Micro Textured Cutting Inserts with Solid Lubrication as Alternative Coolant to Mineral Oil-Based Cutting Fluid in Turning Operation

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
C. Divya ◽  
L. Suvarna Raju ◽  
B. Singaravel
Keyword(s):  
Process Parameters ◽  
Orthogonal Array ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Solid Lubricants ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Turning Process ◽  
Optimization Of Process Parameters ◽  
Cutting Inserts

Turning process is a primary process in engineering industries and optimization of process parameters enhance the machining performance. Inconel 718 is a nickel-based superalloy, widely found applications in the manufacturing of blades, sheets and discs in aircraft engines and rocket engines. It provides toughness at low temperature, with stand high mechanical stresses at elevated temperature and creep resistance. In this work, turning process is carried out on Inconel 718 with micro whole textured cutting inserts filled with solid lubricants. Three different solid lubricants are used namely molybdenum-di-sulfide (MoS2), tungsten-di-sulfide (WS2) and calcium-di-fluoride (CaF2). Experiments are performed as per L9 orthogonal array. Statistical approaches such as orthogonal array, Signal-to-Noise (S/N) ratio and Analysis of Variance (ANOVA) are used to find the importance and effects of machining parameters. In this study, input parameters included are feed, cutting speed and depth of cut and output parameter includes surface roughness. Optimization of process parameters is carried out and the significance is estimated. The result suggested that WS2 followed by MoS2 and CaF2 given good surface finish value. Also, solid lubricant in machining enhances the sustainability in manufacturing.

scholarly journals Experimental Investigation and Optimization of Machining Parameters in Turning of Aluminum Alloy 075-T651

2021 ◽  
Vol 27 (4) ◽  
pp. 296-305
Author(s):  
Arpit Srivastava ◽  
Mukesh Kumar Verma ◽  
Ramendra Singh Niranjan ◽  
Abhishek Chandra ◽  
Praveen Bhai Patel
Keyword(s):  
Aluminum Alloy ◽  
Process Parameters ◽  
Cutting Speed ◽  
Radial Force ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Optimization Of Process Parameters ◽  
Feed Force ◽  
Aluminum 7075 ◽  
Aluminum Alloy 7075

Abstract Aluminum alloy 7075-T651 is a widely used material in the aviation, marine, and automobile sectors. The wide application marks the importance of this material’s research in the manufacturing field. This research focuses on optimizing input process parameters of the turning process in the machining of Aluminum 7075-T651 with a tungsten carbide insert. The input machining parameters are cutting speed, feed, and depth of cut for the output response parameters cutting force, feed force, radial force, material removal, and surface roughness of the workpiece. For optimization of process parameters, the Taguchi method, with standard L9 orthogonal array, is used. ANOVA is applied to obtain signifi-cant factors and optimal combinations of process parameters.

Machining characteristics of Inconel 718 under several cutting conditions based on Taguchi method

2012 ◽  
Vol 227 (9) ◽  
pp. 1889-1897 ◽  
Author(s):  
R Thirumalai ◽  
JS Senthilkumaar ◽  
P Selvarani ◽  
S Ramesh
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
Flank Wear ◽  
Optimization Technique ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Machining Parameters ◽  
Dry Machining ◽  
Noise Factors

Extensive researchers have conducted several experiments in the past for selecting the optimum parameters in machining nickel based alloy – Inconel 718. These experiments conducted so far are dealt with dry machining and flooded coolant machining of nickel alloy Inconel 718. In this research study, the usage of refrigerated coolant is also dealt with and it is compared with dry machining and flooded coolant machining. Cutting speed, feed and depth of cut are considered as the machining parameters. The effectiveness of the refrigerated coolant in machining the heat resistant super alloy material Inconel 718 with respect to these machining parameters are described in this article. The machinability studies parameters were generated with surface roughness and flank wear. The performance of uncoated carbide cutting tool was investigated at various cutting condition under dry, flooded coolant and refrigerated coolant machining. The relationship between the machining parameters and the performance measures were established and using analysis of variance significant machining parameters determined. This article made an attempt to Taguchi optimization technique to study the machinability performances of Inconel 718. Taguchi approach is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer experiments than a factorial design. Taguchi’s optimization analysis indicates that the factors level, its significance to influence the surface roughness and flank wear for the machining processes. Confirmation tests were conducted at an optimal condition to make a comparison between the experimental results foreseen from the mentioned correlations.

