Characteristics on Treated Kenaf Fiber Reinforced Polypropylene Composites

2017 ◽  
Vol 909 ◽  
pp. 94-99
Author(s):  
Muhammad Muslimin Husin ◽  
Mohammad Sukri Mustapa ◽  
Md. Saidin Wahab ◽  
Ahmad Mubarak Tajul Arifin ◽  
Reventheran A.L. Ganasan ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Alkali Treatment ◽  
Fiber Reinforced ◽  
Morphological Comparison ◽  
Kenaf Fiber ◽  
Polypropylene Composites ◽  
Composition Ratio ◽  
Tensile Performance ◽  
Test Press

Nowadays natural fiber and polymer matrix are being extensively used as alternatives in producing furniture like ceiling, floor and etc. to fulfill society demand instead of environmental friendly and saving cost. The objective of this study is to investigate the effects of maleic anhydride grafted polypropylene (MAPP) as a coupling agent for reinforcement between kenaf fiber (KF) and polypropylene (PP). The ratio of MAPP between 3% and 5% was observed to determine which composition ratio is better. The tensile strength for both 30% KF and 40% KF was treated through the alkali treatment process with 5% sodium hydroxide (NaOH). Kenaf fiber reinforced polypropylene (PP/KF) composites were melt blended and then used hydraulic molding test press machine for characterization to observe their tensile strengths by measuring their threshold. Tensile test was carried out to determine the tensile stresses of the composite at the best composition ratio of kenaf fiber that are 30% KF and 40% KF instead of MAPP ratio. The result shows 40% KF (5% MAPP) lead to better tensile performance compared to 40% KF (3% MAPP), 30% KF (5% MAPP) and 30% KF (3% MAPP). Meanwhile, Scanning electron microscopy (SEM) is used to observe the morphological comparison between untreated KF and treated KF as well as PP/KF. The good interfacial bonding between KF and PP was 5% MAPP rather than 3% MAPP due to the optimum strength received. Overall 5% MAPP with 40% PP/KF had shown the best result compared to others with the estimated tensile strength value of 21.38 MPa.

Impact of Alkali Treatment Conditions on Kenaf Fiber Polyester Composite Tensile Strength

2014 ◽  
Vol 660 ◽  
pp. 285-289 ◽  
Author(s):  
Mohd Yussni Hashim ◽  
Mohd Nazrul Roslan ◽  
Shahruddin Mahzan ◽  
Mohd Zin ◽  
Saparudin Ariffin
Keyword(s):  
Tensile Strength ◽  
Immersion Time ◽  
Natural Fiber ◽  
Alkali Treatment ◽  
Solution Temperature ◽  
Type I ◽  
Kenaf Fiber ◽  
Treatment Conditions ◽  
Polyester Composite ◽  
The Impact

The increase of environmental issues awareness has accelerated the utilization of renewable resources like plant fiber to be used as reinforced material in polymer composite. However, there are significant problems of compatibility between the fiber and the matrix due to weakness in the interfacial adhesion of the natural fiber with the synthetic matrices. One of the solutions to overcome this problem is using chemical modification like alkali treatment. In this study, the impact of alkali treatment conditions on short randomly oriented kenaf fiber reinforced polyester matrix composite tensile strength was investigated. The experimental design setting was based on 2 level factorial experiments. Two parameters were selected during alkali treatment process which are kenaf fiber immersion duration (at 30 minute and 480 minute) and alkali solution temperature (at 40°C and 80°C). Alkali concentration was fixed at 2% (w/v) and the kenaf polyester volume fraction ratio was 10:90. The composite specimens were tested to determine the tensile properties according to ASTM D638-10 Type I. JOEL scanning electron microscopy (SEM) was used to study the microstructure of the material. The result showed that alkali treatment conditions setting do have the impact on tensile strength of short randomly oriented kenaf polyester composite. The interaction factors between immersion time and temperature was found to have prominent factors to the tensile strength of composite followed by the immersion time factor.

scholarly journals STUDY OF THE EFFECT OF CHEMICAL TREATMENTS ON THE TENSILE BEHAVIOUR OF ABACA FIBER REINFORCED POLYPROPYLENE COMPOSITES

