scholarly journals Castor Oil: Properties, Uses, and Optimization of Processing Parameters in Commercial Production

2016 ◽  
Vol 9 ◽  
pp. LPI.S40233 ◽  
Author(s):  
Vinay R. Patel ◽  
Gerard G. Dumancas ◽  
Lakshmi C. Kasi Viswanath ◽  
Randall Maples ◽  
Bryan John J. Subong

Castor oil, produced from castor beans, has long been considered to be of important commercial value primarily for the manufacturing of soaps, lubricants, and coatings, among others. Global castor oil production is concentrated primarily in a small geographic region of Gujarat in Western India. This region is favorable due to its labor-intensive cultivation method and subtropical climate conditions. Entrepreneurs and castor processors in the United States and South America also cultivate castor beans but are faced with the challenge of achieving high castor oil production efficiency, as well as obtaining the desired oil quality. In this manuscript, we provide a detailed analysis of novel processing methods involved in castor oil production. We discuss novel processing methods by explaining specific processing parameters involved in castor oil production.

2021 ◽  
Vol 9 ◽  
Author(s):  
Lara Valderrama ◽  
Salvador Ayala ◽  
Carolina Reyes ◽  
Christian R. González

The extreme north of Chile presents a subtropical climate permissive of the establishment of potential disease vectors. Anopheles (Ano.) pseudopunctipennis is distributed from the south of the United States to the north of Argentina and Chile, and is one of the main vectors of malaria in Latin America. Malaria was eradicated from Chile in 1945. Nevertheless, the vector persists in river ravines of the Arica and Tarapacá regions. The principal effect of climate change in the north of Chile is temperature increase. Precipitation prediction is not accurate for this region because records were erratic during the last century. The objective of this study was to estimate the current and the projected distribution pattern of this species in Chile, given the potential impact due to climate change. We compiled distributional data for An. (Ano.) pseudopunctipennis and constructed species distribution models to predict the spatial distribution of this species using the MaxEnt algorithm with current and RCP 4.5 and 8.5 scenarios, using environmental and topographic layers. Our models estimated that the current expected range of An. (Ano.) pseudopunctipennis extends continuously from Arica to the north of Antofagasta region. Furthermore, the RCP 4.5 and 8.5 projected scenarios suggested that the range of distribution of An. (Ano.) pseudopunctipennis may increase in longitude, latitude, and altitude limits, enhancing the local extension area by 38 and 101%, respectively, and local presence probability (>0.7), from the northern limit in Arica y Parinacota region (18°S) to the northern Antofagasta region (23°S). This study contributes to geographic and ecologic knowledge about this species in Chile, as it represents the first local study of An. (Ano.) pseudopunctipennis. The information generated in this study can be used to inform decision making regarding vector control and surveillance programs of Latin America. These kinds of studies are very relevant to generate human, animal, and environmental health knowledge contributing to the “One Health” concept.


Author(s):  
S. A. Zolina ◽  
I. A. Kopytin ◽  
O. B. Reznikova

In 2018 the United States surpassed Saudi Arabia and Russia to become the largest world oil producer. The article focuses on the mechanisms through which the American shale revolution increasingly impacts functioning of the world oil market. The authors show that this impact is translated to the world oil market mainly through the trade and price channels. Lifting the ban on crude oil exports in December 2015 allowed the United States to increase rapidly supply of crude oil to the world oil market, the country’s share in the world crude oil exports reached 4,4% in 2018 and continues to rise. The U.S. share in the world petroleum products exports, on which the American oil sector places the main stake, reached 18%. In parallel with increasing oil production the U.S. considerably shrank crude oil import that forced many oil exporters to reorient to other markets. Due to high elasticity of tight oil production to the oil price increases oil from the U.S. has started to constrain the world oil price from above. According to the majority of authoritative forecasts, oil production in the U.S. will continue to increase at least until 2025. Since 2017 the tendency to the increasing expansion of supermajors into American unconventional oil sector has become noticeable, what will contribute to further strengthening of the U.S. position in the world oil market and accelerate its restructuring.  


2021 ◽  
pp. 131-143
Author(s):  
F. A. Koryakin ◽  
N. Yu. Tretyakov ◽  
O. B. Abdulla ◽  
V. G. Filippov

Nowadays the share of hard-to-recover reserves is growing, and to maintain oil production on necessarily level, we need to involve hard-to-recover reserves or to increase oil production efficiency on a brownfields due to enhanced oil recovery. The efficiency of enhanced oil recovery can be estimated by oil saturation reduction. Single-well-chemical-tracer-test (SWCTT) is increasingly used to estimate oil saturation before and after enhanced oil recovery application. To interpret results of SWCTT, reservoir simulation is recommended. Oil saturation has been calculated by SWCTT interpretation with use of reservoir simulator (CMG STARS). Distribution constants has been corrected due to results of real core sample model, and core tests has been successfully simulated. Obtained values of oil saturation corresponds with real oil saturation of samples. Thus, SWCTT as a method of oil saturation estimation shows good results. This method is promising for enhanced oil recovery efficiency estimation.


