The Operator Protective Structures Testing for Mining Machines

2010 ◽  
Vol 165 ◽  
pp. 256-261 ◽  
Author(s):  
Damian Derlukiewicz ◽  
Jacek Karliński ◽  
Artur Iluk
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Numerical Simulations ◽  
Computational Models ◽  
Experimental Tests ◽  
Passive Safety ◽  
Protective Structure ◽  
Simulation Results ◽  
Protective Structures ◽  
Element Method

The study presents selected problems concerning the testing of protective structures for the mining machines in the field of passive safety. Such machines equipped with protective structures must meet the requirements of the relevant regulations and standards. Requirements of conducting experimental tests of protective structures: FOPS, ROPS and RSPS are specified. The paper provides the principles of development of computational models for numerical simulations by means of finite element method. A detailed example of comparison of experimental and simulation results for a protective structure is presented.

scholarly journals Imaging Mueller matrix ellipsometry setup for optical nanoform metrology

2020 ◽  
Vol 238 ◽  
pp. 06006
Author(s):  
Tim Käseberg ◽  
Jana Grundmann ◽  
Johannes Dickmann ◽  
Stefanie Kroker ◽  
Bernd Bodermann
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Numerical Simulations ◽  
Mueller Matrix ◽  
The Finite Element Method ◽  
Mueller Matrices ◽  
Microscope Images ◽  
Element Method

We designed, realized, and characterised an imaging Mueller matrix ellipsometry setup for the pixelwise measurement of the Mueller matrices in microscope images. Our setup is capable of performing measurements in reflection as well as in transmission in a broad range of angles of incidence for wavelengths between 400 nm and 700 nm. We compared measurements of specially designed nanostructured samples with AFM and SEM measurements as well as with numerical simulations using the finite element method.

scholarly journals Cold Expansion Process with Multiple Balls—Numerical Simulation and Comparison with Single Ball and Tapered Mandrels

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5536
Author(s):  
David Curto-Cárdenas ◽  
Jose Calaf-Chica ◽  
Pedro Miguel Bravo Díez ◽  
Mónica Preciado Calzada ◽  
Maria-Jose Garcia-Tarrago
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Fatigue Life ◽  
Experimental Tests ◽  
The Finite Element Method ◽  
Expansion Process ◽  
Cold Expansion ◽  
Hoop Stresses ◽  
Element Method

Cold expansion technology is an extended method used in aeronautics to increase fatigue life of holes and hence extending inspection intervals. During the cold expansion process, a mechanical mandrel is forced to pass along the hole generating compressive residual hoop stresses. The most widely accepted geometry for this mandrel is the tapered one and simpler options like balls have generally been rejected based on the non-conforming residual hoop stresses derived from their use. In this investigation a novelty process using multiple balls with incremental interference, instead of a single one, was simulated. Experimental tests were performed to validate the finite element method (FEM) models and residual hoop stresses from multiple balls simulation were compared with one ball and tapered mandrel simulations. Results showed that the use of three incremental balls significantly reduced the magnitude of non-conforming residual hoop stresses and the extension of these detrimental zone.

A study of azimuthal electromagnetic wave LWD based on self-adaptive hp finite element method

2018 ◽  
Vol 32 (34n36) ◽  
pp. 1840073
Author(s):  
Hui Li ◽  
Yi-Bo Jiang ◽  
Jian-Wen Cai
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Electromagnetic Wave ◽  
Real Time ◽  
Simulation Results ◽  
Peak Value ◽  
Element Method ◽  
Self Adaptive ◽  
Hp Finite Element

Azimuthal electromagnetic wave logging-while-drilling (LWD) technology can detect weak electromagnetic wave signal and realize real-time resistivity imaging. It has great values to reduce drilling cost and increase drilling rate. In this paper, self-adaptive hp finite element method (FEM) has been used to study the azimuthal resistivity LWD responses in different conditions. Numerical simulation results show that amplitude attenuation and phase shift of directional electromagnetic wave signals are closely related to induced magnetic field and azimuthal angle. The peak value and polarity of geological guidance signals can be used to distinguish reservoir interface and achieve real-time geosteering drilling. Numerical simulation results also show the accuracy of the self-adaptive hp FEM and provide physical interpretation of peak value and polarity of the geological guidance signals.