scholarly journals A Combined Experimental and Optimization Model to Improve the Machinability of Nimonic C-263 Superalloy

2020 ◽  
Author(s):  
Prashant Jadhav ◽  
Chinmaya Prasad Mohanty
Keyword(s):  
Process Parameters ◽  
Cutting Speed ◽  
Sem Analysis ◽  
Depth Of Cut ◽  
Process Conditions ◽  
Optimization Of Process Parameters ◽  
Excellent Mechanical Property ◽  
Single Response ◽  
Optimal Set ◽  
Super Alloy

Nickel based superalloys finds extensive usage in manufacturing of intricate part shapes in gas turbine, aircraft, submarine, and chemical industries owing their excellent mechanical property and heat resistant abilities. However, machining of such difficult-to-machine alloys up to the desired accuracy and preciseness is a complex task owing to a rapid tool wear and failure. In view of this, present work proposes an experimental investigation and optimization of process parameters of the cryogenic assisted turning process during machining of Nimonic C-263 super alloy with a multilayer CVD insert. Taguchi’s L-27 orthogonal array is used plan the experiments. Effect of input parameters viz. cutting speed (N), cutting feed (f), depth of cut (d) are studied on responses viz. surface roughness (SR), nose wear (NW) and cutting forces (F) under hybrid cryogenic (direct+indirect) machining environment. A scanning electron microscope (SEM) analysis is carried out to explore the post-machining outcomes on the performance measures. The multiple responses are converted in to single response and ranked according to Taguchi based gray relational grade (TGRG). Feed rate (f) is found to be the most influential parameter from the analysis of variance of GRG. The means of GRG for each level of process parameters are used to improve the optimal process parameters further. Finally, the confirmative experiment is performed with these optimal set of process parameters which showed an improvement of 9.34% in the value of GRG. The proposed work can be beneficial to choose ideal process conditions to enhance the performance of turning operation.

scholarly journals Optimization of CNC Turning Parameters in Machining EN19 using Face Centered Central Composite Design Based RSM

2020 ◽  
Vol 9 (2) ◽  
pp. 889-896
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Removal Rate ◽  
Cutting Speed ◽  
Vital Role ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Cnc Turning ◽  
Software Analysis ◽  
Central Composite

Manufacturing a defect free (quality) product is playing a vital role in today’s globally competitive, customer oriented era. Meeting the demand of the market by producing sufficient quantity is another challenge. Achieving greater production rates without compromising on quality, increases the complexity of the task. Adopting modern manufacturing methods like CNC turning are essential to meet the above requirements. EN19 is an important member in the family of alloy steels, which has a wide variety of applications in automobile and machine tool industries. Optimization of machining parameters is crucial in obtaining the required outputs such as quality and productivity. In this work, optimization of CNC turning parameters for machining EN19 alloy steel is performed. The number of experiments was designed using face centred central composite based response surface methodology with varied independent process parameters namely cutting speed, feed and depth of cut. After designing the experiments, the performance measures such as surface roughness of the test samples and Material Removal Rate (MRR) is calculated using the existing formulae. The influence of parameters on MRR and surface roughness are determined by analysis of variance (ANOVA) and for significance interactions of the process parameters are also considered. Using MINITAB 17 software analysis is performed. Further, regression analysis has been done and second order mathematical model is obtained. Using desirability approach, optimization is carried out.

Cutting forces analysis of micro-milling process on Inconel 718 – a finite element approach

2020 ◽  
Vol 11 (02) ◽  
pp. 2050011
Author(s):  
Padmaja Tripathy ◽  
Kalipada Maity
Keyword(s):  
Finite Element ◽  
Cutting Forces ◽  
Inconel 718 ◽  
Cutting Speed ◽  
Fem Analysis ◽  
Milling Process ◽  
Machining Process ◽  
Micro Milling ◽  
Depth Of Cut ◽  
Machining Parameters

This paper presents a modeling and simulation of micro-milling process with finite element modeling (FEM) analysis to predict cutting forces. The micro-milling of Inconel 718 is conducted using high-speed steel (HSS) micro-end mill cutter of 1mm diameter. The machining parameters considered for simulation are feed rate, cutting speed and depth of cut which are varied at three levels. The FEM analysis of machining process is divided into three parts, i.e., pre-processer, simulation and post-processor. In pre-processor, the input data are provided for simulation. The machining process is further simulated with the pre-processor data. For data extraction and viewing the simulated results, post-processor is used. A set of experiments are conducted for validation of simulated process. The simulated and experimental results are compared and the results are found to be having a good agreement.

