scholarly journals Pengaruh Penambahan Sat Additive Addition H.E Terhadap Kuat Tekan Beton

2020 ◽  
Vol 2 (1) ◽  
pp. 31-57
Author(s):  
Ni Ketut Sri Astati Sukawati
Keyword(s):  
Compressive Strength ◽  
Concrete Mixture ◽  
Partial Replacement ◽  
Work Related ◽  
Coarse Aggregates ◽  
Alternative Ingredients ◽  
Fine Aggregates ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Artificial Stone

Concrete with various variants is a basic requirement in building a building. The concrete mixture is diverse depending on the planning made beforehand. The cement mixture is usually in the form of a mixture of artificial stone, cement, water and fine aggregates and coarse aggregates. Aggregates (fine aggregates and coarse aggregates) function as fillers in concrete mixtures. (Subakti, A., 1994). However, in building construction, additives are often added, but there is still a sense of uncertainty at the time of dismantling the mold and the reference before the concrete reaches sufficient strength to carry its own weight and the carrying loads acting on it. To overcome the time of carrying out work related to concrete, it is necessary to find an alternative solution, for example by looking for alternative ingredients of concrete mixture on the basis of consideration without reducing the quality of the concrete. From the results of previous studies it was stated that due to the partial replacement of cement with Fly Ash, the strength of the pressure and tensile strength of the concrete had increased (Budhi Saputro, A., 2008). Based on the description above, the author seeks to examine how the compressive strength of concrete characteristics that occur by adding additives Addition H.E in the concrete mixture and is there any additive Additon H.E effect on the increase in the compressive strength characteristic of the concrete. From the results of the study, it was found that the compressive strength of the concrete with the addition of additives HE was that after the compressive strength test of the concrete cube was carried out and the analysis of concrete compressive strength of 10 specimens, in each experiment a cube specimen was made with the addition of additons. HE with a dose of 80 cc, 120 cc, and 200 cc can accelerate and increase the compressive strength of concrete characteristics.

scholarly journals Study of the Compressive Strength of Concrete with Partial Replacement of Recycled Coarse Aggregates

2021 ◽  
Vol 11 (3) ◽  
pp. 7191-7194
Author(s):  
X. H. Vu ◽  
T. C. Vo ◽  
V. T. Phan
Keyword(s):  
Compressive Strength ◽  
Recycled Aggregate ◽  
Concrete Mixture ◽  
Recycled Aggregates ◽  
Partial Replacement ◽  
Replacement Rate ◽  
Coarse Aggregates ◽  
Compressive Strength Of Concrete ◽  
Natural Aggregates

This paper presents a study on the compressive strength of concrete using recycled aggregates. The concrete was designed to have a 25MPa compressive strength and an 8cm slump. The rates of replacing natural aggregates with recycled coarse were 0%, 10%, and 20%. The test samples were compressed to determine their compressive strength value after 7, 14, and 28 days of curing. The results showed that the concrete slump did not change effectively at a 10% replacement rate. When using 20% recycled aggregates, the concrete was too hard and the homogeneity of the concrete mixture could not be guaranteed. The compressive strength slightly decreased using 10% of recycled aggregates and decreased significantly using 20%. Therefore, 20% of recycled aggregate replacement is not suitable. The results showed that using recycled aggregates at a rate of 10% is optimal.

Utilization of Brine Sludge in Controlled Low Strength Materials (CLSM)

2019 ◽  
Vol 801 ◽  
pp. 436-441
Author(s):  
Shin Jen Chen ◽  
Chao Shi Chen ◽  
Jyun Yong Jhan ◽  
Ruei Fu Chen
Keyword(s):  
Compressive Strength ◽  
Bearing Capacity ◽  
Strength Test ◽  
Drop Test ◽  
Coarse Aggregates ◽  
Fine Aggregates ◽  
Compressive Strength Test ◽  
Early Strength ◽  
Low Strength ◽  
Brine Sludge

