scholarly journals A study on the relationship between internal nozzle geometry and injected mass distribution of eight ECN Spray G nozzles.

2017 ◽  
Author(s):  
Katarzyna E Matusik ◽  
Daniel J Duke ◽  
Nicholas Sovis ◽  
Andrew B Swantek ◽  
Christopher F Powell ◽  
...  
Keyword(s):  
Mass Distribution ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Gasoline Direct Injection ◽  
Nozzle Geometry ◽  
Hole Density ◽  
Full Spectrum ◽  
Length Scales ◽  
X Ray ◽  
The Relationship

Gasoline direct injection (GDI) nozzles are manufactured to meet geometric specifications with length scales onthe order of a few hundred microns. The machining tolerances of these nominal dimensions are not always knowndue to the difficulty in accurately measuring such small length scales in a nonintrusive fashion. To gain insight intothe variability of the machined dimensions as well as any effects that this variability may have on the fuel spraybehavior, a series of measurements of the internal geometry and fuel mass distribution were performed on a set ofeight nominally duplicate GDI “Spray G” nozzles provided by the Engine Combustion Network. The key dimensionsof each of the eight nozzle holes were measured with micron resolution using full spectrum x-ray tomographicimaging at the 7-BM beamline of the Advanced Photon Source at Argonne National Laboratory. Fuel densitydistributions at 2 mm downstream of the nozzle tips were obtained by performing x-ray radiography measurementsfor many lines of sight. The density measurements reveal nozzle-to-nozzle as well as hole-to-hole density variations.The combination of high-resolution geometry and fuel distribution datasets allows spray phenomena to be linked tospecific geometric characteristics of the nozzle, such as variability in the hole lengths and counterbore diameters,and the hole inlet corner radii. This analysis provides important insight into which geometrical characteristics ofthe nozzles may have the greatest importance in the development of the injected sprays, and to what degreethese geometric variations might account for the total spray variability. The goal of this work is then to further theunderstanding of the relationship between internal nozzle geometry and fuel injection, provide input to improvecomputational models, and ultimately aid in optimizing injector design for higher fuel efficiency and lower emissionsengines.DOI: http://dx.doi.org/10.4995/ILASS2017.2017.4766

scholarly journals Eulerian CFD modeling of nozzle geometry effects on ECN Sprays A and D: assessment and analysis

2019 ◽  
Vol 21 (1) ◽  
pp. 73-88 ◽  
Author(s):  
Adrian Pandal ◽  
Jose M Garcia-Oliver ◽  
Jose M Pastor
Keyword(s):  
Turbulence Modeling ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Computational Effort ◽  
Diffuse Interface ◽  
Cfd Modeling ◽  
Nozzle Geometry ◽  
Nozzle Flow ◽  
X Ray ◽  
Geometry Effects

Diesel spray modeling is a multi-scale problem with complex interactions between different flow regions, that is, internal nozzle flow, near-nozzle region and developed spray, including evaporation and combustion. There are several modeling approaches that have proven particularly useful for some spray regions although they have struggled at other areas, while Eulerian modeling has shown promise in dealing with all characteristics at a reasonable computational effort for engineering calculations. In this work, the [Formula: see text]–Y single-fluid diffuse-interface model, based on scale separation assumptions at high Reynolds and Weber numbers, is used to simulate the engine combustion network Sprays A and D within a Reynolds-averaged Navier–Stokes turbulence modeling approach. The study is divided into two parts. First of all, the larger diameter Spray D is modeled from the nozzle flow till evaporative spray conditions, obtaining successful prediction of numerous spray metrics, paying special attention to the near-nozzle region where spray dispersion and interfacial surface area can be validated against measurements conducted at the Advanced Photon Source at Argonne National Laboratory, including both the ultra-small-angle X-ray scattering and the X-ray radiography. Afterwards, an analysis of the modeling predictions is made in comparison with previous results obtained for Spray A, considering the nozzle geometry effects in the modeling behavior.

