Evolution of Passivity for the Multi-Principal Element Alloy CoCrFeNi with Potential, pH and Exposure in Chloride Solution

CORROSION ◽  
10.5006/3902 ◽  
2021 ◽  
Author(s):  
Sanjay Choudhary ◽  
Nick Birbilis ◽  
Sebastian Thomas
Keyword(s):  
Passive Film ◽  
Photoelectron Spectroscopy ◽  
Exposure Duration ◽  
Electrochemical Impedance ◽  
Spectroscopy Analysis ◽  
Defect Model ◽  
Principal Element ◽  
Point Defect Model ◽  
X Ray ◽  
Resistance Increase

The evolution of passivity of the multi-principal element alloy CoCrFeNi was studied as a function of potential, pH and exposure duration in 0.1 M NaCl. It was shown that CoCrFeNi exhibits excellent passivity irrespective of pH, revealing a multi-oxide passive film enriched with Cr(III) oxide. Electrochemical impedance spectroscopy suggests that the passive film thickness and polarisation resistance increase with pH and exposure duration, whereby the growth behavior of the passive film was consistent with the assumptions of the point defect model. X-ray photoelectron spectroscopy analysis suggested that the fraction of Co(II) and Ni(II) oxides in the passive film, and their contributions to the passivity of the alloy, increased with increase in pH of the electrolyte. The present work explores the complex synergy between composition, thermodynamics and kinetics on the resultant passivity of a multi-principal element alloy.

scholarly journals Effect of Heat Treatment of Martensitic Stainless Steel on Passive Layer Growth Kinetics Studied by Electrochemical Impedance Spectroscopy in Conjunction with the Point Defect Model

2020 ◽  
Vol 1 (1) ◽  
pp. 77-91 ◽  
Author(s):  
Ingmar Bösing ◽  
Georg Marquardt ◽  
Jorg Thöming
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Passive Film ◽  
Growth Kinetics ◽  
Martensitic Stainless Steel ◽  
Electrochemical Impedance ◽  
Defect Model ◽  
Point Defect Model

Martensitic stainless steels are widely used materials. Their mechanical and corrosion properties are strongly influenced by their microstructure and thereby can be affected by heat treatment. In the present study, the effect of different austenitizing temperatures on the passive film growth kinetics of martensitic stainless steel is studied by electrochemical impedance spectroscopy. The data was further fitted by the point defect model to determine kinetic parameters. We show that an increasing austenitizing temperature leads to a more protective passive film and slows down passive film dissolution in sulfuric acid.

Ternary Composite of Molybdenum Disulfide-Graphene Oxide-Polyaniline for Supercapacitor

2021 ◽  
Author(s):  
Ke Qu ◽  
Yuqi Bai ◽  
Miao Deng
Keyword(s):  
Graphene Oxide ◽  
Molybdenum Disulfide ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Light Emitting Diode ◽  
Rate Capability ◽  
Energy Storage And Conversion ◽  
Carbon Paper ◽  
Power Sources ◽  
X Ray

Abstract The ever-increasing need for small and lightweight power sources for use in portable or wearable electronic devices has spurred the development of supercapacitors as a promising energy storage and conversion system. In this work, a simple, facile and easy-to-practice method has been developed to employ carbon paper (CP) as the support to coat molybdenum disulfide (MoS2) and graphene oxide (GO), followed by electrodeposition of polyaniline (PANI) to render CP/MoS2-GO-PANI. The preparation parameters, such as amounts of MoS2, GO and number of aniline electropolymerization cycles, have been optimized to render CP/MoS2-GO-PANI the best capacitive performance. The as-prepared optimal CP/MoS2-GO-PANI is characterized by X-ray powder diffraction, scanning electron microscopy, energy-dispersive spectroscopy, and X-ray photoelectron spectroscopy. The supercapacitive properties of CP/MoS2-GO-PANI as an electrode have been evaluated electrochemically via cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy testing. CP/MoS2-GO-PANI delivers a specific capacitance of 255.1 F/g at 1.0 A/g and exhibits excellent rate capability under larger current densities. Moreover, a symmetrical supercapacitor is assembled and three are connected in series to power a light-emitting diode for ~15 minutes, demonstrating the promising application potential of CP/MoS2-GO-PANI-based supercapacitor.

