Radiometric and Spectrophotometric Analysis of Third Generation Light-Emitting Diode (LED) Light-Curing Units

2007 ◽  
Vol 8 (2) ◽  
pp. 43-51 ◽  
Author(s):  
Barry M. Owens ◽  
Kelbin H. Rodriguez
Keyword(s):  
Spectral Distribution ◽  
Light Emitting Diode ◽  
Spectrophotometric Analysis ◽  
Battery Life ◽  
Light Sources ◽  
Third Generation ◽  
Light Emitting ◽  
Led Light ◽  
Restorative Materials ◽  
Light Curing

Abstract Aims Light-emitting diode (LED) polymerization of dental restorative materials has become increasingly popular. However, individual light-curing unit (LCU) functions (intensity and/or wavelength emission) may not conform to manufacturer specifications due to quality control issues. The purpose of this study was to evaluate the quality of irradiance, in terms of power density (intensity) and spectral distribution (peak wavelength), emitted from LED and quartz-tungsten halogen (QTH) LCUs in vitro. The battery expenditure of these LED units was also tested. Methods and Materials The intensity and spectral distribution from four third generation LED (Smartlite PS, Coltolux LED, radii Plus, Diopower) and one QTH (Schein Visible Cure) light sources were measured using six different dental curing light meters (Coltolux, Cure Right, Demetron 100, Demetron LED., Hilux, and Light Meter-200) and a visible-ultraviolet light spectrophotometer (Hitachi Elmer-Perkins). The battery life was also plotted for each light source following a 1500 second duration period. The data obtained from radiometric and spectrophotometric analysis was compared to manufacturer specifications. Results Radiometric evaluation revealed LED light units tested did not satisfy manufacturer claims for minimum intensities. Spectral emissions from the LED light sources did meet manufacturer requirements. No clinically appreciable battery drain was evidenced from testing all re-chargeable LED units. Conclusion Despite limitations LED technology appears to be an effective alternative for curing of lightactivated esthetic restorative materials. Additional advantages associated with LED curing lights include ergonomic handling capabilities, negative heat generation, and minimal maintenance concerns. Citation Owens BM, Rodriguez KH. Radiometric and Spectrophotometric Analysis of Third Generation Light- Emitting Diode (LED) Light-Curing Units. J Contemp Dent Pract 2007 February;(8)2:043-051.

Effectiveness of Second-generation Light-emitting Diode (LED) Light Curing Units

2007 ◽  
Vol 8 (2) ◽  
pp. 35-42 ◽  
Author(s):  
Fabrício Aulo Ogliari ◽  
Ulisses Bastos Campregher ◽  
Susana Maria Werner Samuel ◽  
Carmen Beatriz Borges Fortes ◽  
Alberth David Correa Medina ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Second Generation ◽  
Light Emitting Diode ◽  
Strength Properties ◽  
Knoop Hardness ◽  
Curing Time ◽  
Light Emitting ◽  
Led Light ◽  
Three Samples ◽  
Light Curing

Abstract Aim The purpose of this study was to evaluate the effectiveness of three commercially available light emitting diode (LED) light curing units (LCU) (Elipar FreeLight - 3M ESPE; UltraLume LED2 - Ultradent; and Single V - BioArt) for polymerizing Z250-A3 composite (3M ESPE) using Knoop hardness, polymerization depth, and flexural strength properties. Methods and Materials The XL 2500 (3M ESPE) LCU, which is a conventional halogen unit, was used as a control. In all cases the curing time was 20 seconds. Hardness was determined 24 hours after composite cure for 10 samples of 8 mm diameter and 2 mm height for each LCU tested. Samples were stored dry in a lightproof container prior to testing. The depth of cure of the composite was measured immediately after composite polymerization for each LCU using three samples 4 mm in diameter and 6 mm in height. Flexural strength was determined for five samples 24 hours after immersion in distilled water at 37°C. Each sample measured 25 mm in length, 2 mm in width, and 2 mm in height for each LCU tested. Conclusion The results were treated statistically for comparison of the LCUs. In all cases the results obtained by LED LCUs were not different or were higher than a conventional halogen LCU. Clinical Significance Second generation LED LCUs were as effective as/or more effective than a halogen LCU for polymerization of the used composite. The present study shows second generation LEDs have the potential to replace halogen LCUs. Citation Campregher UB, Samuel SMW, Fortes CBB, Medina ADC, Collares FMC, Ogliari FA. Effectiveness of Second-generation Light-emitting Diode (LED) Light Curing Units. J Contemp Dent Pract 2007 February;(8)2:035-042.