1981 ◽  
Vol 8 (1) ◽  
pp. 5-18 ◽  
Author(s):  
Douglas Argyle Campbell

This survey has described the foreseeable environmental and economic impacts of enhanced oil-recovery (EOR) on U.S. oil production between 1980 and 2000. It has indicated that EOR production may be expected to rise from the approximately 4% of total U.S. oil production in 1980, to the projected approximations of 10.5% in 1985, 18.5% in 1990, 23% in 1995, and perhaps 30% in 2000. These percentages are substantial, particularly as this form of oil production has been, up until recently, quite limited. Many of the processes are still in the laboratory stage of development—particularly chemical and microbiological processes. With continued laboratory experimentation and field research, it is possible that the percentages could be even greater than the above suggestions as we reach into the 21st Century.The potential for EOR is very considerable and probably great, as it could involve some two-thirds of all the oil already identified in the United States and assumed to be unrecoverable by primary or secondary means. The U.S. Department of Energy (DOE) has given important incentives to the EOR industry to make such increased production worth while through raising prices to compensate for the cost of equipment, and deducting expenditure on such equipment from a new ‘Windfall Profit Tax’.Along with EOR's economic potential, there are two major ecological dangers: air pollution through thermal processes, and ground-water pollution through chemical processes. It is essential to the well-being of the United States that clean air standards be adhered to, and that the equipment necessary to purify the air (particularly in California) be available and operate to reduce emissions.A great deal more research needs to be undertaken towards developing safeguards to ensure that drinkingwater is not contaminated by dangerous chemicals which may be used in ‘chemical flooding’ of depleted oil-wells. Many of these chemicals have merely ‘come out of the laboratory’ and are sold by chemical companies without sufficient field-testing. How far these chemicals could travel underground must still be determined. It is also important to ensure that carbon dioxide, fed into a geological formation, can be recaptured and re-injected without escaping into the atmosphere, where there is the potential danger of a global ‘greenhouse effect’ upon the world's temperature. Finally, it is important to safeguard the Earth against microbes which could be injected into its geological strata without sufficient knowledge of their impact on the ecology of the Earth. Thus, much environmental research will be called for with these new methods of producing oil for Man's use.This study has reviewed the four major methods of EOR that are currently being utilized or proposed— thermal processes, miscible and semi-miscible processes, chemical processes, and microbiological processes, and found that they could all have ongoing possibilities.Given appropriate environmental safeguards, EOR should become a major force in the production of energy for the United States over the next 20 years, and it seems reasonable to expect that much the same could apply to other parts of the world. However, it is important that safeguarding the environment should guide the DOE in terms of its incentive programmes for specific processes.


2011 ◽  
Vol 325 ◽  
pp. 375-380 ◽  
Author(s):  
Gui Yu Li ◽  
Jian Feng Li ◽  
Jie Sun

Drilling parameters have great influences on hole accuracy and defect production. In this study, single factor test is applied to obtain the relationship between the torque deviation and the spindle speed n at different feeds per revolution fr. White Light Interferometer (WLI) is applied to measure the hole shape. Based on the frequency domain analysis of torque deviation, the cause of hole shape deviation is investigated. Relationship between the hole shape accuracy and drilling parameters is established, which can be used to predict the hole shape by analyzing the torque deviation. Moreover, the reasonable processing parameters can be selected to obtain drilling hole with ideal shape and satisfying production efficiency.


2011 ◽  
Vol 415-417 ◽  
pp. 825-830
Author(s):  
Zhen Yi Huang ◽  
Yi Qian Wang ◽  
You He Li ◽  
Ping Wang ◽  
Xiao Feng Zhang

Abstract. This paper had an improvement research on the annealing process of AISI4145H steel by changing the processing parameters of heat treatment in laboratory. An experimental physical simulation was conducted between 650 °C and 740 °C. The effect upon the hardness of AISI4145H steel under different temperature and holding time investigated. And the condition of Φ 150 mm AISI4145H steel that was heated and warmed up in an annealing furnace was tested by adopting a black box. Results showed that the Ac1 of AISI4145H steel was 757.2 °C and the Ac3 was 787.7 °C. By the annealed conditions that sample was heated at 710 °C for 1h, cooled to 500 °C in furnace and cooled in air in turn, we found its hardness was HRC 21.4 and meet the needs of industrial production. New process of the present work shortened holding time of workpiece, increased cooling rate of annealed, shortened the annealed time about 24 h, effectively increased production efficiency, and reduced production costs.


2006 ◽  
Vol 98 (4) ◽  
pp. 797-805 ◽  
Author(s):  
Paolo Amirante ◽  
Maria Lisa Clodoveo ◽  
Giacomo Dugo ◽  
Alessandro Leone ◽  
Antonia Tamborrino

Sign in / Sign up

Export Citation Format

Share Document