Zinc removal from aqueous solution using novel adsorbent MISCBA

2016 ◽  
Vol 6 (3) ◽  
pp. 377-388 ◽  
Author(s):  
Ibrahim Umar Salihi ◽  
Shamsul Rahman Muhamed Kutty ◽  
Muhamed Hasnain Isa ◽  
Nasir Aminu
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Metal Ions ◽  
Contact Time ◽  
Adsorption Process ◽  
Negative Impact ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Adsorbent Dosage ◽  
Zinc Removal

Pollution caused by heavy metals has become a serious problem to the environment nowadays. The treatment of wastewater containing heavy metals continues to receive attention because of their toxicity and negative impact on the environment. Recently, various types of adsorbents have been prepared for the uptake of heavy metals from wastewater through the batch adsorption technique. This study focused on the removal of zinc from aqueous solution using microwave incinerated sugarcane bagasse ash (MISCBA). MISCBA was produced using microwave technology. The influence of some parameters such as pH, contact time, initial metal concentration and adsorbent dosage on the removal of zinc was investigated. The competition between H+ and metal ions has affected zinc removal at a low pH value. Optimum conditions for zinc removal were achieved at pH 6.0, contact time 180 min and adsorbent dosage of 10 g/L, respectively. The maximum adsorption capacity for the removal of zinc was found to be 28.6 mg/g. The adsorption process occurred in a multilayered surface of the MISCBA. Chemical reaction was the potential mechanism that regulates the adsorption process. MISCBA can be used as an effective and cheap adsorbent for treatment of wastewater containing zinc metal ions.

Extraction of Heavy Metals from Aqueous Medium by Husk Biomass: Adsorption Isotherm, Kinetic and Thermodynamic study

2019 ◽  
Vol 233 (2) ◽  
pp. 201-223 ◽  
Author(s):  
Khalida Naseem ◽  
Rahila Huma ◽  
Aiman Shahbaz ◽  
Jawaria Jamal ◽  
Muhammad Zia Ur Rehman ◽  
...  
Keyword(s):  
Metal Ions ◽  
Aqueous Medium ◽  
Contact Time ◽  
Metal Ion ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorbent Dosage ◽  
Adsorption Sites ◽  
Order Kinetic Model

Abstract This study describes the adsorption of Cu (II), Co (II) and Ni (II) ions from wastewater on Vigna radiata husk biomass. The ability of adsorbent to capture the metal ions has been found to be in the order of Ni (II)>Co (II) and Cu (II) depending upon the size and nature of metal ions to be adsorbed. It has been observed that percentage removal of Cu (II), Co (II) and Ni (II) ions increases with increase of adsorbent dosage, contact time and pH of the medium but up to a certain extent. Maximum adsorption capacity (qmax) for Cu (II), Co (II) and Ni (II) ions has been found to be 11.05, 15.04 and 19.88 mg/g, respectively, under optimum conditions of adsorbent dosage, contact time and pH of the medium. Langmuir model best fits the adsorption process with R2 value approaches to unity for all metal ions as compared to other models because adsorption sites are seemed to be equivalent and only monolayer adsorption may occur as a result of binding of metal ion with a functional moiety of adsorbent. Pseudo second order kinetic model best interprets the adsorption process of Cu (II), Co (II) and Ni (II) ions. Thermodynamic parameters such as negative value of Gibbs energy (∆G°) gives information about feasibility and spontaneity of the process. Adsorption process was found to be endothermic for Cu (II) ions while exothermic for Co (II) and Ni (II) ions as signified by the value of enthalpy change (∆H°). Husk biomass was recycled three times for removal of Ni (II) from aqueous medium to investigate its recoverability and reusability. Moreover V. radiata husk biomass has a potential to extract Cu (II) and Ni (II) from electroplating wastewater to overcome the industrial waste water pollution.

scholarly journals Paraquat dichloride adsorption from aqueous solution using Carbonized Bambara Groundnut (Vigna subterranean) Shells