Controlled low-strength materials (CLSM) have begun to apply in a lot of countries because CLSM could distribute randomly in complex sites. Manufacturing from chlor-alkali industry, the brine sludge was used to replace the composition in CLSM for resource application. In this study, the mix composition of brine sludge replaced only the fine aggregates or all of the aggregates. Examining the suitable composition, the ball drop test and the compressive strength test were carried out. The ball drop test was applied to determine the readiness of the CLSM to accept loads prior, and the bearing capacity at different ages were measured by the compressive strength test. The results of the ball drop test in different replacements was 7 - 11.5 cm. The replacement of fine aggregates satisified the rule of CLSM. Replacing all of the aggregates, the mixtures were over 7.6 cm, which meant that the early strength at 1 day were not sufficient. The value of compressive strength at 28 days was 1.709 - 21.37 kgf/cm2, conforming the requirement of CLSM. Overall, the mixture which replaced the fine aggregates met all the specified values of CLSM. In particular, the composition of coarse aggregates reduce to 250 kg/m3, the utalization of the brine sludge could be the most.

scholarly journals Comparison of Compressive Strength of Concrete by Partial Replacement of Cement with GGBS and Silica Fume with Sea Water Curing and Addition with Fibers

2021 ◽  
pp. 31-39
Author(s):  
A Aswani and Janardhan G
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
Sea Water ◽  
Glass Fibers ◽  
Vital Role ◽  
Strength Test ◽  
Partial Replacement ◽  
Compressive Strength Test ◽  
Water Curing ◽  
Compressive Strength Of Concrete

In construction world concrete plays a vital role, around 60% of structure consists of Concrete. However, the production of Portland cement, an essential constituent of concrete, leads to the release of significant amounts of CO2, depletion of natural resources and environmental degradation. This paper investigates the compressive strength of concrete by replacing cement with GGBS and silica fume effect of glass fibers on performance of concrete is studied. In this present work a humble attempt had been made to evaluate and compare the compressive strengths of GGBS blended concrete cubes with controlled concrete cubes cured under sea water for 28 days. By conducting the tests on the cubes, conclusions were drawn after plotting and analyzing the results. Compressive strength test is conducted on the samples after 28 days. The optimum value is obtained at 15% replacement with GGBS and 5% with Silica fume. In this study again we trailed addition with Glass fibers with the percentage of 0.5%,1.0%,1.5%, compressive strength have been studied. Finally at 1.0% addition we get maximum strength compared to controlled mix.

scholarly journals PENGARUH CANGKANG KEMIRI SEBAGAI PENGGANTI AGREGAT KASAR TERHADAP SIFAT MEKANIK BETON (EFFECT OF CANDLENUT SHELL AS SUBTITUTE COARSE AGGREGATE TO THE MECHANICAL PROPERTIES OF CONCRETE)

2018 ◽  
Author(s):  
Erniati Bachtiar
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Concrete Mixture ◽  
Construction Technology ◽  
Concrete Compressive Strength ◽  
Coarse Aggregates ◽  
Volume Weight ◽  
Compressive Strength Test

Concrete construction technology is directed to be sustainable and ecofriendly. The waste of the candlenut shell as a substitute for the coarse aggregate of concrete mixture is known that the candlenut shell has a hard texture so it may be used as a substitute for coarse aggregates in concrete. The purpose of the research was to determine the effect of Candlenut shell as a substitute of coarse aggregate on physical properties (slump test, bleeding, segregation, volume weight) and mechanical properties (compressive strength and tensile strength) of concrete using Candlenut shell as replacement material of the coarse aggregate. The variation of the research was percentage of the Candlenut shell in the concrete mixture, that was 0%, 25%, 50%, 75% and 100% to the coarse aggregate volume in the concrete mixture. Number of specimens in reseach was each 5 pieces each variation. Testing of mechanical properties of concrete (compressive strength and tensile strength) was performed at 28 days. Testing of the concrete for compressive strength test and tensile strength on age 28 days. Concrete using candlenut shell as a substitute of coarse aggregates has decreased compressive strength respectively 11.72 MPa (37.71%) for 25% candlenut shell; 15.54 MPa (50.00%) for 50% candlenut shell; 18.35 MPa (59.02%) for 75% candlenut shell; And 18,85 MPa (60,66%) for 100% candlenut shell from of the 0% candlenut shell with compressive strength of 31.08 Mpa. Concrete using for 25% candlenut shell as a substitute for coarse aggregates decreased tensile strength respectively of 0.95 MPa (28.70%) for 25% candlenut shell; 1.21 MPa (36.56%) for 50% candlenut shell; 1.27 MPa (38.37%) for 75% candlenut shell; And 1.40 MPa (42.30%) for 100% candlenut shell from of the 0% candlenut shell with the tensile strength of BN of 3.31 MPa. The decrease in the value of compressive strength and tensile strength is strongly influenced by the increasing percentage of Candlenut shells on concrete

