scholarly journals Paraquat dichloride adsorption from aqueous solution using Carbonized Bambara Groundnut (Vigna subterranean) Shells

2020 ◽  
Vol 12 (1) ◽  
pp. 167-177
Author(s):  
Ayuba Abdullahi Muhammad ◽  
Nyijime Thomas Aondofa
Keyword(s):  
Aqueous Solution ◽  
Water Treatment ◽  
Contact Time ◽  
Adsorption Process ◽  
Bambara Groundnut ◽  
Experimental Result ◽  
Isotherm Model ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Adsorbent Dosage

Carbonized Bambara GroundNut Shell (CBGNS) was used as adsorbent for the adsorption of paraquat dichloride (PQ) from aqueous solution. The prepared adsorbent was characterized using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy methods. Several parameters that might affect the adsorption process including pH, contact time, adsorbent dosage, temperature and initial concentration were investigated and optimized using batch adsorption technique. Results of the study revealed that maximum removal efficiency (98%) was achieved using 0.05g adsorbent dosage, solution pH of 5 and 60 min of contact time. The equilibrium experimental result revealed that Langmuir model best described the adsorption process with R2 value of 0.956.The heat of adsorption process was estimated from Temkin Isotherm model to be 19.99J/mol and the mean free energy was estimated from Duninin-Radushkevich (DRK) isotherm model to be 0.289KJ/mol indicating chemisorptions process. The kinetic and thermodynamic studies revealed that the adsorption processes followed pseudo-second-order kinetics with R2 value of 0.999 and the value of ∆G (- 27.74 kJ mol-1), ∆H (13.145 kJ mol-1) indicate the spontaneous and endothermic nature of PQ adsorption on CBGNS. The results suggested that CBGNS had the potential to become a promising material for PQ contaminated water treatment. Keywords: Adsorption, Paraquat dichloride, Carbonized Bambara Ground nut shell, Water treatment.

scholarly journals Orange Peel As Low-Cost Adsorbent In The Elimination Of Cd(Ii) Ions: Kinetics, Isotherm, Thermodynamic And Optimization Evaluations

2020 ◽  
Author(s):  
Fola Temilade Akinhanmi ◽  
Edwin Andrew Ofudje ◽  
Idowu Abideen Adeogun ◽  
Aina Peter ◽  
Joseph Mayowa Ilo
Keyword(s):  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Orange Peel ◽  
Polluted Water ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Human Beings ◽  
Solution Ph ◽  
Adsorbent Dosage

Abstract The presence of heavy metals in polluted water is known not only to cause stern harm to marine organisms but also to terrestrial plants and animals including human beings. This research applied low-cost and environmental benign adsorbent primed from waste orange peel (OP) for the removal of Cd(II) ions from aqueous solution via batch adsorption process. The surface properties of the orange peel powder were studied using Scanning Electron Microscopy (SEM), X-ray spectroscopy (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). Operational conditions like temperature, contact time, sorbent dosage, solution pH and initial adsorbate concentration were investigated. The utmost uptake of Cd(II) ion was obtained at a contact time of 120 mins, initial metal concentration of 240 mg/L, adsorbent dosage of 0.04 g/L, temperature of 45 °C and solution pH of 5.5. Equilibrium results showed that the orange peel adsorbent has an adsorption capacity of 128.23 mg/g as obtained from the Langmuir isotherm. The adsorption kinetics data followed a pseudo-first-order kinetic model with correlation coefficient (R2) >0.9 and low standard % error values. The adsorption process was found to be endothermic in nature with enthalpy of 0.0046 kJ mol−1 and entropy of-636.865 Jmol-1K-1 respectively. Results from the optimization study indicated that higher adsorbent dosage and lower Cd(II) ion concentration increased the percentage of Cd (II) ion removal. Thus, orange peel could be used in the removal of Cd(II) ion from aqueous solutions.

