scholarly journals EXPERIMENTAL AND NUMERICAL STUDIES OF PRESSURE AND GAP LENGTH EFFECTS ON ENERGY DEPOSITION IN SPARK DISCHARGE

2021 ◽  
pp. 92-97
Author(s):  
K.V. Korytchenko ◽  
I.S. Varshamova ◽  
D.V. Meshkov ◽  
D.P. Dubinin ◽  
R.I. Kovalenko ◽  
...  

A study of the influence of the discharge gap length and the initial gas pressure on the energy deposition into the discharge channel was done. The study was conducted at the same total discharge energy. It is experimentally shown that the connection of the voltage probe to the discharge circuit significantly affects the discharge current. The determination of the energy deposited into the spark channel is based on the results of numerical simulation of the spark channel development. Experimentally measured discharge currents at different pressures and the gap length were used as initial data for the calculation. Based on the obtained results, it is determined which of the factors (the initial pressure or the gap length) has the strongest influence on the energy input into the spark channel.

2019 ◽  
Author(s):  
K.V. Korytchenko ◽  
R.S. Tomashevskyi ◽  
I.S. Varshamova ◽  
D.P. Dubinin ◽  
A.A. Lisnyak ◽  
...  

An influence of initial gas pressure on energy deposited by spark discharge in nitrogen during the spark channel expansion is evaluated. Influence of the pressure on efficiency of energy deposition and emitted energy in a discharge channel is simulated. Dependencies of dynamic of energy input and an energy correlation coefficient on the pressure are found out. It was suggested to use an average value of the correlation coefficient to model a load of spark channel by the any initial pressure when a spark load is formed by atmospheric conditions.


2009 ◽  
Vol 16 (2) ◽  
pp. 143-151 ◽  
Author(s):  
Robin L. Owen ◽  
James M. Holton ◽  
Clemens Schulze-Briese ◽  
Elspeth F. Garman

Accurate measurement of photon flux from an X-ray source, a parameter required to calculate the dose absorbed by the sample, is not yet routinely available at macromolecular crystallography beamlines. The development of a model for determining the photon flux incident on pin diodes is described here, and has been tested on the macromolecular crystallography beamlines at both the Swiss Light Source, Villigen, Switzerland, and the Advanced Light Source, Berkeley, USA, at energies between 4 and 18 keV. These experiments have shown that a simple model based on energy deposition in silicon is sufficient for determining the flux incident on high-quality silicon pin diodes. The derivation and validation of this model is presented, and a web-based tool for the use of the macromolecular crystallography and wider synchrotron community is introduced.


Author(s):  
Olga Popova

The asteroid impact near the Russian city of Chelyabinsk on February 15, 2013, was the largest airburst on Earth since the 1908 Tunguska event, causing a natural disaster in an area with a population exceeding 1 million. On clear morning at 9:20 a.m. local time, an asteroid about 19 m in size entered the Earth atmosphere near southern Ural Mountains (Russia) and, with its bright illumination, attracted the attention of hundreds of thousands of people. Dust trail in the atmosphere after the bolide was tens of kilometers long and was visible for several hours. Thousands of different size meteorites were found in the areas south-southwest of Chelyabinsk. A powerful airburst, which was formed due to meteoroid energy deposition, shattered thousands of windows and doors in Chelyabinsk and wide surroundings, with flying glass injuring many residents. The entrance and destruction of the 500-kt Chelyabinsk asteroid produced a number of observable effects, including light and thermal radiation; acoustic, infrasound, blast, and seismic waves; and release of interplanetary substance. This unexpected and unusual event is the most well-documented bolide airburst, and it attracted worldwide attention. The airburst was observed globally by multiple instruments. Analyses of the observational data allowed determination of the size of the body that caused the superbolide, its velocity, its trajectory, its behavior in the atmosphere, the strength of the blast wave, and other characteristics. The entry of the 19-m-diameter Chelyabinsk asteroid provides a unique opportunity to calibrate the different approaches used to model meteoroid entry and to calculate the damaging effects. The recovered meteorite material was characterized as brecciated LL5 ordinary chondrite, in which three different lithologies can be distinguished (light-colored, dark-colored, and impact-melt). The structure and properties of meteorites demonstrate that before encountering Earth, the Chelyabinsk asteroid had experienced a very complex history involving at least a few impacts with other bodies and thermal metamorphism. The Chelyabinsk airburst of February 15, 2013, was exceptional because of the large kinetic energy of the impacting body and the damaging airburst that was generated. Before the event, decameter-sized objects were considered to be safe. With the Chelyabinsk event, it is possible, for the first time, to link the damage from an impact event to a well-determined impact energy in order to assess the future hazards of asteroids to lives and property.


2013 ◽  
Vol 53 ◽  
pp. 10001 ◽  
Author(s):  
J. Rosado ◽  
P. Gallego ◽  
D. García-Pinto ◽  
F. Blanco ◽  
F. Arqueros

2018 ◽  
Vol 17 (2) ◽  
pp. 03
Author(s):  
L. Pizzuti ◽  
C. A. Martins ◽  
L. R. Santos

This paper presents a very detailed description of a new cylindrical constant volume combustion chamber designed for laminar burning velocity determination of gaseous mixtures at ambient temperature and initial pressure up to 6 bar. The experimental setup, the experimental procedure and the determination of the range of flame radius for laminar burning determination are all described in details. The laminar burning velocity of twelve synthetic biogas mixtures has been studied. Initial pressure varying between 1 and 5 bar, equivalence ratios, f, between 0.7 and 1.1 and percentage dilution, with a mixture of CO2 and N2, between 35 and 55% have been considered. Five experiments were run for each mixture providing a maximum percentage standard deviation of 8.11%. However, for two third of the mixtures this value is lower than 3.55%. A comparison with simulation using PREMIX for both GRI-Mech 3.0 and San Diego mechanisms has provided closer agreement for mixtures with equivalence ratio closer to stoichiometry whereas for f = 0.7 the deviation is larger than 15% for all pressures. Mixtures with lower equivalence ratio, higher dilution percentage and higher initial pressure presents the lower values of laminar burning velocity.