A review: sustainable compressive strength properties of concrete mix with replacement by marble powder

2020 ◽  
Vol 1 (98) ◽  
pp. 11-23
Author(s):  
N. Sharma ◽  
M. Singh Thakur ◽  
P.L. Goel ◽  
P. Sihag
Keyword(s):  
Compressive Strength ◽  
Design Methodology ◽  
Strength Properties ◽  
Concrete Mixture ◽  
Fine Aggregates ◽  
Concrete Mix ◽  
Marble Powder ◽  
Compressive Strength Of Concrete ◽  
The Impact

Purpose: Over the years, various experiments have been performed to investigate the impact of marble powder within the concrete mixture. In the present study, a review has been done to check the persistence of marble dirt as the substitute for concrete constituents. Design/methodology/approach: Furthermore, the impact of marble powder as a replacement of cement and aggregates were reviewed. By reviewing previous studies, the result indicates that the use of waste marble powder in cement and aggregate was adequate to a certain range. Findings: By replacing cement with marble powder in a range between 5% to 10% by weight, it increases the compressive strength of concrete mix by 11.30% to 24.56%, compared to the nominal mix. According to the study, any further increase in the amount of marble powder in place of cement i.e, 12.5% to 20% replacement by weight, results in the reduction of compressive strength of concrete mix by 7.5% to 26.01%. Replacement of aggregates from 5% to 75% with marble powder increases the compressive strength of about 3.22% to 23.91% as compared to the nominal mix. Research limitations/implications: It was also concluded from the current study that, to obtain higher compressive strength, it is advantageous to replace fine aggregates with marble powder than the replacement of cement with the marble powder.

Assessment of Rice Husk Ash (RHA) and Calcium Chloride (CaCl2) on Compressive Strength of Concrete Grade 20

2018 ◽  
Vol 40 ◽  
pp. 22-29
Author(s):  
Joseph A. Ige ◽  
Mukaila A. Anifowose ◽  
Samson O. Odeyemi ◽  
Suleiman A. Adebara ◽  
Mufutau O. Oyeleke
Keyword(s):  
Compressive Strength ◽  
Calcium Chloride ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Conventional Concrete ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Strength Result

This research assessed the effect of Nigerian rice husk ash (RHA) and calcium chloride (CaCl2) as partial replacement of cement in concrete grade 20. Rice husk ash (RHA) is obtained by combustion of rice husk in a controlled temperature. The replacement of OPC with rice husk ash (RHA) were 0%, 5%, 10%, 15% and 20%. 1% of Calcium Chloride was blended with OPC/RHA in all the test specimens except from control mix. Concrete cubes of sizes 150mm x 150mm x 150mm were cast and cured in water for 7, 14 and 28 days respectively. Slump test was conducted on fresh concrete while density test and compressive strength test were conducted on hardened concrete. The slump results revealed that the concrete becomes less workable (stiff) as percentage increases. The compressive strength result at 28 days revealed that 5%RHA/1%CaCl2 have the highest strength of 26.82N/mm2 while 20%RHA/1%CaCl2 have the lowest strength (21.48N/mm2). Integration of 5%RHA/1%CaCl2 and 10%RHA/1%CaCl2 as cement replacement will produce a concrete of higher compressive strength compared to conventional concrete in grade 20 concrete.

scholarly journals Partial Replacement of Fine Aggregates, Coarse Aggregates, Cement in Concrete

2021 ◽  
Vol 4 (2) ◽  
pp. 48-51
Author(s):  
Akshay Chandel ◽  
Chandra Pal Gautam
Keyword(s):  
Compressive Strength ◽  
Crumb Rubber ◽  
Cost Comparison ◽  
Partial Replacement ◽  
Zero Energy ◽  
Coarse Aggregates ◽  
Zero Energy Building ◽  
Satisfactory Performance ◽  
Fine Aggregates ◽  
The Cost

