scholarly journals Response surface methodology for optimization of Cd(II) adsorption from wastewaters by fabricated tartaric acid-maize tassel magnetic hybrid sorbent

2019 ◽  
Vol 9 (4) ◽  
pp. 3996-4005 ◽  
Keyword(s):  
Tartaric Acid ◽  
Contact Time ◽  
Adsorption Process ◽  
Desirability Function ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Biomass Waste ◽  
Hybrid Sorbent ◽  
Maize Tassel

Maize tassels (MT), an agro-based biomass waste was carbonised followed by thermo-chemical modification using tartaric acid. The functionalized activated carbon was further modified to yield a magnetic hybrid composite adsorbent. The adsorbent was characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The adsorbent was evaluated for its efficiency to remove Cd(II) ions from aqueous solutions through batch adsorption studies following a Central Composite Design. Effects of solution pH, contact time, adsorbent dosage, initial metal concentration and temperature on Cd(II) adsorption were investigated. Optimization of the adsorption process was done using desirability function on the Design Expert V11 software. The desirability function showed that the optimum parameters were pH 5.29, contact time (67.50 min), dosage (0.575 g) and initial concentration (152.50 mg/L). The adsorption process was analysed using kinetic and isotherm models. The kinetics of the adsorption process followed the pseudo-second-order model (lowest sum of square error (SSE) values and correlation coefficients (R2) > 0.999) in addition to the intraparticle diffusion model. The isotherm data were consistent with the Langmuir isotherm as evidenced by the highest correlation coefficient (R2= 0.998). The thermodynamic parameters showed that the process was endothermic and spontaneous in nature. The adsorption capacity of the adsorbent was found to be 188.68 mg/g at 20 ⁰C which is higher than that of the previously reported magnetic maize tassel hybrid (52.05 mg/g). The adsorbent showed good removal efficiency on real effluent samples.

scholarly journals Paraquat dichloride adsorption from aqueous solution using Carbonized Bambara Groundnut (Vigna subterranean) Shells

2020 ◽  
Vol 12 (1) ◽  
pp. 167-177
Author(s):  
Ayuba Abdullahi Muhammad ◽  
Nyijime Thomas Aondofa
Keyword(s):  
Aqueous Solution ◽  
Water Treatment ◽  
Contact Time ◽  
Adsorption Process ◽  
Bambara Groundnut ◽  
Experimental Result ◽  
Isotherm Model ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Adsorbent Dosage

Carbonized Bambara GroundNut Shell (CBGNS) was used as adsorbent for the adsorption of paraquat dichloride (PQ) from aqueous solution. The prepared adsorbent was characterized using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy methods. Several parameters that might affect the adsorption process including pH, contact time, adsorbent dosage, temperature and initial concentration were investigated and optimized using batch adsorption technique. Results of the study revealed that maximum removal efficiency (98%) was achieved using 0.05g adsorbent dosage, solution pH of 5 and 60 min of contact time. The equilibrium experimental result revealed that Langmuir model best described the adsorption process with R2 value of 0.956.The heat of adsorption process was estimated from Temkin Isotherm model to be 19.99J/mol and the mean free energy was estimated from Duninin-Radushkevich (DRK) isotherm model to be 0.289KJ/mol indicating chemisorptions process. The kinetic and thermodynamic studies revealed that the adsorption processes followed pseudo-second-order kinetics with R2 value of 0.999 and the value of ∆G (- 27.74 kJ mol-1), ∆H (13.145 kJ mol-1) indicate the spontaneous and endothermic nature of PQ adsorption on CBGNS. The results suggested that CBGNS had the potential to become a promising material for PQ contaminated water treatment. Keywords: Adsorption, Paraquat dichloride, Carbonized Bambara Ground nut shell, Water treatment.

scholarly journals Influence of Acid Activation of a Mixture of Illite, Koalinite, and Chlorite Clays on the Adsorption of Methyl Violet 6B Dye

2021 ◽  
pp. 1761-1778
Author(s):  
Saba Adel Saed ◽  
Donia Aidan
Keyword(s):  
Adsorption Process ◽  
Methyl Violet ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Acid Activation ◽  
Solution Ph ◽  
Adsorption Method ◽  
Force Microscopy ◽  
Atomic Force ◽  
Hoff Equation

The influence of acid activation of a mixture of illite, kaolinite, and chlorite clays collected from the area of Zorbatiya (east of Iraq) on the adsorption of methyl violet 6B (MV6B) as a cationic dye was studied. The activation was carried out by using 0.25M HCl and 0.25M . Raw and acid-activated clays were analyzed by atomic force microscopy (AFM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). Batch adsorption method was used to study the adsorption of MV6B onto the raw and acid activated clays. The impacts of different factors on the adsorption process were studied, such as clay weight, agitation time, starting MV6B concentration, temperature, ionic strength, and solution pH. The adsorption process was described by using Langmuir, Freundlich, Temkin, and Dubinin- Radushkevich isotherm models. Thermodynamic parameters like  were estimated based on Vanʼt Hoff equation.