scholarly journals Microhardness of resin-based materials polymerized with LED and halogen curing units

2005 ◽  
Vol 16 (2) ◽  
pp. 98-102 ◽  
Author(s):  
Daniela Francisca Gigo Cefaly ◽  
Giovano Augusto de Oliveira Ferrarezi ◽  
Celiane Mary Carneiro Tapety ◽  
José Roberto Pereira Lauris ◽  
Maria Fidela de Lima Navarro
Keyword(s):  
Statistical Analysis ◽  
Light Emitting Diode ◽  
Surface Hardness ◽  
Bottom Surface ◽  
Halogen Lamp ◽  
Light Emitting ◽  
Led Light ◽  
Significant Difference ◽  
Light Curing ◽  
Curing Light

The purpose of this study was to evaluate the microhardness of resin-based materials polymerized with a LED (light-emitting diode) light-curing unit (LCU) and a halogen LCU. Twenty cylindrical specimens (3.0 mm in diameter and 2.0 mm high) were prepared for each tested material (Z100, Definite and Dyract). Specimens were light-cured with two LCUs (Ultraled and Curing Light 2500) for either 40 or 60 s on their top surfaces. Hardness was measured on top and bottom surfaces of each specimen. Statistical analysis was done by ANOVA and Tukey's test (p<0.05). There was no significant difference in hardness between LED LCU and halogen LCU for Z100 and Dyract on top surface. Conversely, lower hardness was recorded when Definite was light-cured with the LED LCU than with the halogen lamp. On bottom surface, hardness was significantly lower for all materials light-cured with LED LCU. Z100 was harder than Dyract and Definite regardless of the light curing unit. There was no significant difference in hardness between the exposure times on top surface. Higher hardness was obtained when the materials were light-cured for 60 s on bottom surface. The tested LED was not able to produce the same microhardness of resin-based materials as the halogen LCU.

scholarly journals A Practical Method to Design Reflector-Based Light-Emitting Diode Luminaire for General Lighting

2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Jinren Yan
Keyword(s):  
Light Emitting Diode ◽  
Spherical Surface ◽  
Target Surface ◽  
Practical Method ◽  
Optical Simulation ◽  
Light Sources ◽  
Aspheric Surface ◽  
Light Emitting ◽  
Led Light ◽  
Spherical Reflector

A reflector-based light-emitting diode (LED) luminaire structure that can achieve a large cut-off angle for general lighting is presented in this work. The proposed lighting unit mainly consists of a spherical reflector and a primary packaging lens that contains an aspheric surface and a spherical surface. The light rays emitted from the LED light source are well controlled by the spherical reflector and the aspheric surface of the lens for the purpose of obtaining a uniform illumination on the target surface. Both the ideal Lambertian LED and non-Lambertian LED light sources were employed to validate the proposed structure and the performance of the designed lighting units was analyzed by optical simulation. The results show that the light utilization efficiencies and the estimated uniformities are 92.96% and 91.11% for ideal Lambertian LED-based lighting unit and 93.31% and 91.64% for non-Lambertian LED-based lighting unit, respectively. Further analysis shows that the tolerances of horizontal, vertical, and rotational deviation of the both lighting units were about 2.0 mm, 1.0 mm, and 1.0°, respectively.

Battery Charge Affects the Stability of Light Intensity from Light-emitting Diode Light-curing Units

2017 ◽  
Vol 42 (5) ◽  
pp. 497-504 ◽  
Author(s):  
A Tongtaksin ◽  
C Leevailoj
Keyword(s):  
Light Intensity ◽  
Light Emitting Diode ◽  
Resin Composite ◽  
Bottom Surface ◽  
Light Emitting ◽  
Led Light ◽  
Battery Charge ◽  
Light Intensities ◽  
Light Curing ◽  
The Stability