Today, the need to protect environment is a moral obligation for human. The study investigates the suitability of using Crumb rubber as replacement of Fine aggregates, Waste Crushed tiles as Coarse aggregates and Bagasse as replacement of Cement. The results of the study revealed that the Compressive strength of the sample showed satisfactory performance. This experiment mainly deals with the manufacture of Concrete made from waste materials. The concrete cubes are tested under CTM for compressive strength. The cost comparison with the conventional concretes has revealed that Concrete made from these waste is preferred because it is more economical walling material in itself and permits the use of economical building techniques. Also by the use of concrete made from these wastes it allows the building to save its energy and Cost and enables the building to have a step forward towards Zero energy building and Economical also.

scholarly journals OPTIMIZING THE USE OF ROCK ASH AS FINE AGGREGATES WITH THE ADDITION OF ADDITIVES TO THE CONCRETE MIXTURE WITH A COMPRESSIVE STRENGTH OF 350 Kg/cm2

CI-TECH ◽  
2020 ◽  
Vol 1 (01) ◽  
pp. 45-48
Author(s):  
Triaswati ◽  
Srie Subekti ◽  
Sulchan Arifin ◽  
Febri Aditya
Keyword(s):  
Compressive Strength ◽  
Test Object ◽  
Concrete Mixture ◽  
Normal Concrete ◽  
Type D ◽  
Cylinder Test ◽  
Fine Aggregates ◽  
Stone Dust ◽  
Compressive Strength Of Concrete

Stone dust nowadays is a side product of the stone crushing industry, the quality of which is quite a lot that it becomes a waste that needs to be handled. This study is intended to find out the composition of stone dust by adding some additive substance type D and type F to reach a compressive strength of 350 kg/cm2. The variation of percentage of stone dust on the composition of concrete mixture is 0%, 20%, 40%, 60%, 80%, 100%. The design of concrete mixture composition refers to the procedure of making preparation of the normal concrete mixture. SNI 03-2384-1993. The size of the cylinder test object is 15 cm in diameter and 30 cm in height. The result of this research shows that the mixture using stone dust has quite an effect on the compressive strength of concrete. From the result of the experiment, it is shown that for compressive strength of 350 kg/cm2, we can use 100% of stone dust with a resulted compressive strength of 445 kg/cm2.

scholarly journals Evaluation of compressive strength of concrete with metakaolin using different levelling techniques

2021 ◽  
Vol 10 (3) ◽  
pp. e31510313341
Author(s):  
Ayrton Wagner dos Santos Gomes de Sá ◽  
Yane Coutinho ◽  
Renan Gustavo Pacheco Soares ◽  
Fernanda Cavalcanti Ferreira ◽  
Arnaldo Manoel Pereira Carneiro
Keyword(s):  
Compressive Strength ◽  
High Strength ◽  
Strength Test ◽  
Mix Design ◽  
Partial Replacement ◽  
Initial Strength ◽  
Compressive Strength Test ◽  
Mineral Additions ◽  
Hardened State ◽  
Compressive Strength Of Concrete

The partial replacement of cement by mineral additions such as metakaolin has been widely applied in the production of high-strength and durable concretes due to the pozzolanic action, allowing a reduction in the consumption of cement. Tests are performed to determine the mechanical properties of these materials, such as compressive strength, for which there are different levelling techniques of specimens, such as sulphur and neoprene, indicated for different resistance classes. The present study aimed to characterize the behaviour, in the hardened state, of concrete produced with high initial strength Portland cement (CPV-ARI) and metakaolin and evaluate the different levelling methods. Three groups of samples dosed by the IPT-EPUSP method, with mix designs of 1:3, 1:5, and 1:6, and replacements of 8 and 10% of cement by metakaolin, were subjected to compressive strength test, at the ages of 28 days, with levelling by neoprene, and 90 days, with levelling by sulphur. It was observed an increase in strength with addition of metakaolin at both ages. Comparing the results in the two ages, it was verified an increase in strength for the mix designs 1:5 and 1:6 and a reduction for the mix design 1:3. Such fact can be explained by the high strengths achieved by this mix design. As the levelling method used was sulphur, it is confirmed the imprecision of results for strengths above 50 MPa with this technique.

Sign in / Sign up

Export Citation Format

Share Document