Zinc removal from aqueous solution using novel adsorbent MISCBA

2016 ◽  
Vol 6 (3) ◽  
pp. 377-388 ◽  
Author(s):  
Ibrahim Umar Salihi ◽  
Shamsul Rahman Muhamed Kutty ◽  
Muhamed Hasnain Isa ◽  
Nasir Aminu
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Metal Ions ◽  
Contact Time ◽  
Adsorption Process ◽  
Negative Impact ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Adsorbent Dosage ◽  
Zinc Removal

Pollution caused by heavy metals has become a serious problem to the environment nowadays. The treatment of wastewater containing heavy metals continues to receive attention because of their toxicity and negative impact on the environment. Recently, various types of adsorbents have been prepared for the uptake of heavy metals from wastewater through the batch adsorption technique. This study focused on the removal of zinc from aqueous solution using microwave incinerated sugarcane bagasse ash (MISCBA). MISCBA was produced using microwave technology. The influence of some parameters such as pH, contact time, initial metal concentration and adsorbent dosage on the removal of zinc was investigated. The competition between H+ and metal ions has affected zinc removal at a low pH value. Optimum conditions for zinc removal were achieved at pH 6.0, contact time 180 min and adsorbent dosage of 10 g/L, respectively. The maximum adsorption capacity for the removal of zinc was found to be 28.6 mg/g. The adsorption process occurred in a multilayered surface of the MISCBA. Chemical reaction was the potential mechanism that regulates the adsorption process. MISCBA can be used as an effective and cheap adsorbent for treatment of wastewater containing zinc metal ions.

scholarly journals Experimental and computational studies on activated Bambara groundnut (Vigna subterranean) hulls for the adsorptive removal of herbicides from aqueous solution

2021 ◽  
Vol 45 (1) ◽  
Author(s):  
Thomas Aondofa Nyijime ◽  
Abdullahi Muhammad Ayuba ◽  
Habibat Faith Chahul
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Quantum Chemical ◽  
Contact Time ◽  
Adsorption Process ◽  
Bambara Groundnut ◽  
Batch Adsorption ◽  
Computational Studies ◽  
Initial Concentration ◽  
Equilibrium Data

Abstract Background The excessive usage of herbicides to control herbs by farmers has become an issue of interest to the environmentalist due to the threat posed by such act to the ecosystem, and therefore, there is the need to curb such practices. The efficiency of Bambara groundnut shell for the removal of pendimethalin (PE) and paraquat dichloride (PQ) herbicides from aqueous solution was established in this work. The activated carbon was prepared via chemical activation method using trioxonitrate (v) acid by determining its void volume, moisture content, bulk density and Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) methods. Batch adsorption techniques were set to optimize the adsorption parameters such as solution pH, adsorbate concentration, contact time, adsorbent dosage and temperature in order to depict the best optimal conditions for the adsorption process. The adsorption process was examined in terms of its equilibrium data, kinetics, thermodynamics involved in the adsorption process as well as computational quantum chemical parameters evaluation. Results The batch adsorption experiments revealed that the amounts of PE and PQ adsorbed were found to vary with the contact time, adsorbent dosage, pH and initial concentration. The adsorption of PE and PQ decreased with increasing adsorbent dose but increases with increasing initial concentration of the PE and PQ solution. Isotherm studies revealed that the equilibrium data fitted to both Langmuir and Freundlich model with R-squared values of 0.976, 0.993 and 0.909, 0.978 for PE and PQ, respectively, which implied that Langmuir isotherm had a better fit. This was also found to be an indication that the uptake of PE and PQ by ACBGNS occurred through monolayer adsorption on identical homogenous sites. Also, kinetic modeling results obtained showed that the pseudo-second-order model explained the adsorption kinetics of PE and PQ by ACBGNS best, which meant that chemisorption was the slowest step and, thus, the rate determining step. The positive value of ΔH and the positive value of ΔG show the endothermic and spontaneous nature of adsorption of PE and PQ ACBGNS. Conclusion Batch adsorption experiment and characterization of the ACBGNS have indicated that Bambara ground nut shell can be used to produce activated carbon that can be applied effectively for adsorption of PE and PQ from an aqueous solution. Computational studies results obtained from quantum chemical analysis are consistent with the experimental results obtained from this study.

scholarly journals Phenol removal from aqueous solution using silica and activated carbon derived from rice husk

