Fluid inclusion hardening: Nanoscale evidence from naturally deformed pyrite

Author(s):  
Anna Rogowitz ◽  
Renelle Dubosq ◽  
David Schneider ◽  
Kevin Schweinar ◽  
Baptiste Gault

<p>The interaction of trace elements, fluids and crystal defects plays a vital role in a crystalline material’s response to an applied stress. For example, dislocations can be arrested by the strain field of immobile defects (i.e., particles or precipitates) or by the accumulation of mobile solutes in their cores, which can lead to strain hardening. The rheology of minerals is also strongly influenced by interactions with fluids, which are typically known to facilitate ductile deformation in geomaterials (i.e., hydrolytic weakening, dissolution creep). Investigation of these nanometer scale processes however, requires a correlative approach combining high-spatial resolution analytical techniques. In recent years, increasing developments in microscopy and microanalysis have allowed for the compositional measurements and spatial imaging of materials at the near-atomic scale. Herein, we have combined electron backscatter diffraction (EBSD) mapping, electron channeling contrast imaging (ECCI), scanning transmission electron microscopy (STEM) and atom probe tomography (APT) on a naturally deformed polycrystalline pyrite aggregate from the Abitibi Subprovince in Canada to investigate the role of fluid inclusions on mineral rheology. The combined EBSD and ECCI data reveal minor crystal misorientation and low-angle grain boundary development in the vicinity and at the tip of microfractures indicating a dominantly brittle regime with minor strain accommodation via crystal-plasticity where dislocations are mostly emitted by the propagating fracture. These interpretations are consistent with the peak temperature conditions of the sample estimated at 302 ± 27°C, which falls within the lower range of the brittle to crystal-plastic behaviour of pyrite (260–450°C). Nanoscale structural and chemical data reveal nanoscale fluid inclusions enriched in As, O, Na and K that are linked by As-enriched dislocations. Based on these results, we propose a model of fluid hardening whereby dislocations get pinned at fluid inclusions during crystal-plastic deformation, initiating pipe diffusion of trace elements from the fluid inclusions into dislocations that leads to their stabilization and local hardening. Although additional experiments are required on other mineral phases, our initial efforts advance the understanding of the interplay between nanostructures and impurities and its impact on the rheology of geomaterials during relatively low temperature deformation.</p><p> </p>

2020 ◽  
Author(s):  
Renelle Dubosq ◽  
Anna Rogowitz ◽  
Kevin Schweinar ◽  
Baptiste Gault ◽  
David Schneider

<p>In recent years, increasing developments in microscopy and microanalysis have allowed for the direct observation of nanoscale crystalline defects (i.e. dislocations). These defects are particularly important in naturally deformed materials yet this avenue of research remains understudied within the Earth Sciences. Dislocations can now be documented through the use of new and innovative structural and chemical analytical techniques such as electron channeling contrast imaging (ECCI), transmission electron microscopy, and atom probe tomography (APT). The presence and migration of dislocations in crystalline materials, including their role in trace element mobility, play a vital function in the way these materials respond to an applied stress. However, the mechanisms by which dislocations nucleate in minerals remain poorly understood. Prevailing models for dislocation nucleation include generation by Frank-Read sources, stress localization at crack-tips, atomic segregation, and free surface nucleation by critical stress-gradient criterion. Based on recent APT data from naturally-deformed pyrite, combined with electron backscatter diffraction (EBSD) mapping and ECC imaging, we propose a new nucleation mechanism where dislocations are generated by the local stress field in the vicinity of fluid inclusions. The investigated sample consists of a polycrystalline pyrite aggregate within a black shale host rock that has witnessed a peak temperature of 300°C. The combined EBSD and ECCI results reveal crystal plasticity in the form of lattice misorientation up to 8.5° and low-angle grain boundary development. APT data reveals nanoscale fluid inclusions enriched in As, O (H<sub>2</sub>O), Na and K as well as As- and Co-rich dislocations linked by fluid inclusions. This new model is the first documentation with APT methods of fluid inclusions (voids) in minerals, nanoscale features that are commonly misinterpreted as element clusters or chemically-enriched crystal-defects. The combined data has significant trans-disciplinary implications to the geosciences (structural geology, geochemistry, economic geology, geochronology), the material sciences (metals, ceramics, polymers), and analytical microscopy. Within geochronology voids and dislocations such as these in dated minerals may host elements or isotopes that negatively affect their age. Within ore deposit geology, voids in precious metal-hosting minerals may act as the necessary traps to structurally prevent the metals (gold, silver, copper) from migrating or diffusing out of the host mineral. In material sciences, the presence of such crystalline features can either limit or enhance the performance of engineering materials. Thus, performing APT analysis on crystalline material can help us better understand and predict their physical properties.</p>