2020 ◽  
Vol 12 (1) ◽  
pp. 167-177
Author(s):  
Ayuba Abdullahi Muhammad ◽  
Nyijime Thomas Aondofa
Keyword(s):  
Aqueous Solution ◽  
Water Treatment ◽  
Contact Time ◽  
Adsorption Process ◽  
Bambara Groundnut ◽  
Experimental Result ◽  
Isotherm Model ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Adsorbent Dosage

Carbonized Bambara GroundNut Shell (CBGNS) was used as adsorbent for the adsorption of paraquat dichloride (PQ) from aqueous solution. The prepared adsorbent was characterized using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy methods. Several parameters that might affect the adsorption process including pH, contact time, adsorbent dosage, temperature and initial concentration were investigated and optimized using batch adsorption technique. Results of the study revealed that maximum removal efficiency (98%) was achieved using 0.05g adsorbent dosage, solution pH of 5 and 60 min of contact time. The equilibrium experimental result revealed that Langmuir model best described the adsorption process with R2 value of 0.956.The heat of adsorption process was estimated from Temkin Isotherm model to be 19.99J/mol and the mean free energy was estimated from Duninin-Radushkevich (DRK) isotherm model to be 0.289KJ/mol indicating chemisorptions process. The kinetic and thermodynamic studies revealed that the adsorption processes followed pseudo-second-order kinetics with R2 value of 0.999 and the value of ∆G (- 27.74 kJ mol-1), ∆H (13.145 kJ mol-1) indicate the spontaneous and endothermic nature of PQ adsorption on CBGNS. The results suggested that CBGNS had the potential to become a promising material for PQ contaminated water treatment. Keywords: Adsorption, Paraquat dichloride, Carbonized Bambara Ground nut shell, Water treatment.

scholarly journals Removal of Methylene Blue Dye From Aqueous Solution Using PDADMAC Modified ZSM-5 Zeolite as a Novel Adsorbent 

2021 ◽  
Author(s):  
Sabarish Radoor ◽  
Jasila Karayil ◽  
Aswathy Jayakumar ◽  
Jyotishkumar Parameswaranpillai ◽  
Suchart Siengchin
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Contact Time ◽  
Adsorption Process ◽  
Nitrogen Adsorption ◽  
Second Order ◽  
Blue Dye ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Pseudo Second Order

Abstract In the present work, we modified ZSM-5 zeolite using a bio polymer poly (diallyl dimethyl ammonium chloride) and employed it for the removal of cationic dye, methylene blue from aqueous solution. The chemical and physical properties of the modified ZSM-5 zeolite were investigated using XRD, FTIR, SEM, TEM, nitrogen adsorption, TGA and 27Al NMR. Modified ZSM-5 zeolite possesses high surface area and pore diameter which was confirmed from SEM, TEM and nitrogen adsorption analysis. Adsorption of methylene blue on zeolite was investigated by batch adsorption technique. The effect of different parameters such as zeolite dosage, initial methylene blue concentration, temperature, pH and contact time on the adsorption process was discussed. Maximum adsorption capacity (4.31 mg/g) was achieved using 0.1g of modified ZSM-5 zeolite at the optimum conditions (initial dye concentration: 10 mg/L, pH: 10, temperature:30oC and contact time: 300 min). The experimental data were fitted into Langmuir and Freundlich models and the results indicate that the adsorption process followed Freundlich isotherm. Kinetic data were investigated using pseudo-first-order and pseudo-second-order models. Kinetic analysis indicates that pseudo-second-order model is more suitable to describe adsorption of MB on modified ZSM-5 zeolite. The reusability test suggests that the adsorbent could be reused at least six times without significant loss in removal efficiency.

scholarly journals Removal of Heavy Metals from Textile Wastewater Using Sugarcane Bagasse Activated Carbon