A Tunable THz Plasmonic Waveguide Based on Graphene Coated Bow-tie Nanowire with High Mode Confinement

2020 ◽  
Vol 12 ◽  
Author(s):  
Jue Wang ◽  
Tao Ma ◽  
Xu Wang ◽  
Fang Wang
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Electric Field ◽  
High Density ◽  
Plasmonic Waveguide ◽  
Field Distributions ◽  
Simulation Results ◽  
Photonic Circuit ◽  
Bow Tie ◽  
Element Method

Background: : A THz Plasmonic Waveguide Based on Graphene Coated Bow-tie Nanowire (TPW-GCBN) is proposed. The waveguide characteristics are investigated by using Finite Element Method (FEM). The influence of the geometric parameters on propagation constants, electric field distributions, effective mode areas, and propagation lengths are obtained numerically. The performance tunability of TPW-GCBN is also studied by adjusting the Fermi energy (FE). The simulation results show that the TPW-GCBN has better mode confinement ability. The TPW-GCBN has potential applications in high density integration of photonic circuit for the future tunable micro nano optoelectronic devices. Surface plasmon polaritons (SPPs) based waveguides have been widely used to enhance the local electric fields. It also has the capability of manipulating electromagnetic fields on the deep-subwavelength. Objective:: The waveguide characteristics of a THz Plasmonic Waveguide Based on Graphene Coated Bow-tie Nanowire (TPW-GCBN) should be investigated. The tunability of TPW-GCBN should be studied by adjusting the chemical potential (FE) which can be changed by the voltage. Method: : The mode analysis and parameter sweep in Finite Element Method (FEM) were used to simulate the TPW-GCBN for analyzing effective refractive index (neff), electric field distributions, normalized mode areas (Am), propagation length (Lp) and figure of merit (FoM). Results: : At 5 THz, Aeff of λ2/14812, Lp of ~2 μm and FoM of 25 can be achieved. The simulation results show that the TPW-GBN has good mode confinement ability and flexible tunability. Conclusion:: The TPW-GBN provides a new freedom to manipulate the graphene surface plasmons, and leads to new applications in high density integration of photonic circuit for tunable integrated optical devices.

Dynamic tensile process of blended fabric using finite element method

2020 ◽  
Vol 32 (5) ◽  
pp. 707-724
Author(s):  
Xuzhong Su ◽  
Xinjin Liu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Experimental Testing ◽  
Woven Fabrics ◽  
Weft Yarn ◽  
Tensile Fracture ◽  
Content Type ◽  
Tensile Process ◽  
Simulation Results ◽  
Element Method

PurposeTensile property is one basic mechanics performance of the fabric. In general, not only the tensile values of the fabric are needed, but also the dynamic changing process under the tension is also needed. However, the dynamic tensile process cannot be included in the common testing methods by using the instruments after fabric weaving.Design/methodology/approachBy choosing the weft yarn and warp yarn in the fabric as the minimum modeling unit, 1:1 finite element model of the whole woven fabrics was built by using AutoCAD software according to the measured geometric parameters of the fabrics and mechanical parameters of yarns. Then, the fabric dynamic tensile process was simulated by using the ANSYS software. The stress–strain curve along the warp direction and shrinkage rate curve along the weft direction of the fabrics were simulated. Meanwhile, simulation results were verified by comparing to the testing results.FindingsIt is shown that there are four stages during the fabric tensile fracture process along the warp direction under the tension. The first stage is fabric elastic deformation. The second stage is fabric yield deformation, and the change rate of stress begins to slow down. The third stage is fiber breaking, and the change of stress fluctuates since the breaking time of the fibers is different. The fourth stage is fabric breaking.Originality/valueIn this paper, the dynamic tensile process of blended woven fabrics was studied by using finite element method. Although there are differences between the simulation results and experimental testing results, the overall tendency of simulation results is the same as the experimental testing results.

scholarly journals New CZM for Interfacial Crack Growth

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Huifen Peng ◽  
Yujie Song ◽  
Ye Xia
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Crack Growth ◽  
Interface Crack ◽  
Interfacial Crack ◽  
Structure Design ◽  
Zone Model ◽  
Simulation Results ◽  
The Impact ◽  
Element Method

The cohesive zone model (CZM) has been widely used for numerical simulations of interface crack growth. However, geometrical and material discontinuities decrease the accuracy and efficiency of the CZM when based on the conventional finite element method (CFEM). In order to promote the development of numerical simulation of interfacial crack growth, a new CZM, based on the wavelet finite element method (WFEM), is presented. Some fundamental issues regarding CZM of interface crack growth of double cantilever beam (DCB) testing were studied. The simulation results were compared with the experimental and simulation results of CFEM. It was found that the new CZM had higher accuracy and efficiency in the simulation of interface crack growth. At last, the impact of crack initiation length and elastic constants of material on interface crack growth was studied based on the new CZM. These results provided a basis for reasonable structure design of composite material in engineering.

The Numerical Simulation of Effective Elastic Response for WC-Co Cemented Carbide

2015 ◽  
Vol 1096 ◽  
pp. 417-421
Author(s):  
Pei Luan Li ◽  
Zi Qian Huang
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Theoretical Model ◽  
Material Properties ◽  
Cemented Carbide ◽  
Elastic Response ◽  
The Finite Element Method ◽  
Simulation Results ◽  
Element Method

By the use of finite element method, this paper predicts the effects of the shapes of reinforcements with different ductility (Co) on the effective elastic response for WC-Co cemented carbide. This paper conducts a comparative study on the material properties obtained through theoretical model, numerical simulation and experimental observations. Simulation results indicate that the finite element method is more sophisticated than the theoretical prediction.

Sign in / Sign up

Export Citation Format

Share Document