2019 ◽  
Vol 14 (4) ◽  
pp. 897-907 ◽  
Author(s):  
Hosseinali Asgharnia ◽  
Hamidreza Nasehinia ◽  
Roohollah Rostami ◽  
Marziah Rahmani ◽  
Seyed Mahmoud Mehdinia
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Water Treatment ◽  
Organic Pollutants ◽  
Rice Husk ◽  
Contact Time ◽  
Adsorption Process ◽  
Phenol Removal ◽  
Initial Concentration ◽  
Maximum Removal

Abstract Phenol and its derivatives are organic pollutants with dangerous effects, such as poisoning, carcinogenicity, mutagenicity, and teratogenicity in humans and other organisms. In this study, the removal of phenol from aqueous solution by adsorption on silica and activated carbon of rice husk was investigated. In this regard, the effects of initial concentration of phenol, pH, dosage of the adsorbents, and contact time on the adsorption of phenol were investigated. The results showed that the maximum removal of phenol by rice husk silica (RHS) and rice husk activated carbon (RHAC) in the initial concentration of 1 mgL−1 phenol, 2 gL−1 adsorbent mass, 120 min contact time, and pH 5 (RHS) or pH 6 (RHAC) were obtained up to 91% and 97.88%, respectively. A significant correlation was also detected between increasing contact times and phenol removal for both adsorbents (p < 0.01). The adsorption process for both of the adsorbents was also more compatible with the Langmuir isotherm. The results of this study showed that RHS and RHAC can be considered as natural and inexpensive adsorbents for water treatment.

scholarly journals Response surface methodology for optimization of Cd(II) adsorption from wastewaters by fabricated tartaric acid-maize tassel magnetic hybrid sorbent

2019 ◽  
Vol 9 (4) ◽  
pp. 3996-4005 ◽  
Keyword(s):  
Tartaric Acid ◽  
Contact Time ◽  
Adsorption Process ◽  
Desirability Function ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Biomass Waste ◽  
Hybrid Sorbent ◽  
Maize Tassel

Maize tassels (MT), an agro-based biomass waste was carbonised followed by thermo-chemical modification using tartaric acid. The functionalized activated carbon was further modified to yield a magnetic hybrid composite adsorbent. The adsorbent was characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The adsorbent was evaluated for its efficiency to remove Cd(II) ions from aqueous solutions through batch adsorption studies following a Central Composite Design. Effects of solution pH, contact time, adsorbent dosage, initial metal concentration and temperature on Cd(II) adsorption were investigated. Optimization of the adsorption process was done using desirability function on the Design Expert V11 software. The desirability function showed that the optimum parameters were pH 5.29, contact time (67.50 min), dosage (0.575 g) and initial concentration (152.50 mg/L). The adsorption process was analysed using kinetic and isotherm models. The kinetics of the adsorption process followed the pseudo-second-order model (lowest sum of square error (SSE) values and correlation coefficients (R2) > 0.999) in addition to the intraparticle diffusion model. The isotherm data were consistent with the Langmuir isotherm as evidenced by the highest correlation coefficient (R2= 0.998). The thermodynamic parameters showed that the process was endothermic and spontaneous in nature. The adsorption capacity of the adsorbent was found to be 188.68 mg/g at 20 ⁰C which is higher than that of the previously reported magnetic maize tassel hybrid (52.05 mg/g). The adsorbent showed good removal efficiency on real effluent samples.

scholarly journals Methylene Blue Adsorption from aqueous solution by low cost vine-wood biomass

2021 ◽  
Author(s):  
Rachida Souidi ◽  
yasmina khane ◽  
Lahcen Belarbi ◽  
Smain Bousalem
Keyword(s):  
Methylene Blue ◽  
Sulfuric Acid ◽  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Sulfuric Acid Concentration ◽  
Analytical Techniques ◽  
Batch Adsorption ◽  
Adsorbent Dosage ◽  
Adsorption Desorption

