Gas Metal Arc Welding of Coated Advanced High Strength Steel (AHSS) - Developments for Improved Weld Quality

2007 ◽  
Author(s):  
A. Joaquin ◽  
A. N. A. Elliott ◽  
C. Jiang ◽  
V. Rajan ◽  
D. Hartman ◽  
...  
Keyword(s):  
High Strength Steel ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
High Strength ◽  
Weld Quality ◽  
Advanced High Strength Steel ◽  
Metal Arc Welding

scholarly journals Optimization of Parameters on Robotized Gas Metal Arc Welding of LNE 700 High-Strength Steel

2018 ◽  
Vol 2 (4) ◽  
pp. 70
Author(s):  
Richard Lermen ◽  
Anderson Dal Molin ◽  
Djeison Berger ◽  
Valtair Alves ◽  
Camila Lisboa
Keyword(s):  
Experimental Design ◽  
High Strength Steel ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Quality Criteria ◽  
High Strength ◽  
Welding Parameters ◽  
Advanced High Strength Steel ◽  
Optimization Of Parameters ◽  
Metal Arc Welding

The main aim of this study is to determine the best process parameters for the robotized Gas Metal Arc Welding (GMAW) of LNE 700 advanced high-strength steel. This article evaluates some quality criteria such as the microhardness, the heat-affected zone (HAZ) and the convexity in the welded joints. The assays are performed using an experimental design, based on the Taguchi method. The analysis of the results identified some factors of greatest influence and how best to combine them to determine an optimum condition for welding LNE 700 high strength steel. Moreover, the influence of welding parameters on quality criteria is determined.

scholarly journals Porosity Characteristics and Effect on Tensile Shear Strength of High-Strength Galvanized Steel Sheets after the Gas Metal Arc Welding Process

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 1077 ◽  
Author(s):  
Seungmin Shin ◽  
Sehun Rhee
Keyword(s):  
Shear Strength ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
High Strength ◽  
Galvanized Steel ◽  
Tensile Shear Strength ◽  
Tensile Shear ◽  
Tensile Test Specimen ◽  
Metal Arc Welding

In this study, lap joint experiments were conducted using galvanized high-strength steel, SGAFH 590 FB 2.3 mmt, which was applied to automotive chassis components in the gas metal arc welding (GMAW) process. Zinc residues were confirmed using a semi-quantitative energy dispersive X-ray spectroscopy (EDS) analysis of the porosity in the weld. In addition, a tensile shear test was performed to evaluate the weldability. Furthermore, the effect of porosity defects, such as blowholes and pits generated in the weld, on the tensile shear strength was experimentally verified by comparing the porosity at the weld section of the tensile test specimen with that measured through radiographic testing.

Fracture Mechanics of Conventional and Narrow Groove Pulse Current Gas Metal Arc Welds of HSLA Steel

2012 ◽  
Vol 710 ◽  
pp. 451-456
Author(s):  
Ravi Ranjan Kumar ◽  
P. K. Ghosh
Keyword(s):  
Fracture Toughness ◽  
Weld Metal ◽  
Tensile Properties ◽  
Arc Welding ◽  
Hsla Steel ◽  
Gas Metal Arc Welding ◽  
High Strength ◽  
Compact Tension ◽  
Shielded Metal Arc Welding ◽  
Metal Arc Welding

Mechanical and fracture properties of 20MnMoNi55 grade high strength low alloy (HSLA) steel welds have been studied. The weld joints were made using Gas Tungsten Arc Welding (GTAW), Shielded Metal Arc Welding (SMAW) and Pulse Gas Metal Arc Welding (P-GMAW) methods on conventional V-groove (V-Groove) and Narrow groove (NG-13). The base metal and weld metal were characterised in terms of their metallurgical, mechanical and fracture toughness properties by following ASTM procedures. The J-Integral fracture test was carried out using compact tension C(T) specimen for base and weld metal. The fracture toughness and tensile properties of welds have been correlated with microstructure. In conventional V-groove welds prepared by P-GMAW shows the improvement in initiation fracture toughness (JIC) as compared to the weld prepared by SMAW. Similar improvements in tensile properties have also been observed. This is attributed to reduction in co-axial dendrite content due to lower heat input during P-GMAW process as compared to SMAW. In the narrow groove P-GMA weld prepared at f value of 0.15 has shown relative improvement of JIC as compared to that of the weld prepared by SMAW process.

scholarly journals Pulse spray gas metal arc welding of advanced high strength S650MC automotive steel

10.30544/682 ◽  
2021 ◽  
Vol 27 (4) ◽  
pp. 505-517
Author(s):  
Ashok Kumar Srivastava ◽  
Pradip K Patra
Keyword(s):  
Weld Joint ◽  
Heat Input ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
High Strength Steels ◽  
High Strength ◽  
Filler Wire ◽  
Advanced High Strength Steels ◽  
Metal Arc Welding ◽  
The Impact

With an increasing demand for safer and greener vehicles, mild steel and high strength steel are being replaced by much stronger advanced high strength steels of thinner gauges. However, the welding process of advanced high strength steels is not developed at the same pace. The performance of these welded automotive structural components depends largely on the external and internal quality of weldment. Gas metal arc welding (GMAW) is one of the most common methods used in the automotive industry to join car body parts of dissimilar high strength steels. It is also recognized for its versatility and speed. In this work, after a review of GMAW process and issues in welding of advanced high strength steels, a welding experiment is carried out with varying heat input by using spray and pulse-spray transfer GMAW method with filler wires of three different strength levels. The experiment results, including macro-microstructure, mechanical properties, and microhardness of weld samples, are investigated in detail. Very good weldability of S650MC is demonstrated through the weld joint efficiency > 90%; no crack in bending of weld joints, or fracture of tensile test sample within weld joint or heat affected zone (HAZ), or softening of the HAZ. Pulse spray is superior because of thinner HAZ width and finer microstructure on account of lower heat input. The impact of filler wire strength on weldability is insignificant. However, high strength filler wire (ER100SG) may be chosen as per standard welding practice of matching strength.

Microstructure and fatigue resistance of high strength dual phase steel welded with gas metal arc welding and plasma arc welding processes

2013 ◽  
Vol 19 (5) ◽  
pp. 933-939 ◽  
Author(s):  
Godwin Kwame Ahiale ◽  
Yong-Jun Oh ◽  
Won-Doo Choi ◽  
Kwang-Bok Lee ◽  
Jae-Gyu Jung ◽  
...  
Keyword(s):  
Fatigue Resistance ◽  
Arc Welding ◽  
Dual Phase Steel ◽  
Gas Metal Arc Welding ◽  
High Strength ◽  
Dual Phase ◽  
Plasma Arc Welding ◽  
Plasma Arc ◽  
Metal Arc Welding ◽  
Welding Processes

Microcrack Formation During Gas Metal Arc Welding of High-Strength Fine-Grained Structural Steel

2014 ◽  
Vol 27 (1) ◽  
pp. 140-148 ◽  
Author(s):  
Christoph Heinze ◽  
Thomas Michael ◽  
Andreas Pittner ◽  
Michael Rethmeier
Keyword(s):  
Structural Steel ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
High Strength ◽  
Fine Grained ◽  
Metal Arc Welding ◽  
Microcrack Formation
Sign in / Sign up

Export Citation Format

Share Document