scholarly journals ADSORPTION POTENTIAL FOR A MIXTURE OF CHEMICALLY AND THERMALLY TREATED CLAYS TO REMOVE ORANGE G DYE FROM WASTE-WATER

2021 ◽  
Vol 13 (2) ◽  
pp. 10-31
Author(s):  
Saba A. Saeed1 ◽  
◽  
Dunya E. AL-Mammar2 ◽  
Keyword(s):  
Adsorption Process ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Alkali Activation ◽  
Acid Activation ◽  
Solution Ph ◽  
Adsorption Method ◽  
Orange G ◽  
Hoff Equation ◽  
The Impact

This study examined the adsorption behavior of anionic dye (orange G) from aqueous solution onto the raw and activated a mixture of illite, kaolinite and chlorite clays from area of Zorbatiya (east of Iraq).The chemical treatment involved alkali and acid activation. The alkali activation obtained by treated the raw clay (RC) with 5M NaOH (ACSO) and the acid activation founded by treated it with 0.25M HCl (ACH) and 0.25M H_2 〖SO〗_4 (ACS). The thermal treatment carried out by calcination the produce activated clay at 750oC for acid activation and 105oC for alkali activation. Batch adsorption method was used to study the adsorption of orange G dye onto raw and activated clays. The impact of different factors related to the adsorption process was studied such as: agitation time, clay dosage, solution pH, starting OG dye concentration, temperature and ionic strength. The adsorption process was described by using Langmuir, Freundlich, Temkin and Dubinin-Raduchkevish isotherm models. Thermodynamic functions like change in enthalpy〖∆H〗^°, change in entropy 〖∆S〗^° and change in Gibbs free energy 〖∆G〗^°were estimated based on Vanʼt Hoff equation.

scholarly journals Orange Peel As Low-Cost Adsorbent In The Elimination Of Cd(Ii) Ions: Kinetics, Isotherm, Thermodynamic And Optimization Evaluations

2020 ◽  
Author(s):  
Fola Temilade Akinhanmi ◽  
Edwin Andrew Ofudje ◽  
Idowu Abideen Adeogun ◽  
Aina Peter ◽  
Joseph Mayowa Ilo
Keyword(s):  
Contact Time ◽  
Adsorption Process ◽  
Low Cost ◽  
Orange Peel ◽  
Polluted Water ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Human Beings ◽  
Solution Ph ◽  
Adsorbent Dosage

Abstract The presence of heavy metals in polluted water is known not only to cause stern harm to marine organisms but also to terrestrial plants and animals including human beings. This research applied low-cost and environmental benign adsorbent primed from waste orange peel (OP) for the removal of Cd(II) ions from aqueous solution via batch adsorption process. The surface properties of the orange peel powder were studied using Scanning Electron Microscopy (SEM), X-ray spectroscopy (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). Operational conditions like temperature, contact time, sorbent dosage, solution pH and initial adsorbate concentration were investigated. The utmost uptake of Cd(II) ion was obtained at a contact time of 120 mins, initial metal concentration of 240 mg/L, adsorbent dosage of 0.04 g/L, temperature of 45 °C and solution pH of 5.5. Equilibrium results showed that the orange peel adsorbent has an adsorption capacity of 128.23 mg/g as obtained from the Langmuir isotherm. The adsorption kinetics data followed a pseudo-first-order kinetic model with correlation coefficient (R2) >0.9 and low standard % error values. The adsorption process was found to be endothermic in nature with enthalpy of 0.0046 kJ mol−1 and entropy of-636.865 Jmol-1K-1 respectively. Results from the optimization study indicated that higher adsorbent dosage and lower Cd(II) ion concentration increased the percentage of Cd (II) ion removal. Thus, orange peel could be used in the removal of Cd(II) ion from aqueous solutions.

scholarly journals Efficient removal of radiocobalt and manganese from their binary aqueous solutions by batch adsorption process using PAN/HDTMA/KCuHCF composite

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Moustafa A. Hamoud ◽  
Karam F. Allan ◽  
Refaat R. Ayoub ◽  
Mohamed Holeil ◽  
Mamdoh R. Mahmoud
Keyword(s):  
Adsorption Process ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Hexadecyltrimethylammonium Bromide ◽  
Order Kinetic ◽  
Solution Ph ◽  
Copper Hexacyanoferrate ◽  
Adsorption Processes ◽  
Order Kinetic Model ◽  
Ph Range