Abstract In this work, the sawdust of vine wood (VW) was treated with sulfuric acid and used to adsorb methylene blue (MB) from aqueous solutions via a batch adsorption process. The characteristics of the adsorbent were determined by various analytical techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM) and Brunauer−Emmett−Teller (BET) N2 adsorption−desorption isotherms. The effects of various experimental parameters including sulfuric acid concentration, particle size of the adsorbent, pH of the solution, contact time, initial concentration, adsorbent dosage and temperature on adsorption of MB by activating sawdust were systematically investigated. The experimental results showed that the adsorption efficiency was increased with contact time and adsorbent dosage. The maximum removal efficiency was found after 180 min of solid/liquid contact with adsorbent doses of 1 g/l for sawdust. The isotherm and kinetic experimental data for MB adsorption on VW sawdust were best-fitted by Langmuir models and Pseudo-second-order, respectively. The calculated values of the entropy (ΔS°), enthalpy (ΔH°) and Gibbs energy (ΔG°) indicated that the adsorption process was exothermic in nature. These results suggest that the activated sawdust can be employed as a low-cost and environmentally friendly adsorbent for the treatment of wastewaters containing dyes.

scholarly journals Continuous Phenol Removal Using a Liquid–Solid Circulating Fluidized Bed

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3839
Author(s):  
Nandhini Sureshkumar ◽  
Samiha Bhat ◽  
Shwetha Srinivasan ◽  
Nirmala Gnanasundaram ◽  
Murugesan Thanapalan ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Fluidized Bed ◽  
Contact Time ◽  
Circulating Fluidized Bed ◽  
Glass Beads ◽  
Batch Adsorption ◽  
Phenol Removal ◽  
Solution Ph ◽  
Adsorbent Dosage ◽  
Adsorbent Regeneration

A liquid-solid circulating fluidized bed (LSCFB) helps to overcome the shortcomings of conventional fluidized beds by using a particle separation and return system as an integral part of the overall reactor configuration. Batch adsorption experiments were carried out for the removal of phenol from a synthetically prepared solution using fresh activated-carbon-coated glass beads. The morphological features and surface chemistry of the adsorbent were analyzed via SEM and FTIR techniques. The adsorbent dosage, contact time and temperature were varied along with solution pH to assess their effects on the adsorbent performance for phenol removal. Isotherm modeling showed that the phenol removal using the activated-carbon glass beads followed the Langmuir model. Effectively, it was observed at an adsorbent loading of 2.5 g/150 mL of feed volume and a contact time of 3 h produced an 80% efficiency in the batch study. Furthermore, on scaling it up to the column, the desired 98% phenol-removal efficiency was obtained with an adsorbent dosage of 250 g and contact time of 25 min. Adsorbent regeneration using 5% (v/v) ethanol showed a 64% desorption of phenol from the sorbent within 20 min in the LSCFB.

Removal of Fluoride on Chitosan Coated Alumina (CAL) from Aqueous Solution

2012 ◽  
Vol 518-523 ◽  
pp. 797-800 ◽  
Author(s):  
Xuan Lin Tang ◽  
Huan Zhen Zhang ◽  
Shuang Zhao ◽  
Shu Fen Gong
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Rate ◽  
Fluoride Removal ◽  
Batch Experiments ◽  
Solution Ph ◽  
Initial Concentration ◽  
Adsorbent Dosage ◽  
Naoh Solution

CAL beads were made by dropping wise mixture of chitosan and alumina into NaOH solution. Effects of contact time, adsorbent dosage, initial concentration and pH on fluoride removal were carried out by batch experiments. Results show that adsorption rate was relatively rapid in the first 6 h, thereafter distinctly decreased until adsorption reached the equilibrium within 48 h, at this time, adsorption capacity was up to 0.67 mg/g, which was much higher than raw chitosan (0.052 mg/g). Fluoride removal increased significantly with an increase of adsorbent dosage, however, it rose slowly when the adsorbent dosage was above 16 g/L. Adsorption capacity reduced from 0.75 mg/g to 0.64mg/g when solution pH rose from 4 to 7, nevertheless, adsorption was relatively independent on solution pH between 7 and 10.