2018 ◽  
Vol 7 (4.30) ◽  
pp. 112 ◽  
Author(s):  
Mohd Adib Mohammad Razi ◽  
Adel Al- Gheethi ◽  
Izzatul Ashikin ZA
Keyword(s):  
Heavy Metals ◽  
Activated Carbon ◽  
Metal Ions ◽  
Sugarcane Bagasse ◽  
Contact Time ◽  
Adsorption Process ◽  
Textile Wastewater ◽  
Attractive Alternative ◽  
Adsorption Efficiency ◽  
Adsorbent Dosage

Excessive release of textile wastewater with heavy metals into environment has posed a great problem to the natural water system. The efficiency of the adsorption process to remove heavy metals depend on the adsorbent. The commercial activated carbon is one of the most efficient adsorbent, but the limitation lies in the high cost. Therefore, the present study aimed to investigate the efficiency of sugarcane bagasse activated carbon modified by phosphoric acid as adsorbent for the removal of zinc (Zn) and Ferum (Fe) from the textile wastewater. The adsorption process was conducted using batch method as a function for pH (2-7), contact time (30 min to 24 h) and adsorbent dosage (0.6 to 6g). The final concentrations of the metal ions were determined by ICP-MS. The results revealed that the adsorption efficiency increased with the contact time, the optimum time was recorded after 2 h. The removal percentage of Zn and Fe associated with the adsorbent dosage due to the greater surface area with optimum value of 4.0 g. The increasing of pH from 2 to 6 correlated with high adsorption efficiency, with the optimum condition at pH 5. The maximum percentage removal of Fe, Zn was 80%. These findings indicated that the SBAC is an attractive alternative adsorbent material for the metal ions removal in textile wastewater.

scholarly journals Utilization of Agro-Waste in the Elimination of Dyes from Aqueous Solution: Equilibrium, Kinetic and Thermodynamic Studies

2021 ◽  
Vol 86 ◽  
pp. 11-23
Author(s):  
Nnaemeka John Okorocha ◽  
Chijioke E. Omaliko ◽  
Collins C. Osuagwu ◽  
Maureen O. Chijioke-Okere ◽  
Conrad K. Enenebeaku
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Adsorption Process ◽  
Dye Adsorption ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Thermodynamic Quantities ◽  
Order Kinetic ◽  
Maize Cob ◽  
Adsorbent Dose

The prospective of maize cob powder (MCP) as an effective adsorbent for the removal of malachite green (MG) and congo red (CR) dyes from aqueous solution was investigated. The presence of functional groups and pores on maize cob powder were confirmed by FTIR and SEM analysis. Batch adsorption studies were conducted and various parameters such as contact time, adsorbent dosage, initial dye concentration, pH and temperature were examined to observe their effects in the dyes adsorption process. The optimum conditions for the adsorption of MG and CR onto the adsorbent (MCP) was found to be: contact time (60mins), pH (10.0) and temperature (303 K), adsorbent dose (1 g) for an initial MG dye concentration of 50 mg/L and contact time (80mins), pH (2.0) and temperature (343 K) for an initial CR dye concentration of 50 mg/L and adsorbent dose 1.0 g respectively. The experimental equilibrium adsorption data fitted best and well to the Freundlich isotherm model for CR dye adsorption and Langmuir Isotherm for MG adsorption. The maximum adsorption capacity was found to be 13.02 mg/g and 9.41 mg/g for the adsorption of MG and CR dyes respectively. The kinetic data conformed to the pseudo-second-order kinetic model. Thermodynamic quantities such as Gibbs free energy (ΔG0), enthalpy (ΔH0) and entropy (ΔS0) were evaluated and the negative values of ΔG0, ΔH0 and ΔS0 obtained indicated the spontaneous and exothermic nature of the MG adsorption process while positive enthalpy (ΔH0) indicated an endothermic nature of CR adsorption process.