Optimizing Feed Force in Turning Process Using Taguchi’s Parameter Design Approach

2014 ◽  
Vol 592-594 ◽  
pp. 668-672
Author(s):  
Praveen Kumar ◽  
Hari Singh
Keyword(s):  
Process Parameters ◽  
Feed Rate ◽  
Cutting Speed ◽  
Design Approach ◽  
Parameter Design ◽  
Depth Of Cut ◽  
Turning Process ◽  
Feed Force ◽  
Optimal Value ◽  
Optimal Setting

The objective of the paper is to obtain an optimal setting of turning process parameters (cutting speed, depth of cut and feed rate) resulting in an optimal value of the feed force when machining En19 steel with tungsten carbide cutting tool inserts. The effects of the selected turning process parameters on feed force and the subsequent optimal settings of the parameters have been accomplished using Taguchi’s parameter design approach. It was indicated by the results that the selected turning process parameters significantly affect the selected machining characteristic. The percent contributions of parameters as quantified in the S/N ANOVA envisage that the relative power of cutting speed (72.09 %) in controlling variation and mean feed force is significantly higher than that of the depth of cut (22.30 %) and feed rate (05.31 %). The predicted optimum feed force is 98.067 N. The results have been validated by the confirmation experiments.

Relationship Between Measurement of Cutting Force and Sensor Location in Turning Process

2012 ◽  
Vol 59 (2) ◽  
Author(s):  
Jaharah A. Ghani ◽  
Poh Siang Jye ◽  
Che Hassan Che Haron ◽  
Muhammad Rizal ◽  
Mohd Zaki Nuawi
Keyword(s):  
Cutting Force ◽  
Strain Gauge ◽  
Cutting Speed ◽  
Strain Gauges ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Sensor Location ◽  
Turning Process ◽  
Feed Force ◽  
Cutting Point

Turning process is widely used in the production of components for automotive and aerospace applications. The machinability of a work material is commonly assessed in terms of cutting tool life, surface finish, and cutting force. These responses are dependent on machining parameters such as cutting speed, feed rate, and depth of cut. In this study, the relationships between cutting force, cutting speed, and sensor location in the turning process were investigated. Strain gauge was chosen as the sensor for the detection of cutting force signal during turning of hardened plain carbon steel JIS S45C. Two strain gauges were mounted on a tool holder at a defined location of I, II, or III at a distance of 37, 42, or 47 mm, respectively, from the cutting point. Only one set of machining experiments was conducted at spindle speed = 1000 rpm, feed = 0.25 mm/rev, and depth of cut = 0.80 mm. The turning process was stopped and the insert was discarded when average flank wear reached 0.30 mm. The main cutting force and the feed force for each cycle measured by the strain gauges at location I, II, and III were collected and analyzed. Results show that when cutting speed was increased, the main cutting force and the feed force were decreased accordingly. The change of was inversely proportional to the change of cutting speed, but the did not decrease continuously and behaved contrarily. A strain gauge placed at a distance of approximately 43 mm from the cutting point was found to be the best and most suitable for sensing accurate force signals.

Characteristics of dimple structure on aluminium silicon alloy fabricated using turning machine

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Faarih Farhan Mohd Nasir ◽  
Jaharah A. Ghani ◽  
Mohd Shahir Kasim ◽  
Wan Fathul Hakim W. Zamri
Keyword(s):  
Cutting Speed ◽  
Area Ratio ◽  
Depth Of Cut ◽  
Textured Surface ◽  
Machining Parameters ◽  
Turning Process ◽  
Content Type ◽  
Silicon Alloy ◽  
Aspect Ratios ◽  
Carbide Insert