scholarly journals Organosilane-functionalization of nanostructured indium tin oxide films

2016 ◽  
Vol 6 (6) ◽  
pp. 20160056 ◽  
Author(s):  
R. Pruna ◽  
F. Palacio ◽  
M. Martínez ◽  
O. Blázquez ◽  
S. Hernández ◽  
...  
Keyword(s):  
Surface Area ◽  
Indium Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Annealing Treatment ◽  
Electrochemical Analysis ◽  
Cyclic Voltammograms ◽  
X Ray ◽  
Chip Technology ◽  
Significant Difference

Fabrication and organosilane-functionalization and characterization of nanostructured ITO electrodes are reported. Nanostructured ITO electrodes were obtained by electron beam evaporation, and a subsequent annealing treatment was selectively performed to modify their crystalline state. An increase in geometrical surface area in comparison with thin-film electrodes area was observed by atomic force microscopy, implying higher electroactive surface area for nanostructured ITO electrodes and thus higher detection levels. To investigate the increase in detectability, chemical organosilane-functionalization of nanostructured ITO electrodes was performed. The formation of 3-glycidoxypropyltrimethoxysilane (GOPTS) layers was detected by X-ray photoelectron spectroscopy. As an indirect method to confirm the presence of organosilane molecules on the ITO substrates, cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were also carried out. Cyclic voltammograms of functionalized ITO electrodes presented lower reduction-oxidation peak currents compared with non-functionalized ITO electrodes. These results demonstrate the presence of the epoxysilane coating on the ITO surface. EIS showed that organosilane-functionalized electrodes present higher polarization resistance, acting as an electronic barrier for the electron transfer between the conductive solution and the ITO electrode. The results of these electrochemical measurements, together with the significant difference in the X-ray spectra between bare ITO and organosilane-functionalized ITO substrates, may point to a new exploitable oxide-based nanostructured material for biosensing applications. As a first step towards sensing, rapid functionalization of such substrates and their application to electrochemical analysis is tested in this work. Interestingly, oxide-based materials are highly integrable with the silicon chip technology, which would permit the easy adaptation of such sensors into lab-on-a-chip configurations, providing benefits such as reduced size and weight to facilitate on-chip integration, and leading to low-cost mass production of microanalysis systems.

SiO2 films as heat resistant layers for protection of expandable polystyrene foam from flame torch–induced heat

2017 ◽  
Vol 31 (5) ◽  
pp. 657-667 ◽  
Author(s):  
S Varnagiris ◽  
S Tuckute ◽  
M Lelis ◽  
D Milcius
Keyword(s):  
Heat Resistance ◽  
Photoelectron Spectroscopy ◽  
Silicon Oxide ◽  
Plasma Generator ◽  
Expanded Polystyrene ◽  
Spectroscopy Analysis ◽  
X Ray ◽  
Heat Resistant ◽  
Pulsed Dc ◽  
Gas Atmosphere

Currently, polymeric insulation materials are widely used for energy saving in buildings. Despite of all benefits, these materials are generally sensitive to heat and highly flammable. This work discusses possibility to improve heat resistance of expanded polystyrene (EPS) foam using thin silicon dioxide (SiO2) films deposited by magnetron sputtering technique. In order to increase surface energy and adherence of SiO2 thin films to substrate EPS was plasma pretreated before films’ depositions using pulsed DC plasma generator for 40 s in argon gas. SiO2 formation was done in reactive argon and oxygen gas atmosphere. Laboratory made equipment was used for flame torch–induced heat resistance experiments. Results showed that silicon oxide films remains stable during heat resistance experiments up to 5 s and fully protects polystyrene (PS) substrate. Films are relatively stable for 30 s and 60 s and partially protect PS from melting and ignition. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy analysis confirmed that SiO2 layer, which is distributed uniformly on the EPS surface, could work as a good heat resistant material.