Fuel Effects on Nozzle Flow and Spray Using Fully Coupled Eulerian Simulations

2015 ◽  
Author(s):  
Luis Bravo ◽  
Qingluan Xue ◽  
Sibendu Som ◽  
Christopher Powell ◽  
Chol-Bum M. Kweon
Keyword(s):  
Alternative Fuels ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Flow Dynamics ◽  
Nozzle Geometry ◽  
Nozzle Flow ◽  
Fuel Temperature ◽  
X Ray ◽  
The Impact ◽  
Fully Coupled

The objective of this study is to examine the impact of single and multi-component surrogate fuel mixtures on the atomization and mixing characteristics of non-reacting isothermal diesel engine sprays. An Eulerian modeling approach was adopted to simulate both the internal nozzle flow dynamics and the emerging turbulent spray in the near nozzle region in a fully-coupled manner. The Volume of Fluids (VoF) methodology was utilized to treat the two-phase flow dynamics including a Homogenous Relaxation approach to account for nozzle cavitation effects. To enable accurate simulations, the nozzle geometry and in-situ multi-dimensional needle lift and off-axis motion profiles have been characterized via the X-ray phase-contrast technique at Argonne National Laboratory. The flow turbulence is treated via the classical k–ϵ Reynolds Average Navier Stoke (RANS) model with in-nozzle and near field resolution of 30 μm. Several multi-component surrogate mixtures were implemented using linear blending rules to examine the behavior of petroleum, and alternative fuels including: JP-8, JP-5, Hydro-treated Renewable Jet (HRJ), Iso-Paraffinic Kerosene (IPK) with comparison to single-component n-dodecane fuel on ECN Spray A nozzle spray dynamics. The results were validated using transient rate-of-injection measurements from the Army Research Laboratory at Spray A conditions as well as projected density fields obtained from the line-of-sight measurements from X-ray radiography measurements at The Advanced Photon Source at Argonne National Laboratory. The conditions correspond to injection pressure, nominal fuel temperature, and ambient density of 1500 bar, 363 K, and 22.8 kg/m3, respectively. The simulation results provide a unique high-fidelity contribution to the effects of fuels on the spray mixing dynamics. The results can lead to improvements in fuel mixture distributions enhancing performance of military vehicles.

Synchrotron X-ray studies of metal-organic framework M2(2,5-dihydroxyterephthalate), M = (Mn, Co, Ni, Zn) (MOF74)

2012 ◽  
Vol 27 (4) ◽  
pp. 256-262 ◽  
Author(s):  
W. Wong-Ng ◽  
J. A. Kaduk ◽  
H. Wu ◽  
M. Suchomel
Keyword(s):  
Powder Diffraction ◽  
Metal Organic Framework ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Lattice Parameter ◽  
X Ray ◽  
Metal Organic ◽  
Sorbent Materials ◽  
Diffraction Patterns ◽  
Unsaturated Metal Sites

M2(dhtp)·nH2O (M = Mn, Co, Ni, Zn; dhtp = 2,5-dihydroxyterephthalate), known as MOF74, is a family of excellent sorbent materials for CO2 that contains coordinatively unsaturated metal sites and a honeycomb-like structure featuring a broad one-dimensional channel. This paper describes the structural feature and provides reference X-ray powder diffraction patterns of these four isostructural compounds. The structures were determined using synchrotron diffraction data obtained at beam line 11-BM at the Advanced Photon Source (APS) in the Argonne National Laboratory. The samples were confirmed to be hexagonal R 3 (No. 148). From M = Mn, Co, Ni, to Zn, the lattice parameter a of MOF74 ranges from 26.131 73(4) Å to 26.5738(2) Å, c from 6.651 97(5) to 6.808 83(8) Å, and V ranges from 3948.08 Å3 to 4163.99 Å3, respectively. The four reference X-ray powder diffraction patterns have been submitted for inclusion in the Powder Diffraction File (PDF).

scholarly journals NDE Development for Ceramics for Advanced Heat Engines

1991 ◽  
Author(s):  
R. W. McClung ◽  
D. R. Johnson
Keyword(s):  
Computed Tomography ◽  
Process Development ◽  
Low Voltage ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Ceramic Technology ◽  
X Ray ◽  
Oak Ridge ◽  
Heat Engines ◽  
X Ray Computed

