Enabling Much Higher Power Densities in Aerospace Power Electronics with High Temperature Evaporative Spray Cooling

Author(s):  
Louis J. Turek ◽  
Daniel P. Rini ◽  
Benjamin A. Saarloos ◽  
Louis C. Chow
2003 ◽  
Vol 764 ◽  
Author(s):  
C.-M. Zetterling ◽  
S.-M. Koo ◽  
E. Danielsson ◽  
W. Liu ◽  
S.-K. Lee ◽  
...  

AbstractSilicon carbide has been proposed as an excellent material for high-frequency, high-power and high-temperature electronics. High power and high frequency applications have been pursued for quite some time in SiC with a great deal of success in terms of demonstrated devices. However, self-heating problems due to the much higher power densities that result when ten times higher electrical fields are used inside the devices needs to be addressed. High-temperature electronics has not yet experienced as much attention and success, possibly because there is no immediate market. This paper will review some of the advances that have been made in high-temperature electronics using silicon carbide, starting from process technology, continuing with device design, and finishing with circuit examples. For process technology, one of the biggest obstacles is long-term stable contacts. Several device structures have been electrically characterized at high temperature (BJTs and FETs) and will be compared to surface temperature measurements and physical device simulation. Finally some proposed circuit topologies as well as novel solutions will be presented.


Author(s):  
George Papadopoulos ◽  
Daniel Kearney ◽  
Daniele Torresin

The field of consumer and power electronics is surging ahead with more sophisticated and powerful devices that are smaller and more capable than before. Proper and efficient thermal management of such devices is increasingly challenging when addressing requirements to reduce size, weight and cost (both manufacturing and operational) while enabling the overall system to operate at higher power densities. The current effort considers a typical power electronic module most often used to address DC to AC voltage conversion in larger distributed energy systems. Significant heat generation results from switching and conduction losses inherent in such a circuit, which can then cause a drop in the power processing capabilities or worse, the destruction of the device itself if not properly cooled. A nominal architecture for the circuit module is selected and a combined experimental and analytical study is performed to implement an integrated micro-cooling chip architecture that leverages single phase jet-impingement and vortex flow approaches. The micro-cooling chip array is a multi-laminate design that features localized fluidic cells ducted to bring coolant in and out of a heat exchanger section. The paper reports on the design of the multi-laminate micro-cooling chip module in terms of manufacturability and fluid dynamics of the coolant in combination with the power electronics module. Results from bench-scale testing done on a monolithic part fabricated using additive manufacturing process are reported and compared with analysis. The results provide an initial basis for further miniaturization of the power electronic module and insights to manufacturability using standard 3D printing approaches.


A study is made of the means by which plasmas used for generating m.h.d. power may be modulated in order to provide higher power densities. Temperature and/or velocity modulation may be obtained in a quasi-steady flow combustion system, e.g. by introducing striations of high temperature fluid, or in a non-steady system by exciting pulsations or oscillations. Studies on striations are outlined and the relevant work on non-steady modulation is discussed. A description is given of the joint work at Sheffield University on an oscillatory vortex m.h.d.generator (Sheffield) and a proposed linear m.h.d. system (Queen Mary College, London).


Author(s):  
Mustafa Bulut Coskun ◽  
Mahmut Faruk Aksit

With the race for higher power and efficiency new gas turbines operate at ever increasing pressures and temperatures. Increased compression ratios and firing temperatures require many engine parts to survive extended service hours under large pressure loads and thermal distortions while sustaining relative vibratory motion. On the other hand, wear at elevated temperatures limits part life. Combined with rapid oxidation for most materials wear resistance reduces rapidly with increasing temperature. In order to achieve improved wear performance at elevated temperatures better understanding of combined wear and oxidation behavior of high temperature super alloys and coatings needed. In an attempt to aid designers for high temperature applications, this work provides a quick reference for the high temperature friction and wear research available in open literature. High temperature friction and wear data have been collected, grouped and summarized in tables.


2015 ◽  
Author(s):  
Jon W. Teets ◽  
J. Michael Teets

A SUNTRACKER (illustrated in figure1), is a Concentrating Solar Power (CSP) unit, in the category of solar dish engines. The novel solar dish engine module (shown in figure 2) is designed to provide 10.1kW electric power (measured at the engine output electric power lugs), from a conversion of 21kW solar energy from the solar dish reflective sun light to the high temperature receiver focal point. Total electric power output from the solar dish engine module is attributed to combined cycles, closed brayton cycle (CBC) and a organic rankine cycle (ORC), both of which are hermetically sealed to atmosphere. The CBC engine receives 21kW solar energy from a solar dish, estimated to have 27 square meters (291 square feet) reflective surface area. However, unlike the photovoltaic (PV) units, the SUNTRACKER will provide increased use of available solar energy from sunlight. Concentrated sunlight from the dish will focus on the CBC engine receiver, which in turn heats the working fluid media to as much as 1600F, pending the ratio of solar dish to receiver areas. A specific gas mixture of xenon/helium, with excellent thermodynamic properties is used for the high temperature application. Turbomachinery in the CBC engine has one moving part / assembly (compressor impeller, alternator rotor and turbine rotor), mounted on compliant foil bearings. Reference figure 4 as an example. The engine operates with a compressor impeller stage pressure ratio 1.6, and is recuperated. Electric power, measured at the CBC engine electric power lugs, is 6.4kW. The CBC engine is not new, (a closed Brayton cycle, sealed to atmosphere) [1], [4], [8], [18], [19]. However, the application to extract thermal energy from the sunlight and provide electric power in commercial and residential use is (patented). In addition, to increase the efficiency of solar energy conversion to electric power, waste heat from the CBC engine provides thermal energy to an ORC engine, to generate an additional electrical output of 3.7kW (measured at the output electric power lugs). With use of an ORC system, the size of the radiator (CBC unit) for heat rejection is reduced significantly. Working fluid HFC-RC245fa [10] was selected for the ORC unit, based on the low temperature application. Also, as with the CBC turbomachinery, the ORC rotor assembly has one moving part, comprised of a pump impeller, alternator rotor and turbine rotor. With the two engines combined, total system thermal efficiency is 48% (10.1kW electric power out / 21kW solar energy in). However, power electronics are needed for conversion of high frequency voltage at the engine output electric power leads to 60/50 Hz power, for customer use. Power electronics losses for this machine, debits the power 0.5 kW. Thus total electric power to the customer, as measured at power electronics output terminals, is 9.6kW. With solar energy, from the reflective sunlight solar dish 21kW and measured output power from the power electronics 9.6kW, the conversion of solar energy to useful electric power an efficiency 46% (i.e. 9.6kW / 21kW). In addition, the design does not require external water / liquid for cooling.


2007 ◽  
Vol 22 (2) ◽  
pp. 392-398 ◽  
Author(s):  
Jian Yin ◽  
Zhenxian Liang ◽  
Jacobus Daniel van Wyk

Sign in / Sign up

Export Citation Format

Share Document