Effect of Sodium Metabisulfite on Selective Flotation of Chalcopyrite and Molybdenite

Minerals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1377
Author(s):  
Yuki Semoto ◽  
Gde Pandhe Wisnu Suyantara ◽  
Hajime Miki ◽  
Keiko Sasaki ◽  
Tsuyoshi Hirajima ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Separation Efficiency ◽  
Diesel Oil ◽  
Sodium Metabisulfite ◽  
Depressing Effect ◽  
Spectroscopy Analysis ◽  
X Ray ◽  
Selective Flotation

Sodium metabisulfite (MBS) was used in this study for selective flotation of chalcopyrite and molybdenite. Microflotation tests of single and mixed minerals were performed to assess the floatability of chalcopyrite and molybdenite. The results of microflotation of single minerals showed that MBS treatment significantly depressed the floatability of chalcopyrite and slightly reduced the floatability of molybdenite. The results of microflotation of mixed minerals demonstrated that the MBS treatment could be used as a selective chalcopyrite depressant in the selective flotation of chalcopyrite and molybdenite. Furthermore, the addition of diesel oil or kerosene could significantly improve the separation efficiency of selective flotation of chalcopyrite and molybdenite using MBS treatment. A mechanism based on X-ray photoelectron spectroscopy analysis results is proposed in this study to explain the selective depressing effect of MBS on the flotation of chalcopyrite and molybdenite.

scholarly journals Amorphous Ni x Co y P-supported TiO2 nanotube arrays as an efficient hydrogen evolution reaction electrocatalyst in acidic solution

2019 ◽  
Vol 10 ◽  
pp. 62-70 ◽  
Author(s):  
Yong Li ◽  
Peng Yang ◽  
Bin Wang ◽  
Zhongqing Liu
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Hydrogen Evolution ◽  
Hydrogen Evolution Reaction ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Nanotube Arrays ◽  
Active Surface Area ◽  
X Ray ◽  
Transmission Electron

Bimetallic phosphides have been attracting increasing attention due to their synergistic effect for improving the hydrogen evolution reaction as compared to monometallic phosphides. In this work, NiCoP modified hybrid electrodes were fabricated by a one-step electrodeposition process with TiO2 nanotube arrays (TNAs) as a carrier. X-ray diffraction, transmission electron microscopy, UV–vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy and scanning transmission electron microscopy/energy-dispersive X-ray spectroscopy were used to characterize the physiochemical properties of the samples. The electrochemical performance was investigated by cyclic voltammetry, linear sweep voltammetry, and electrochemical impedance spectroscopy. We show that after incorporating Co into Ni–P, the resulting Ni x Co y P/TNAs present enhanced electrocatalytic activity due to the improved electron transfer and increased electrochemically active surface area (ECSA). In 0.5 mol L−1 H2SO4 electrolyte, the Ni x Co y P/TNAs (x = 3.84, y = 0.78) demonstrated an ECSA value of 52.1 mF cm−2, which is 3.8 times that of Ni–P/TNAs (13.7 mF cm−2). In a two-electrode system with a Pt sheet as the anode, the Ni x Co y P/TNAs presented a bath voltage of 1.92 V at 100 mA cm−2, which is an improvment of 79% over that of 1.07 V at 10 mA cm−2.

Surface Analysis, Microstructural Characterization and Local Corrosion Processes in Decarburized SAE 9254 Spring Steel

CORROSION ◽  
10.5006/3234 ◽  
2019 ◽  
Vol 75 (12) ◽  
pp. 1474-1486
Author(s):  
Jéssica Cristina Costa de Castro Santana ◽  
Rejane Maria Pereira da Silva ◽  
Renato Altobelli Antunes ◽  
Sydney Ferreira Santos
Keyword(s):  
Surface Chemistry ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Microstructural Characterization ◽  
Spring Steel ◽  
Laser Scanning Microscopy ◽  
Local Corrosion ◽  
Confocal Laser ◽  
X Ray ◽  
Decarburized Layer

The aim of the present work was to study the surface chemistry, microstructure, and local corrosion processes at the decarburized layer of the SAE 9254 automotive spring steel. The samples were austenitized at 850°C and 900°C, and oil quenched. The microstructure was investigated using confocal laser scanning microscopy and scanning electron microscopy. The surface chemistry was analyzed by x-ray photoelectron spectroscopy. Electrochemical impedance spectroscopy and potentiodynamic polarization were used to assess the global corrosion behavior of the decarburized samples. Scanning electrochemical microscopy was used to evaluate the influence of decarburization on the local corrosion activity. Microstructural characterization and x-ray photoelectron spectroscopy analysis indicate a dependence of the local electrochemical processes with the steel microconstituents and Si oxides in the decarburized layer.

Sign in / Sign up

Export Citation Format

Share Document