Following an assessment of needs for NDT and characterization of ceramics for the DOE program, Ceramic Technology for Advanced Heat Engines (CTAHE), many NDT projects have been implemented under the sponsorship of CTAHE to address the needs. Tasks at Argonne National Laboratory have involved X-ray computed tomography and nuclear magnetic resonance imaging. The Oak Ridge National Laboratory has emphasized high-frequency ultrasonics, low-voltage radiography, and an advanced system for X-ray computed tomography. A brief investigation was made by Radiation Sciences, Inc., into the feasibility of synchrotron-computed tomography for ceramics. New programs recently initiated at Allison and Garrett integrate ultrasonics, radiography, and other methods into a major effort on life prediction. New programs at Norton and GTE on advanced processing of ceramics also place heavy emphasis on several methods of NDT for process development and control. Initial work on NDT standards has begun in ASTM Committees E-7 and C-28.

On the structure of aragonite

2005 ◽  
Vol 61 (2) ◽  
pp. 129-132 ◽  
Author(s):  
E. N. Caspi ◽  
B. Pokroy ◽  
P. L. Lee ◽  
J. P. Quintana ◽  
E. Zolotoyabko
Keyword(s):  
High Resolution ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Orthorhombic Symmetry ◽  
X Ray ◽  
Impurity Atoms ◽  
Synchrotron Powder Diffraction ◽  
Refinement Procedure ◽  
Photon Source

High-resolution synchrotron powder diffraction measurements were carried out at the 32-ID beamline of the Advanced Photon Source of Argonne National Laboratory in order to clarify the structure of geological aragonite, a widely abundant polymorph of CaCO3. The investigated crystals were practically free of impurity atoms, as measured by wavelength-dispersive X-ray spectroscopy in scanning electron microscopy. A superior quality of diffraction data was achieved by using the 11-channel 111 Si multi-analyzer of the diffracted beam. Applying the Rietveld refinement procedure to the high-resolution diffraction spectra, we were able to extract the aragonite lattice parameters with an accuracy of about 20 p.p.m. The data obtained unambiguously confirm that pure aragonite crystals have orthorhombic symmetry.

First X-Ray Microprobe and Microspectroscopy Results From The Gsecars Sector At The Advanced Photon Source

1997 ◽  
Vol 3 (S2) ◽  
pp. 905-906
Author(s):  
Mark L. Rivers ◽  
Stephen R. Sutton ◽  
Peter Eng ◽  
Matthew Newville
Keyword(s):  
National Laboratory ◽  
Argonne National Laboratory ◽  
Third Generation ◽  
X Rays ◽  
Environmental Sciences ◽  
X Ray ◽  
State Determination ◽  
X Ray Absorption ◽  
The Magnetic Field ◽  
Photon Source

The Advanced Photon Source (APS) at Argonne National Laboratory is a third-generation synchrotron x-ray source, optimized for producing x-rays from undulators. Such undulator sources provide extremely bright, quasi-monochromatic radiation which is ideal for an x-ray microprobe. Such microprobes can be used for trace element quantification with x-ray fluorescence, or for chemical state determination with x-ray absorption spectroscopy. The GeoSoilEnviroCARS (GSECARS) sector at the APS is building an x-ray microprobe for research in earth, planetary, soil and environmental sciences.The GSECARS undulator source is a standard APS Undulator “A” which is a 3.3 cm period device with 72 periods. The energies of the undulator peaks can be varied by adjusting the gap, and hence the magnetic field of the undulator. The energy of the first harmonic can be varied in this way from approximately 3.1 keV to 14 keV. A measured undulator spectrum is shown in Figure 1.