AbstractSimultaneous removal of radiocobalt and manganese by adsorption onto polyacrylonitrile/hexadecyltrimethylammonium bromide/potassium copper hexacyanoferrate (PAN/HDTMA/KCuHCF) composite was studied. The synthesized composite was characterized by Fourier-transformed infrared (FT-IR), thermogravimetric analysis (TGA) and X-ray diffraction (XRD). The influence of the solution pH was studied in the range 1.5–7.8 and the results showed the effectiveness of the synthesized composite for simultaneous adsorption of radiocobalt and manganese in the pH range 2.5–6 at an adsorbent mass of 4 g/L. Adsorption kinetic data of manganese at the studied concentrations were best fitted by pseudo-second-order kinetic model and the diffusion study showed that the adsorption process was controlled by film diffusion. Thermodynamic parameters (ΔGo, ΔHo and ΔSo) were estimated and the results indicated that adsorption processes of the concerned (radio)toxicants were spontaneous and endothermic in nature. Of the studied isotherm models, Freundlich and Langmuir were the best ones for describing the adsorption isotherm data of radiocobalt and manganese, respectively. The adsorption capacity of PAN/HDTMA/KCuHCF was found to be 23.629 (for radiocobalt) and 62.854 (for manganese). Desorption of Radiocobalt and manganese loaded onto PAN/HDTMA/KCuHCF composite was studied using various desorbing agents at different concentrations.

scholarly journals Adsorption of Chromium(VI) onto Freshwater Snail Shell-Derived Biosorbent from Aqueous Solutions: Equilibrium, Kinetics, and Thermodynamics

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Xuan Hoa Vu ◽  
Lan Huong Nguyen ◽  
Huu Tap Van ◽  
Dinh Vinh Nguyen ◽  
Thu Huong Nguyen ◽  
...  
Keyword(s):  
Experimental Data ◽  
Aqueous Solutions ◽  
Contact Time ◽  
Low Cost ◽  
Freshwater Snail ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Adsorption Mechanisms

In this study, freshwater snail shells (FSSs) containing CaCO3 were used as a low-cost biosorbent for removing Cr(VI) from aqueous solutions. The characteristics of FSS and mechanism of Cr(VI) adsorption onto FSS were investigated. The FSS biosorbent was characterized using nitrogen adsorption/desorption isotherm, X-ray diffraction, scanning electron microscopy with energy dispersive spectroscopy, and Fourier transform infrared spectroscopy. The adsorption mechanism was determined by conducting various batch adsorption experiments along with fitting experimental data with various adsorption models. Batch adsorption experiments were conducted as a function of solution pH, contact time, biosorbent dose, and initial Cr(VI) concentration. Results indicated that pH = 2, a contact time of 120 min, and an initial Cr(VI) concentration of 30 mg/L at 20°C were the best conditions for adsorption of Cr(VI) onto FSS. The Cr(VI) adsorption onto FSS decreased with an increase in temperature from 20 to 40°C. The obtained maximum adsorption capacity was 8.85 mg/g for 2 g/L of FSS dose with 30 mg/L of initial Cr(VI) at 20°C. The adsorption equilibrium data fit well with the Sips and Langmuir isotherm models at 20°C with a high R2 of 0.981 and 0.975, respectively. Also, a good correlation between the experimental data and the pseudo-second-order model was achieved, with the highest R2 of 0.995 at 20°C. The adsorption mechanisms were electrostatic interaction and ion exchange. Simultaneously, this mechanism was also controlled by film diffusion. The Cr(VI) adsorption process was irreversible, spontaneous (−∆G°), exothermic (∆H° is negative), and less random (∆S° is negative). In conclusion, freshwater snail shells have the potential as a renewable adsorbent to remove toxic metals from wastewater.

Utilisation of Biomass and Hybrid Biochar from Elephant Grass and Low Density Polyethylene for the Competitive Adsorption of Pb(II), Cu(II), Fe(II) and Zn(II) from Aqueous Media

2020 ◽  
Vol 13 ◽  
Author(s):  
Joshua O. Ighalo ◽  
Lois T. Arowoyele ◽  
Samuel Ogunniyi ◽  
Comfort A. Adeyanju ◽  
Folasade M. Oladipo-Emmanuel ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Removal Efficiency ◽  
Contact Time ◽  
Competitive Adsorption ◽  
Adsorption Process ◽  
Aqueous Media ◽  
Polluted Water ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Elephant Grass