SUMMARY This study investigated the influence of battery charge levels on the stability of light-emitting diode (LED) curing-light intensity by measuring the intensity from fully charged through fully discharged batteries. The microhardness of resin composites polymerized by the light-curing units at various battery charge levels was measured. The light intensities of seven fully charged battery LED light-curing units—1) LY-A180, 2) Bluephase, 3) Woodpecker, 4) Demi Plus, 5) Saab II, 6) Elipar S10, and 7) MiniLED—were measured with a radiometer (Kerr) after every 10 uses (20 seconds per use) until the battery was discharged. Ten 2-mm-thick cylindrical specimens of A3 shade nanofilled resin composite (PREMISE, Kerr) were prepared per LED light-curing unit group. Each specimen was irradiated by the fully charged light-curing unit for 20 seconds. The LED light-curing units were then used until the battery charge fell to 50%. Specimens were prepared again as described above. This was repeated again when the light-curing units' battery charge fell to 25% and when the light intensity had decreased to 400 mW/cm2. The top/bottom surface Knoop hardness ratios of the specimens were determined. The microhardness data were analyzed by one-way analysis of variance with Tukey test at a significance level of 0.05. The Pearson correlation coefficient was used to determine significant correlations between surface hardness and light intensity. We found that the light intensities of the Bluephase, Demi Plus, and Elipar S10 units were stable. The intensity of the MiniLED unit decreased slightly; however, it remained above 400 mW/cm2. In contrast, the intensities of the LY-A180, Woodpecker, and Saab II units decreased below 400 mW/cm2. There was also a significant decrease in the surface microhardnesses of the resin composite specimens treated with MiniLED, LY-A180, Woodpecker, and Saab II. In conclusion, the light intensity of several LED light-curing units decreased as the battery was discharged, with a coincident reduction in the units' ability to polymerize resin composite. Therefore, the intensity of an LED light-curing unit should be evaluated during the life of its battery charge to ensure that sufficient light intensity is being generated.

Responses of Favorita Potato Plantlets Cultured in Vitro under Fluorescent and Light-Emitting Diode (LED) Light Sources

2019 ◽  
Vol 96 (4) ◽  
pp. 396-402 ◽  
Author(s):  
Lili Jiang ◽  
Ziquan Wang ◽  
Guanghui Jin ◽  
Dianqiu Lu ◽  
Xuezhan Li
Keyword(s):  
Light Emitting Diode ◽  
Light Sources ◽  
Light Emitting ◽  
Led Light ◽  
Potato Plantlets

scholarly journals Comparison of the bonding strengths of second- and third-generation light-emitting diode light-curing units

2016 ◽  
Vol 46 (6) ◽  
pp. 364 ◽  
Author(s):  
Hee-Min Lee ◽  
Sang-Cheol Kim ◽  
Kyung-Hwa Kang ◽  
Na-Young Chang
Keyword(s):  
Light Emitting Diode ◽  
Third Generation ◽  
Light Emitting ◽  
Light Curing

PHOTOTHERAPY FOR MILD TO MODERATE ACNE VULGARIS WITH PORTABLE BLUE AND RED LED

2011 ◽  
Vol 04 (01) ◽  
pp. 45-52 ◽  
Author(s):  
GUANGDA LIU ◽  
CHANGE PAN ◽  
KAI LI ◽  
YUAN TAN ◽  
XUNBIN WEI
Keyword(s):  
Side Effects ◽  
Light Emitting Diode ◽  
Acne Vulgaris ◽  
Red Light ◽  
Light Sources ◽  
Light Emitting ◽  
Led Light ◽  
Led Phototherapy ◽  
Red Led ◽  
Complete Treatment

In this paper, we studied portable blue and red light-emitting-diode (LED) light sources in phototherapy for mild to moderate acne vulgaris to evaluate the efficacy and tolerance of patients. Patients, randomly divided into blue and red groups, received either blue or red LED phototherapy twice a week for four weeks. After complete treatment, the number of lesions reduced by 71.4% in the blue group, in contrast to 19.5% in the red group. No obvious side effects were observed during and one month after the treatment, except for some mild dryness mentioned by several patients.

scholarly journals Effect of different light sources on degree of conversion, hardness and plasticization of a composite

2013 ◽  
Vol 1 (2) ◽  
pp. 134
Author(s):  
Bruno de Castro Ferreira Barreto ◽  
Anderson Catelan ◽  
Ricardo Coelho Okida ◽  
Gisele Fernanda Gonçalves ◽  
Gisele Rodrigues da Silva ◽  
...  
Keyword(s):  
Clinical Performance ◽  
Light Emitting Diode ◽  
Knoop Hardness ◽  
Composite Resins ◽  
Degree Of Conversion ◽  
Light Sources ◽  
Light Emitting ◽  
Quartz Tungsten Halogen ◽  
Light Curing ◽  
Ft Ir