Local Measurements in Cavitating Flow by Ultra-Fast X-Ray Imaging

2009 ◽  
Author(s):  
O. Coutier-Delgosha ◽  
A. Vabre ◽  
M. Hocevar ◽  
R. Delion ◽  
A. Dazin ◽  
...  
Keyword(s):  
National Laboratory ◽  
Argonne National Laboratory ◽  
Velocity Fields ◽  
Cavitating Flow ◽  
Research Teams ◽  
X Ray ◽  
X Ray Imaging ◽  
Local Measurements ◽  
Velocity Pressure ◽  
Photon Source

The present paper presents an experimental method to measure velocity fields in a cavitating flow. Dynamics of the liquid phase and of the bubbles are both investigated. The measurements are based on ultra fast X-ray imaging performed at the APS (Advanced Photon Source) of the Argonne National Laboratory. This is collaboration between research teams devoted to fluid mechanics (LML laboratory, Laboratory for water and turbine machines) and experts in X-ray imaging (French atomic commission, Argonne National Laboratory). The experimental device consists of a millimetric Venturi test section associated with a transportable hydraulic loop. Various configurations of velocity, pressure, and temperature have been investigated. This first paper focuses on the experimental equipment and process, and also the description of the image processing which is performed to analyze the results and obtain the velocity fields of both phases within the cavitating areas. Promising preliminary results are also presented.

scholarly journals Development of combined microstructure and structure characterization facility forin situandoperandostudies at the Advanced Photon Source

2018 ◽  
Vol 51 (3) ◽  
pp. 867-882 ◽  
Author(s):  
Jan Ilavsky ◽  
Fan Zhang ◽  
Ross N. Andrews ◽  
Ivan Kuzmenko ◽  
Pete R. Jemian ◽  
...  
Keyword(s):  
Small Angle ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Incident Beam ◽  
Evolutionary Development ◽  
X Ray ◽  
X Ray Scattering ◽  
Wide Range ◽  
Photon Source ◽  
Ray Scattering

Following many years of evolutionary development, first at the National Synchrotron Light Source, Brookhaven National Laboratory, and then at the Advanced Photon Source (APS), Argonne National Laboratory, the APS ultra-small-angle X-ray scattering (USAXS) facility has been transformed by several new developments. These comprise a conversion to higher-order crystal optics and higher X-ray energies as the standard operating mode, rapid fly scan measurements also as a standard operational mode, automated contiguous pinhole small-angle X-ray scattering (SAXS) measurements at intermediate scattering vectors, and associated rapid wide-angle X-ray scattering (WAXS) measurements for X-ray diffraction without disturbing the sample geometry. With each mode using the USAXS incident beam optics upstream of the sample, USAXS/SAXS/WAXS measurements can now be made within 5 min, allowingin situandoperandomeasurement capabilities with great flexibility under a wide range of sample conditions. These developments are described, together with examples of their application to investigate materials phenomena of technological importance. Developments of two novel USAXS applications, USAXS-based X-ray photon correlation spectroscopy and USAXS imaging, are also briefly reviewed.

scholarly journals Maximum a posteriori estimation of crystallographic phases in X-ray diffraction tomography

2015 ◽  
Vol 373 (2043) ◽  
pp. 20140392 ◽  
Author(s):  
Doĝa Gürsoy ◽  
Tekin Biçer ◽  
Jonathan D. Almer ◽  
Raj Kettimuthu ◽  
Stuart R. Stock ◽  
...  
Keyword(s):  
National Laboratory ◽  
Spinous Process ◽  
Argonne National Laboratory ◽  
Three Dimensional ◽  
Polycrystalline Materials ◽  
Reconstruction Method ◽  
Diffraction Tomography ◽  
A Posteriori ◽  
X Ray Diffraction ◽  
X Ray

A maximum a posteriori approach is proposed for X-ray diffraction tomography for reconstructing three-dimensional spatial distribution of crystallographic phases and orientations of polycrystalline materials. The approach maximizes the a posteriori density which includes a Poisson log-likelihood and an a priori term that reinforces expected solution properties such as smoothness or local continuity. The reconstruction method is validated with experimental data acquired from a section of the spinous process of a porcine vertebra collected at the 1-ID-C beamline of the Advanced Photon Source, at Argonne National Laboratory. The reconstruction results show significant improvement in the reduction of aliasing and streaking artefacts, and improved robustness to noise and undersampling compared to conventional analytical inversion approaches. The approach has the potential to reduce data acquisition times, and significantly improve beamtime efficiency.

Sign in / Sign up

Export Citation Format

Share Document