Utilisation of Biomass and Hybrid Biochar from Elephant Grass and Low Density Polyethylene for the Competitive Adsorption of Pb(II), Cu(II), Fe(II) and Zn(II) from Aqueous Media

2020 ◽  
Vol 13 ◽  
Author(s):  
Joshua O. Ighalo ◽  
Lois T. Arowoyele ◽  
Samuel Ogunniyi ◽  
Comfort A. Adeyanju ◽  
Folasade M. Oladipo-Emmanuel ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Removal Efficiency ◽  
Contact Time ◽  
Competitive Adsorption ◽  
Adsorption Process ◽  
Aqueous Media ◽  
Polluted Water ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Elephant Grass

Background: The presence of pollutants in polluted water is not singularized hence pollutant species are constantly in competition for active sites during the adsorption process. A key advantage of competitive adsorption studies is that it informs on the adsorbent performance in real water treatment applications. Objective: This study aims to investigate the competitive adsorption of Pb(II), Cu(II), Fe(II) and Zn(II) using elephant grass (Pennisetum purpureum) biochar and hybrid biochar from LDPE. Method: The produced biochar was characterised by Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR). The effect of adsorption parameters, equilibrium isotherm modelling and parametric studies were conducted based on data from the batch adsorption experiments. Results: For both adsorbents, the removal efficiency was >99% over the domain of the entire investigation for dosage and contact time suggesting that they are very efficient for removing multiple heavy metals from aqueous media. It was observed that removal efficiency was optimal at 2 g/l dosage and contact time of 20 minutes for both adsorbent types. The Elovich isotherm and the pseudo-second order kinetic models were best-fit for the competitive adsorption process. Conclusion: The study was able to successfully reveal that biomass biochar from elephant grass and hybrid biochar from LDPE can be used as effective adsorbent material for the removal of heavy metals from aqueous media. This study bears a positive implication for environmental protection and solid waste management.

scholarly journals Batch Sorption Experiments: Langmuir and Freundlich Isotherm Studies for the Adsorption of Textile Metal Ions onto Teff Straw (Eragrostis tef) Agricultural Waste

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Mulu Berhe Desta
Keyword(s):  
Heavy Metals ◽  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Low Cost ◽  
Agricultural Waste ◽  
Equilibrium Concentration ◽  
Eragrostis Tef ◽  
Batch Adsorption ◽  
Textile Effluents

Adsorption of heavy metals (Cr, Cd, Pb, Ni, and Cu) onto Activated Teff Straw (ATS) has been studied using batch-adsorption techniques. This study was carried out to examine the adsorption capacity of the low-cost adsorbent ATS for the removal of heavy metals from textile effluents. The influence of contact time, pH, Temperature, and adsorbent dose on the adsorption process was also studied. Results revealed that adsorption rate initially increased rapidly, and the optimal removal efficiency was reached within about 1 hour. Further increase in contact time did not show significant change in equilibrium concentration; that is, the adsorption phase reached equilibrium. The adsorption isotherms could be fitted well by the Langmuir model. The value in the present investigation was less than one, indicating that the adsorption of the metal ion onto ATS is favorable. After treatment with ATS the levels of heavy metals were observed to decrease by 88% (Ni), 82.9% (Cd), 81.5% (Cu), 74.5% (Cr), and 68.9% (Pb). Results indicate that the freely abundant, locally available, low-cost adsorbent, Teff straw can be treated as economically viable for the removal of metal ions from textile effluents.

scholarly journals Comparative Adsorptive Removal of Selected Heavy Metals from Battery Wastewater by Purified and Polyethylene Glycol Modified Carbon Nanotubes

2021 ◽  
Author(s):  
Abdulkareem AS ◽  
Hamzat WA ◽  
Tijani JO ◽  
Bankole MT ◽  
Titus Egbosiuba ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Carbon Nanotubes ◽  
Polyethylene Glycol ◽  
Toxic Metals ◽  
Contact Time ◽  
Batch Adsorption ◽  
Adsorption Effect ◽  
Adsorbent Dosage ◽  
Modified Carbon Nanotubes ◽  
Nano Adsorbent