Clinical performance of composite resins depends largely on their mechanical properties, and those are influenced by several factors, such as the light-curing mode. The purpose of this study was to evaluate the influence of different light sources on degree of conversion (DC), Knoop hardness (KHN) and plasticization (P) of a composite resin. Disc-shaped specimens (5 x 2 mm) of Esthet-X (Dentsply) methacrylate-based microhybrid composite were light-cured using quartz-tungsten-halogen (QTH) Optilight Plus (Gnatus) or light-emitting diode (LED) Ultraled (Dabi Atlante) curing units at 400 and 340 mW/cm2 of irradiance, respectively. After 24 h, absorption spectra of composite were obtained using Nexus 670 (Nicolet) FT-IR spectrometer in order to calculate the DC. The KHN was measured in the HMV-2000 (Shimadzu) microhardness tester under 50 g loads for 15 s, and P was evaluated by percentage reduction of hardness after 24 h of alcohol storage. Data were subjected to t-Student test (alpha = 0.05). QTH device showed lower P and higher KHN than LED (p < 0.05), and no difference between the light-curing units was found for DC (p > 0.05). The halogen-curing unit with higher irradiance promoted higher KHN and lower softening in alcohol than LED.

scholarly journals Effects of High-Intensity Curing Lights on Microleakage under Bonded Lingual Retainers

2008 ◽  
Vol 78 (6) ◽  
pp. 1084-1088 ◽  
Author(s):  
Asli Baysal ◽  
Tancan Uysal ◽  
Mustafa Ulker ◽  
Serdar Usumez
Keyword(s):  
High Intensity ◽  
Light Emitting Diode ◽  
Light Sources ◽  
Composite Wire ◽  
Mandibular Incisor ◽  
Light Emitting ◽  
Halogen Light ◽  
Significant Difference ◽  
Light Curing ◽  
High Intensity Light

Abstract Objective: To evaluate the effects of high-intensity light curing units (light-emitting diode [LED] and plasma arc curing [PAC]) on the microleakage of flexible spiral wire retainers (FSWRs) at the composite/enamel and composite/wire interfaces. Materials and Methods: Forty-five human mandibular incisor teeth were separated into three groups of 15 teeth. Multistranded PentaOne wire of .0215 inch diameter was bonded to enamel and was cured with three different light curing units: a quartz-tungsten-halogen (QTH) unit and two high-intensity units (ie, LED and PAC). A conventional halogen light served as the control. Samples were sealed with nail varnish, stained with 0.5% basic fuchsine, and sectioned. Transverse sections were evaluated under a stereomicroscope and were scored for microleakage for the composite/enamel and composite/wire interfaces. Statistical analysis was performed by Kruskal-Wallis and Mann-Whitney U-tests with Bonferroni correction. Results: Little or no microleakage was detected at the composite/enamel interface of the FSWR cured with three different light sources. However, at the composite/wire interface, statistically significant differences were found between the QTH (mean, 1.10 ± 1.05 mm) and high-intensity curing units. The PAC resulted in the greatest amount of microleakage (mean, 2.63 ± 1.49 mm), whereas no statistically significant difference was noted between the PAC and the LED (mean, 2.35 ± 1.28 mm). Conclusion: High-intensity light curing units show statistically significant microleakage at the composite/wire interface and therefore may not be safe for use in bonding FSWRs.

A novel Cr3+-doped Lu2CaMg2Si3O12 garnet phosphor with broadband emission for near-infrared applications

2021 ◽  
Author(s):  
Wendong Nie ◽  
Liqin Yao ◽  
Guang Chen ◽  
Shihao Wu ◽  
Zhijian Liao ◽  
...  
Keyword(s):  
Plant Growth ◽  
Environmental Science ◽  
Near Infrared ◽  
Light Emitting Diode ◽  
Light Sources ◽  
Light Emitting ◽  
Broad Application ◽  
Led Light ◽  
Broadband Emission ◽  
Application Prospects

The near-infrared (NIR) phosphor-converted light emitting diode (pc-LED) light sources have broad application prospects in environmental science, biomedical and plant growth fields. However, NIR phosphor still suffers from narrowband emission...

Sign in / Sign up

Export Citation Format

Share Document