Background: The presence of pollutants in polluted water is not singularized hence pollutant species are constantly in competition for active sites during the adsorption process. A key advantage of competitive adsorption studies is that it informs on the adsorbent performance in real water treatment applications. Objective: This study aims to investigate the competitive adsorption of Pb(II), Cu(II), Fe(II) and Zn(II) using elephant grass (Pennisetum purpureum) biochar and hybrid biochar from LDPE. Method: The produced biochar was characterised by Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR). The effect of adsorption parameters, equilibrium isotherm modelling and parametric studies were conducted based on data from the batch adsorption experiments. Results: For both adsorbents, the removal efficiency was >99% over the domain of the entire investigation for dosage and contact time suggesting that they are very efficient for removing multiple heavy metals from aqueous media. It was observed that removal efficiency was optimal at 2 g/l dosage and contact time of 20 minutes for both adsorbent types. The Elovich isotherm and the pseudo-second order kinetic models were best-fit for the competitive adsorption process. Conclusion: The study was able to successfully reveal that biomass biochar from elephant grass and hybrid biochar from LDPE can be used as effective adsorbent material for the removal of heavy metals from aqueous media. This study bears a positive implication for environmental protection and solid waste management.

scholarly journals Removal of Cadmium(II) from Water using Modified Citrus limettioides Peels: Thermodynamic and Isotherm Studies

2019 ◽  
Vol 32 (1) ◽  
pp. 73-78
Author(s):  
P. Janaki ◽  
R. Sudha ◽  
T.S. Sribharathi ◽  
P. Anitha ◽  
K. Poornima ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Low Cost ◽  
Raw Material ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Adsorption Method ◽  
Chemically Modified ◽  
Adsorption Performance ◽  
Monolayer Adsorption ◽  
Isotherm Equations

The adsorption performance of sulphuric acid treated low cost adsorbent synthesized by using Citrus limettioides peel as an effective raw material for the removal of cadmium(II) from water. The batch adsorption method was carried out to optimize some parameters like contact time, pH and adsorbent dose. The nonlinear isotherm equations were used to calculate the different isotherm constant of five isotherm models namely Freundlich, Langmuir, Dubinin-Radushkevich, Redlich-Peterson and Sips. The Langmuir monolayer adsorption capacity of chemically modified Citrus limettioides peel was found to be 287.60 mg g-1. The negative values of ΔGº and ΔHº showed that the adsorption process is spontaneous and exothermic.

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

scholarly journals Characterization of Residual Biomasses and Its Application for the Removal of Lead Ions from Aqueous Solution

2019 ◽  
Vol 9 (21) ◽  
pp. 4486 ◽  
Author(s):  
Candelaria Tejada-Tovar ◽  
Angel Darío Gonzalez-Delgado ◽  
Angel Villabona-Ortiz
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Mesoporous Structure ◽  
Isotherm Models ◽  
Solution Ph ◽  
Batch Mode ◽  
Suitable Alternative

The removal of water pollutants has been widely addressed for the conservation of the environment, and novel materials are being developed as adsorbent to address this issue. In this work, different residual biomasses were employed to prepare biosorbents applied to lead (Pb(II)) ion uptake. The choice of cassava peels (CP), banana peels (BP), yam peels (YP), and oil palm bagasse (OPB) was made due to the availability of such biomasses in the Department of Bolivar (Colombia), derived from agro-industrial activities. The materials were characterized by ultimate and proximate analysis, Fourier Transform Infrared Spectroscopy (FTIR), Brunauer-Emmett-Teller analysis (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive X-Ray Spectroscopy (EDS) in order to determine the physicochemical properties of bioadsorbents. The adsorption tests were carried out in batch mode, keeping the initial metal concentration at 100 ppm, temperature at 30 °C, particle size at 1 mm, and solution pH at 6. The experimental results were adjusted to kinetic and isotherm models to determine the adsorption mechanism. The remaining concentration of Pb(II) in solution was measured by atomic absorption at 217 nm. The functional groups identified in FTIR spectra are characteristic of lignocellulosic materials. A high surface area was found for all biomaterials with the exception of yam peels. A low pore volume and size, related to the mesoporous structure of these materials, make these bioadsorbents a suitable alternative for liquid phase adsorption, since they facilitate the diffusion of Pb(II) ions onto the adsorbent structure. Both FTIR and EDS techniques confirmed ion precipitation onto adsorbent materials after the adsorption process. The adsorption tests reported efficiency values above 80% for YP, BP, and CP, indicating a good uptake of Pb(II) ions from aqueous solution. The results reported that Freundlich isotherm and pseudo-second order best fit experimental data, suggesting that the adsorption process is governed by chemical reactions and multilayer uptake. The future prospective of this work lies in the identification of alternatives to reuse Pb(II)-contaminated biomasses after heavy metal adsorption, such as material immobilization.

Sign in / Sign up

Export Citation Format

Share Document