Purpose This research aims to present the characteristics of dimple structure which was fabricated using a turning machine, where the characteristics include sizes, shapes, area ratio and aspect ratio. This research aims at filling the gap in the machining parameters of previous research in producing dimple by using turning process with the aid of dynamic assisted tooling for turning (DATT). In producing dimple, a carbide insert grade H1 was used on a hypereutectic aluminium silicon alloy (A390) material. Dimple has many advantages such as for reducing friction coefficient, load-carrying capacity and trap wear debris for sliding mechanical components. Design/methodology/approach There are seven machining parameters (cutting speed, feed rate, depth of cut, frequency, amplitude, rake angle, relief angle and nose radius) which have an influence on dimple produced. Taguchi method (orthogonal arrays L8) was used to conduct the experiment systematically and efficiently for these seven parameters. A carbide insert grade H1 was used as a cutting tool on a turning machine with the aid of DATT. The dimple structure was fabricated on a cylindrical rod hypereutectic aluminium silicon alloy (A390). A profilometer 3D Alicona infinite focus and an optical microscope equipped with Vis software were used to analyse the fabricated dimple structure. Findings Various shapes and sizes of ellipse dimples were produced in this research, including short and long drops with lengths in the range of 517.03–3,927.61 µm, widths of 565.15–1,039.19 µm, depths of 14.46–124.87 µm, area ratios of 5.05–25.65% and aspect ratios of 0.007%–0.111%. There were four experiments within the optimal area ratio range of 10%–20%, i.e. the second, third, seventh and eighth experiments. The width of these dimples was 895.95, 961.39, 787.27 and 829.22 µm, length was 826.26, 3163.13, 885.98 and 1026.65 µm, depth was 83.67, 84.19, 87.05 and 110.70 µm and area ratio was 15.12%, 13.14%, 14.79% and 12.70%. The surface roughness of textured surface was below 1 µm. In this research, the results obtained were similar with that of previous researchers on dimple structure related to tribology performance. Originality/value There exists machining parameters, namely, cutting speed and frequency, that were not used by previous research in producing dimple. These machining parameters (cutting speed and frequency) were used in this research to produce dimple via turning process with the aid of DATT using carbide insert grade H1. The turning process is an environmentally friendly process which is suitable for mass production for fabricating dimple structure as compared to most of the current methods which are widely used in fabricating dimple structure.

Investigation on Laser Assisted Micro Ball Milling of Inconel 718

2014 ◽  
Vol 660 ◽  
pp. 79-83 ◽  
Author(s):  
E.A. Rahim ◽  
N.M. Warap ◽  
Zazuli Mohid ◽  
R. Ibrahim
Keyword(s):  
Inconel 718 ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Processing Parameters ◽  
Micro Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
New Techniques ◽  
Milling Parameters ◽  
Super Alloy

Micro milling of super alloy materials such as nickel based alloys is challenging due to the excellent of its mechanical properties. Therefore, new techniques have been suggested to enhance the machinability of nickel based alloys by pre-heating the workpiece’s surface to reduce its strength. Determining the processing parameters and their effects to the processing characteristics are crucially important. However, not only the micro-milling parameters need to be considered, but the pre-heating parameters are also need to take into consideration as well. These parameters are expected to improve the machinability. In this study, the experiment of LAMM in Inconel 718 was conducted with considering laser power, cutting speed, depth of cut, feed rate and laser-to-cutting tool distance. From the result, the effectiveness of laser assisted and cutting parameter in term of cutting force and tool wear was identified by comparing between conventional and LAMM. Finally, the optimum range of machining parameters can be determined.

Optimisation of Machining Parameters for High Feed End Milling on Inconel 718 Super Alloy

2014 ◽  
Vol 592-594 ◽  
pp. 584-590 ◽  
Author(s):  
Vinay Varghese ◽  
K. Annamalai ◽  
K. Santhosh Kumar
Keyword(s):  
Inconel 718 ◽  
End Milling ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Milling Operation ◽  
High Feed ◽  
Grey Relational ◽  
Super Alloy

This study investigates about machining practices used worldwide for machining of Inconel 718 super alloy. The effect of machining parameters like cutting speed, feed and depth of cut on machining responses like surface roughness and material removal rate when end milling Inconel 718 is studied using nine trials carried out based on L9 orthogonal array. A Taguchi based grey relational analysis was used for optimisation of machining parameters for high feed end milling operation on Inconel 718. An analysis of variance (ANOVA) was used to find the most significant factor. Validation of results through confirmation tests was performed and experimental results show that surface quality and productivity can be improved efficiently with this approach.

Sign in / Sign up

Export Citation Format

Share Document