scholarly journals Finite element analysis of concrete filled lean duplex stainless steel columns

2018 ◽  
Author(s):  
Dennis Lam ◽  
Jie Yang ◽  
Xianghe Dai
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Element Model ◽  
Element Analysis ◽  
Composite Columns ◽  
Steel Columns ◽  
Lean Duplex Stainless Steel ◽  
Filled Composite

In recent years, a new low nickel content stainless steel (EN 1.4162) commonly referred as ‘lean duplex stainless steel’ has been developed, which has over two times the tensile strength of the more familiar austenitic stainless steel but at approximately half the cost. This paper presents the finite element analysis of concrete filled lean duplex stainless steel columns subjected to concentric axial compression. To predict the performance of this form of concrete filled composite columns, a finite element model was developed and finite element analyses were conducted. The finite element model was validated through comparisons of the results obtained from the experimental study. A parametric study was conducted to examine the effect of various parameters such as section size, wall thickness, infill concrete strength, etc. on the overall behaviour and compressive resistance of this form of composite columns. Through both experimental and numerical studies, the merits of using lean duplex stainless steel hollow sections in concrete filled composite columns are highlighted. In addition, a new formula based on the Eurocode 4 is proposed to predict the cross-section capacity of the concrete filled lean duplex stainless steel composite columns subjected to axial compression.

scholarly journals Finite Element Analysis on Block Shear Mechanism of Lean Duplex Stainless Steel Welded Connections

2021 ◽  
Vol 11 (7) ◽  
pp. 3283
Author(s):  
YongHyun Cho ◽  
Dong-Keon Kim ◽  
JunSu Kim ◽  
TaeSoo Kim
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Tensile Stress ◽  
Duplex Stainless Steel ◽  
Element Analysis ◽  
Lean Duplex Stainless Steel ◽  
Design Specifications ◽  
Block Shear ◽  
Fracture Simulation

The block shear equations specified in the current AISC specification for structural steel buildings and North American cold-formed steel design specifications are based on research results of carbon steel bolted connections. These equations were found to be inapplicable for the welded connections in the literature. This issue is primarily associated with the use of the incorrect assumption on block shear failure mechanism. The present paper examines the accuracy of various block shear equations available in the design specifications and in the literature. The paper also examines the shear hardening capacity and the level of tensile stress over the critical net area with the results of finite element analysis, in which the fracture simulation is considered. It shows that the block shear capacities of lean duplex stainless steel welded connections can be predicted accurately using tensile stress equal to 1.25Fu, as proposed in the literature.

Nonlinear Finite Element Analysis of the Bearing Capacity of a New Type of Column under Axial Load

2011 ◽  
Vol 255-260 ◽  
pp. 45-48 ◽  
Author(s):  
Ya Feng Xu ◽  
Xin Zhao ◽  
Yi Fu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Bearing Capacity ◽  
Axial Load ◽  
Load Capacity ◽  
Element Model ◽  
Steel Tube ◽  
Element Analysis ◽  
Composite Columns ◽  
Steel Ratio

Based on experimental research, the bearing performance of the new column (steel tube-reinforced concrete composite columns combination strengthened with angle steel and CFRP) has been studied in detail by finite element method. A finite element model is established based on a series of assumption. The load-displacement curves are obtained. The influence of steel ratio and thickness of CFRP layers to the bearing capacity is analyzed too. The result shows that both the steel ratio and the thickness of CFRP layers have great contribution to the axial load capacity. The finite element analysis results and theoretical analysis which are in good agreement show that simulation results are generally right.

Finite Element Analysis of a Pressure Vessel Subjected to an Internal Blast Load

2018 ◽  
Author(s):  
I. Barsoum ◽  
L. Sadiq
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stainless Steel ◽  
Pressure Vessel ◽  
Structural Response ◽  
Element Model ◽  
Decomposition Temperature ◽  
Blast Load ◽  
Element Analysis ◽  
Cause Of Failure

The objective of the current work is to model a stainless steel SA 316L autoclave explosion and rupture that occurred during a research laboratory experiment designed to study the thermal decomposition of ammonium tetrathiomolybdate in the presence of dimethyl sulfoxide (DSMO) in an autoclave. The explosion was believed to have occurred because DMSO was used in excess in the experiment and heated beyond its decomposition temperature. The aim of the current study is to investigate the effect of internal blast load on a pressure vessel made of stainless steel AISI 316L through finite element analysis. Numerical simulation using FEA is performed to better understand the cause of failure of the pressure vessel. The finite element model predicts very well the structural response and subsequent failure of the actual incident and the results reveal that the root cause to failure was an internal blast load, which arose from the decomposition of DMSO at high temperature.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis and Optimization of Long-Span Gantry NC Machining Center Structure

2011 ◽  
Vol 346 ◽  
pp. 379-384
Author(s):  
Shu Bo Xu ◽  
Yang Xi ◽  
Cai Nian Jing ◽  
Ke Ke Sun
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Method ◽  
Dynamic Performance ◽  
Plate Thickness ◽  
Element Model ◽  
Wall Structure ◽  
Characteristic Analysis ◽  
Element Analysis ◽  
Dynamic Performance Analysis

The use of finite element theory and modal analysis theory, the structure of the machine static and dynamic performance analysis and prediction using optimal design method for optimization, the new machine to improve job performance, improve processing accuracy, shorten the development cycle and enhance the competitiveness of products is very important. Selected for three-dimensional CAD modeling software-UG NX4.0 and finite element analysis software-ANSYS to set up the structure of the beam finite element model, and then post on the overall structure of the static and dynamic characteristic analysis, on the basis of optimized static and dynamic performance is more superior double wall structure of the beam. And by changing the wall thickness and the thickness of the inner wall, as well as the reinforcement plate thickness overall sensitivity analysis shows that changes in these three parameters on the dynamic characteristics of post impact. Application of topology optimization methods, determine the optimal structure of the beam ultimately.

Sign in / Sign up

Export Citation Format

Share Document