2014 ◽  
Vol 10 (6) ◽  
pp. 2814-2822
Author(s):  
Ramadevi Punyamurthy ◽  
Dhanalakshmi Sampathkumar ◽  
Basavaraju Bennehalli ◽  
Pramod V Badyankal
Keyword(s):  
Tensile Strength ◽  
Alkali Treatment ◽  
Tensile Tests ◽  
Tensile Behaviour ◽  
Fiber Reinforced ◽  
Compression Moulding ◽  
Polypropylene Composites ◽  
Chemical Treatments ◽  
Chloride Treatment ◽  
Benzene Diazonium

Abaca fibers were subjected to different chemical treatments like alkali treatment, permanganate treatment, acrylation & benzene diazonium chloride treatment and these chemically treated fibers were used as reinforcements in the preparation of polypropylene composites by hot compression moulding method. Various composites were fabricated with different fiber loadings of 20%, 30%, 40%, 50%, 60%, and 70%. Abaca composites with 40% fiber loadings were found to have optimum properties when tensile tests were carried out and the study also revealed that treated composites were found to have improved tensile properties when compared to untreated composites. Among all the treatments carried out benzene diazonium chloride treated abaca fiber reinforced polypropylene composites showed higher tensile strength. These composites showed 82.38% increase in tensile strength when compared to untreated composites for 40% fiber loading. 

Interfacial Modification of Hemp Fiber Reinforced Composites Using Fungal and Alkali Treatment

2007 ◽  
Vol 1 (1) ◽  
pp. 109-117 ◽  
Author(s):  
K. L. Pickering ◽  
Y. Li ◽  
R. L. Farrell ◽  
M. Lay
Keyword(s):  
Natural Fiber ◽  
Fiber Composite ◽  
Alkali Treatment ◽  
Natural Fibers ◽  
Fiber Reinforced ◽  
Hemp Fiber ◽  
Hemp Fibers ◽  
Polypropylene Composites ◽  
Interfacial Modification ◽  
Industrial Hemp

Increasing worldwide environmental awareness is encouraging scientific research into developing cheaper, more sustainable materials. Industrial hemp fiber is one of the strongest and stiffest available natural fibers [K. L. Pickering, M. Priest, T. Watts, G. Beckermann, and S. N. Alam, J. Adv. Mater. 37, 15 (2005)] and therefore has great potential in composite materials. Incorporated into a thermoplastic matrix, it gives a structural material that is cheap, lightweight, and recyclable. However, natural fibers are commonly incompatible with common molding thermoplastics such as polypropylene, which limits the performance of the composites produced. The main objective of the current work was to investigate the use of fungi to treat hemp fiber to create better bonding characteristics in natural fiber reinforced polypropylene composites. X-ray diffraction (XRD), ζ-potential, lignin testing, thermal analysis, and scanning electron microscopy (SEM) were used to characterize the effect of treatment on hemp fibers. A combined alkali and fungi treated fiber composite produced the highest tensile strength of 48.3 MPa, an increase of 32% compared to composites with untreated fiber.

Experimental and Numerical Study of the Critical Length of Short Kenaf Fiber Reinforced Polypropylene Composites

2020 ◽  
Vol 21 (4) ◽  
pp. 821-828 ◽  
Author(s):  
Mohammad Nematollahi ◽  
Mehdi Karevan ◽  
Marzieh Fallah ◽  
Mahmoud Farzin
Keyword(s):  
Numerical Study ◽  
Critical Length ◽  
Fiber Reinforced ◽  
Kenaf Fiber ◽  
Polypropylene Composites

scholarly journals Effects of High-Temperature Exposure on the Mechanical Properties of Kenaf Composites

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1643 ◽  
Author(s):  
Nabilah Afiqah Mohd Radzuan ◽  
Dulina Tholibon ◽  
Abu Bakar Sulong ◽  
Norhamidi Muhamad ◽  
Che Hassan Che Haron
Keyword(s):  
Mechanical Properties ◽  
Natural Fiber ◽  
Molding Process ◽  
Kenaf Fiber ◽  
Polypropylene Composites ◽  
Safety Issues ◽  
Automotive Parts ◽  
Kenaf Composites ◽  
Temperature Exposure ◽  
Kenaf Fibers