scholarly journals Removal of Methylene Blue Dye From Aqueous Solution Using PDADMAC Modified ZSM-5 Zeolite as a Novel Adsorbent 

2021 ◽  
Author(s):  
Sabarish Radoor ◽  
Jasila Karayil ◽  
Aswathy Jayakumar ◽  
Jyotishkumar Parameswaranpillai ◽  
Suchart Siengchin
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Contact Time ◽  
Adsorption Process ◽  
Nitrogen Adsorption ◽  
Second Order ◽  
Blue Dye ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Pseudo Second Order

Abstract In the present work, we modified ZSM-5 zeolite using a bio polymer poly (diallyl dimethyl ammonium chloride) and employed it for the removal of cationic dye, methylene blue from aqueous solution. The chemical and physical properties of the modified ZSM-5 zeolite were investigated using XRD, FTIR, SEM, TEM, nitrogen adsorption, TGA and 27Al NMR. Modified ZSM-5 zeolite possesses high surface area and pore diameter which was confirmed from SEM, TEM and nitrogen adsorption analysis. Adsorption of methylene blue on zeolite was investigated by batch adsorption technique. The effect of different parameters such as zeolite dosage, initial methylene blue concentration, temperature, pH and contact time on the adsorption process was discussed. Maximum adsorption capacity (4.31 mg/g) was achieved using 0.1g of modified ZSM-5 zeolite at the optimum conditions (initial dye concentration: 10 mg/L, pH: 10, temperature:30oC and contact time: 300 min). The experimental data were fitted into Langmuir and Freundlich models and the results indicate that the adsorption process followed Freundlich isotherm. Kinetic data were investigated using pseudo-first-order and pseudo-second-order models. Kinetic analysis indicates that pseudo-second-order model is more suitable to describe adsorption of MB on modified ZSM-5 zeolite. The reusability test suggests that the adsorbent could be reused at least six times without significant loss in removal efficiency.

scholarly journals Synthesis of Modified Spent Tea for Aspirin Adsorption in Aqueous Solution

2019 ◽  
Vol 8 (3) ◽  
pp. 531-534
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Acid Treatment ◽  
Agricultural Waste ◽  
Point Of Zero Charge ◽  
Solution Temperature ◽  
Batch Adsorption ◽  
Optimal Conditions ◽  
Solution Ph ◽  
Adsorption Mechanisms

This present study focuses on the synthesis of a new modified eco-friendly adsorbent, spent tea (ST, discarded Camellia sinensis leaves), and its application in the adsorption of Aspirin from aqueous solution by batch adsorption technique. This is an effort in shifting towards new substitutes that are both inexpensive and highly efficient, such as agricultural waste materials as an alternative of the commonly used adsorbent material, activated carbon. The ST will first undergo an acid treatment using phosphoric acid, and subsequently modified with Polyethyleneimine (PEI) using Glutaraldehyde (GA) as the cross-linker. Aspirin removal efficiency was compared between the untreated spent tea (ST) and new PEI modified acid treated spent tea (TA-PEI). Effects of ratio of acid treated spent tea (TA) and PEI (1:1, 1:2,1:3, 2:1,3:1), and GA concentration (0,0.5,1.0,2.0,3.0, and 4.0 v/v%) were investigated. The optimal conditions for the synthesis of the modified adsorbent, TA-PEI are TA: PEI ratio of 1:2, and 0.5(v/v %) of GA. Afterwards, the untreated ST and TA-PEI were tested to determine the effect of contact time on Aspirin adsorption. It was found that TA-PEI shows great removal effectiveness - up to 64.70% before reaching equilibrium after 30min of contact time. Nevertheless, ST only shows removal of 1% and after 15min, there is no appreciable adsorption. These results suggested that TA-PEI has high potential to be used as an effective adsorbent for Aspirin removal. In the future, TA-PEI will undergo further research to investigate the effects of different adsorbent dosage, solution pH, initial concentration, solution temperature, and contact time. Several analysis (FTIR, SEM, CHNS, BET and point of zero charge) has to be done as well to get a better understanding of its properties and the adsorption mechanisms

Sign in / Sign up

Export Citation Format

Share Document