in the welding zones.

Sign in / Sign up

Export Citation Format

Share Document