Abstract Comparative adsorption study of some toxic metals (Ni, Fe, Cu, Cd, and Pb) from battery industrial effluent by purified and polyethylene glycol-modified carbon nanotubes (CNTs) is reported. The as-prepared CNTs via chemical vapour deposition method (A-CNTs), its acid purified form (P-CNTs), and polyethylene glycol functionalized form (PEG-CNTs) were characterized by HRTEM, BET, HRSEM, FTIR and XRD. The HRSEM and HRTEM micrograph revealed the formation of multi-walled tubular network structures of different inner and outer diameter. The BET study of PEG-CNTs and purified CNTs showed surface areas of 970.81 m2/g and 781.88 m2/g, respectively. The nanomaterials batch adsorption effect of various parameters such as contact time, nano-adsorbent dosage and temperature was conducted. The optimum equilibrium to achieve maximum removal of Cd (83.41 %), Ni (92.79 %), Fe (95.93%), Pb (97.16 %) Cu (99.9 9%) using PEG-CNTs was 90 min of contact time, 0.3 g of nano-adsorbent dosage and 60 oC temperature. While the maximum percentage removal efficiencies accomplished using P-CNTs under the same applied conditions were Cd (78.64 %), Ni (76.12 %), Fe (92.87 %), Pb (90.7 2%) Cu (99.09 %). PEG-CNTs was seen as more effective than P-CNTs. Adsorption data of Ni on P-CNTs followed Langmuir isotherm while the adsorption equilibrium model (Freundlich isotherm) of Ni, Fe, Cu and Pb on PEG-CNTs were fitted well. However, in both cases, the sorption kinetic study followed the pseudo-second-order model. The thermodynamics showed that the removal of toxic metals from battery wastewater was spontaneous and endothermic irrespective of the nano-adsorbents. The study found that surface modification of CNTs by polyethylene glycol adequately improved the nanotubes, thus leading to relatively adsorption capacities of heavy metals from industrial battery effluent.

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

scholarly journals Adsorption of Chromium(VI) and Zinc(II) Ions on the Skin of Orange Peels (Citrus sinensis)

1970 ◽  
Vol 26 ◽  
pp. 31-39 ◽  
Author(s):  
O. A. Ekpete ◽  
F. Kpee ◽  
J. C. Amadi ◽  
R. B. Rotimi
Keyword(s):  
Heavy Metals ◽  
Metal Ions ◽  
Citrus Sinensis ◽  
Contact Time ◽  
Heavy Metal Ions ◽  
Orange Peel ◽  
Maximum Adsorption Capacity ◽  
Orange Peels ◽  
Chromium Vi ◽  
Aas Method

The removal of heavy metal ions Cr (VI) and Zn (II) from aqueous solution using theskin of orange peel (Citrus sinensis) as an adsorbent under different experimentalconditions was investigated in this study. The concentrations of the metal ions adsorbedwere determined by atomic absorption spectroscopic (AAS) method. The parametersinvestigated were temperature, contact time, adsorbent dosage, initial metal ionsconcentration and pH. It was observed that the white inner skin of orange removed more ofCr (VI) than Zn (II) metal ions in all the adsorption experiments. The optimum removal ofthe Cr (VI) and Zn (II) metal ions occurred at pH 3 and at temperature 30°C. Application ofthe Langmuir isotherm to the systems yielded maximum adsorption capacity of 8.068 (mg/g)and 1.078 (mg/g) for Cr (VI) and Zn (II) metal ions respectively.Keywords: Orange peel; Adsorption; Heavy metals; LangmuirDOI: 10.3126/jncs.v26i0.3628Journal of Nepal Chemical SocietyVol. 26, 2010Page:31-39

Sign in / Sign up

Export Citation Format

Share Document