Automotive parts, including dashboards and trunk covers, are now fabricated through a compression-molding process in order to produce lightweight products and optimize fuel consumption. However, their mechanical strength is not compromised to avoid safety issues. Therefore, this study investigates kenaf-fiber-reinforced polypropylene composites using a simple combing approach to unidirectionally align kenaf fibers at 0°. The kenaf composite was found to withstand a maximal temperature of 120 °C. The tensile and flexural strengths of the aligned kenaf composites (50 and 90 MPa, respectively) were three times higher than those of the commercialized Product T (between 39 and 30.5 MPa, respectively) at a temperature range of 90 to 120 °C. These findings clearly showed that the mechanical properties of aligned kenaf fibers fabricated through the combing technique were able to withstand high operating temperatures (120 °C), and could be used as an alternative to other commercial natural-fiber products.

scholarly journals Effects of Waste Expanded Polypropylene as Recycled Matrix on the Flexural, Impact, and Heat Deflection Temperature Properties of Kenaf Fiber/Polypropylene Composites

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2578
Author(s):  
Junghoon Kim ◽  
Donghwan Cho
Keyword(s):  
Impact Strength ◽  
Natural Fiber ◽  
Flexural Modulus ◽  
Fiber Composites ◽  
Kenaf Fiber ◽  
Polypropylene Composites ◽  
Izod Impact ◽  
Pp Composites ◽  
Heat Deflection Temperature ◽  
Kenaf Fibers

Waste Expanded polypropylene (EPP) was utilized as recycled matrix for kenaf fiber-reinforced polypropylene (PP) composites produced using chopped kenaf fibers and crushed EPP waste. The flexural properties, impact strength, and heat deflection temperature (HDT) of kenaf fiber/PP composites were highly enhanced by using waste EPP, compared to those by using virgin PP. The flexural modulus and strength of the composites with waste EPP were 98% and 55% higher than those with virgin PP at the same kenaf contents, respectively. The Izod impact strength and HDT were 31% and 12% higher with waste EPP than with virgin PP, respectively. The present study indicates that waste EPP would be feasible as recycled matrix for replacing conventional PP matrix in natural fiber composites.

Fabrication of Chemically Treated Natural Fibre Reinforced Polymer Matrix Composites and Measurement of its Sound Absorption Coefficients to Regulate Industrial Noise

2013 ◽  
Vol 465-466 ◽  
pp. 896-900
Author(s):  
Elammaran Jayamani ◽  
Pushparaj Ezhumalai ◽  
Sinin Hamdan ◽  
M. Rezaur Rahman
Keyword(s):  
Rice Straw ◽  
Sound Absorption ◽  
Natural Fiber ◽  
Polymer Matrix Composites ◽  
Fiber Reinforced ◽  
Absorption Coefficients ◽  
Compression Moulding ◽  
Industrial Noise ◽  
Polypropylene Composites ◽  
Chemically Treated

The effects of chemically treated natural fibres (rice straw and kenaf) embedded as filler into polypropylene matrix were investigated for its sound absorption properties to regulate the industrial noise. In this respect, untreated natural fiber as well as treated natural fiber reinforced with polypropylene composites were fabricated and compared. The composites were prepared by compression moulding technique. Its sound absorbing characteristic was investigated with the Impedance tube, according to a transfer function method. A two microphone setup was fabricated according to American society for testing materials ASTM E1050-10 and it is used to measure sound absorption coefficients of composites in the frequency range of 300 Hz to 2000 Hz. The sound absorption coefficients of the composites increased with the frequency. However, at 1000 Hz, the sound absorption coefficient decreased for all treated samples and then increased again which is due to specific character of natural fibers. This point of inflexion was due to the specific characteristic of natural fiber reflecting sound at around 1000 Hz, but absorbing sound in the middle and high frequencies. The results indicates that the process of chemical treatment enhanced the sound absorption coefficients by 12.5% for rice straw reinforced Polypropylene and 15.78% for kenaf fiber reinforced Polypropylene composites respectively.

Sign in / Sign up

Export Citation Format

Share Document