2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Riccardo Scarcelli ◽  
Anqi Zhang ◽  
Thomas Wallner ◽  
Sibendu Som ◽  
Jing Huang ◽  
...  

With the engine technology moving toward more challenging (highly dilute and boosted) operation, spark-ignition processes play a key role in determining flame propagation and completeness of the combustion process. On the computational side, there is plenty of spark-ignition models available in literature and validated under conventional, stoichiometric spark ignition (SI) operation. Nevertheless, these models need to be expanded and developed on more physical grounds since at challenging operation they are not truly predictive. This paper reports on the development of a dedicated model for the spark-ignition event at nonquiescent, engine-like conditions, performed in the commercial CFD code converge. The developed methodology leverages previous findings that have expanded the use and improved the accuracy of Eulerian-type energy deposition models. In this work, the Eulerian energy deposition is coupled at every computational time-step with a Lagrangian-type evolution of the spark channel. Typical features such as spark channel elongation, stretch, and attachment to the electrodes are properly described to deliver realistic energy deposition along the channel during the entire ignition process. The numerical results are validated against schlieren images from an optical constant volume chamber and show the improvement in the simulation of the spark channel during the entire ignition event, with respect to the most commonly used energy deposition approach. Further developmental pathways are discussed to provide more physics-based features from the developed ignition model in the future.


Proceedings ◽  
2019 ◽  
Vol 42 (1) ◽  
pp. 73
Author(s):  
Jorge Otero ◽  
Ivan Felis

Hadrontherapy has been constantly evolving in leaps and bounds since the 1950s, when the use of heavy particles was proposed as an alternative treatment to radiotherapy with gamma rays or electrons. The main objective of this treatment is to maximize the dose applied to the tumour, avoiding damage to the surrounding tissue. One of the keys to the success of hadrontherapy is to achieve instantaneous monitoring of the energy deposition in the environment. Since energy deposition leads to the generation of a thermoacoustic pulse, acoustic technologies have been tested with successful results. However, for this purpose, it is essential to increase the sensitivity of the sensors for the acoustical signal and, therefore, to optimize their geometry as a function of the beam that would be used. We have studied a PTZ material in volumetric and surface volumes through experimental measures and FEM methods. In this text, we start with numerical studies which determine the dependence of the thermoacoustic signal frequency with the energy and duration of the hadron beam.


REAKTOR ◽  
2012 ◽  
Vol 14 (2) ◽  
pp. 109 ◽  
Author(s):  
Yuswan Muharam ◽  
Chandra Hadiwijaya ◽  
Jacquin Suryadi

One of the characteristics of gasoline fuel is anti-knock property represented by its octanenumber. The determination of octane numbers in Indonesia is by using cooperative fuel researchengines. The usage of cooperative fuel research engines in Indonesia has constraints, i.e. the limitednumber of the units and the old age. This study aims to obtain the octane numbers of commercialfuels by using kinetic models. The kinetics models of the oxidation and combustion of primaryreference fuel and multi component hydrocarbons are used to calculate the ignition delay times ofprimary reference fuel and commercial fuels, respectively. The ignition delay times of primaryreference fuel and commercial fuels are calculated at the same initial pressure and temperature, aswell as the same equivalence ratio. The octane number of a commercial fuel is known if its ignitiondelay time agrees with that of PFR possessing a certain volume percentage of isooctane. The modelgenerates the octane numbers of commercial fuels BB-A being 92.5, BB-B being 94.5, BB-C being89, BB-D being 90.5 and BB-E being 91.5 with the good agreement with those claimed by the fuelproducers. Salah satu karakteristik bahan bakar bensin adalah sifat anti ketukan yang dinyatakan dengan angkaoktana. Penentuan angka oktana di Indonesia menggunakan mesin CFR (cooperative fuel research).Pemakaian mesin CFR di Indonesia memiliki kendala, yaitu jumlah unit terbatas dan usia tua.Penelitian ini bertujuan mendapatkan angka oktana bahan bakar komersial dengan menggunakanmodel kinetika. Model kinetika oksidasi dan pembakaran bahan bakar rujukan utama dan modelhidrokarbon multikomponen yang telah divalidasi masing-masing digunakan untuk menghitungwaktu tunda ignisi bahan bakar rujukan utama dan bahan bakar komersial. Waktu tunda ignisibahan bakar rujukan utama dan bahan bakar komersial dihitung pada tekanan dan temperatur awal,serta rasio ekuivalensi yang sama. Angka oktana suatu bahan bakar komersial diketahui apabilawaktu tunda ignisinya cocok dengan waktu tunda ignisi bahan bakar rujukan utama yang memilikipersen volume isooktana tertentu. Model menghasilkan angka oktana bahan bakar komersial BB-Asebesar 92,5, BB-B 94,5, BB-C 89, BB-D 90,5 dan BB-E 91,5 yang memiliki ketepatan yang tinggiterhadap klaim produser bahan bakar komersial.


Sign in / Sign up

Export Citation Format

Share Document