Author(s):  
Vitória Régia P.R.O. Marciano ◽  
Francisco Javier Rios ◽  
Adriana B. Achtschin ◽  
José Marques Correia Neves ◽  
Darcy P. Svisero

Samples of beryls from three different pegmatite bodies, representative of the Santa Maria de Itabiraregion have been studied by several analytical techniques: Color, refraction, luminescence, density, IRspectrum, XRD, cell parameters, fluid inclusions and chemical composition have been considered. Theberyls have been analyzed for main elements as well as the following trace elements Na, Li, Cs, K, Rb, Ca,Ba, Zr. Fe e Ti.The pegmatites described in this paper are situated at the southeastern side of São Francisco Craton andbelong to the Eastern Pegmatite Province (PPO). They are related to a magmatism of Brasiliano age. Theyare being exploited for beryl and gems such as aquamarine, heliodor, colorless topaz and amazonite.The data are discussed and interpreted from the petrologic and metallogenetic point of view.


Minerals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 388 ◽  
Author(s):  
Max R. Verdugo-Ihl ◽  
Cristiana L. Ciobanu ◽  
Ashley Slattery ◽  
Nigel J. Cook ◽  
Kathy Ehrig ◽  
...  

Metal nanoparticles (NP) in minerals are an emerging field of research. Development of advanced analytical techniques such as Z-contrast imaging and mapping using high-angle annular dark field scanning transmission electron microscopy (HAADF STEM) allows unparalleled insights at the nanoscale. Moreover, the technique provides a link between micron-scale textures and chemical patterns if the sample is extracted in situ from a location of petrogenetic interest. Here we use HAADF STEM imaging and energy-dispersive X-ray spectrometry (EDX) mapping/spot analysis on focused ion beam prepared foils to characterise atypical Cu-As-zoned and weave-twinned hematite from the Olympic Dam deposit, South Australia. We aim to determine the role of solid-solution versus the presence of discrete included NPs in the observed zoning and to understand Cu-As-enrichment processes. Relative to the grain surface, the Cu-As bands extend in depth as (sub)vertical trails of opposite orientation, with Si-bearing hematite NP inclusions on one side and coarser cavities (up to hundreds of nm) on the other. The latter host Cu and Cu-As NPs, contain mappable K, Cl, and C, and display internal voids with rounded morphologies. Aside from STEM-EDX mapping, the agglomeration of native copper NPs was also assessed by high-resolution imaging. Collectively, such characteristics, corroborated with the geometrical outlines and negative crystal shapes of the cavities, infer that these are opened fluid inclusions with NPs attached to inclusion walls. Hematite along the trails features distinct nanoscale domains with lattice defects (twins, 2-fold superstructuring) relative to hematite outside the trails, indicating this is a nanoprecipitate formed during replacement processes, i.e., coupled dissolution and reprecipitation reactions (CDRR). Transient porosity intrinsically developed during CDRR can trap fluids and metals. Needle-shaped and platelet Cu-As NPs are also observed along (sub)horizontal bands along which Si, Al and K is traceable along the margins. The same signature is depicted along nm-wide planes crosscutting at 60° and offsetting (012)-twins in weave-twinned hematite. High-resolution imaging shows linear and planar defects, kink deformation along the twin planes, misorientation and lattice dilation around duplexes of Si-Al-K-planes. Such defects are evidence of strain, induced during fluid percolation along channels that become wider and host sericite platelets, as well as Cl-K-bearing inclusions, comparable with those from the Cu-As-zoned hematite, although without metal NPs. The Cu-As-bands mapped in hematite correspond to discrete NPs formed during interaction with fluids that changed in composition from alkali-silicic to Cl- and metal-bearing brines, and to fluid rates that evolved from slow infiltration to erratic inflow controlled by fault-valve mechanism pumping. This explains the presence of Cu-As NPs hosted either along Si-Al-K-planes (fluid supersaturation), or in fluid inclusions (phase separation during depressurisation) as well as the common signatures observed in hematite with variable degrees of fluid-mineral interaction. The invoked fluids are typical of hydrolytic alteration and the fluid pumping mechanism is feasible via fault (re)activation. Using a nanoscale approach, we show that fluid-mineral interaction can be fingerprinted at the (atomic) scale at which element exchange occurs.


2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Byeong-Gyu Chae ◽  
Seong Yong Park ◽  
Jay Hyok Song ◽  
Eunha Lee ◽  
Woo Sung Jeon

AbstractTo improve the performance of Li-ion batteries (LIBs), it is essential to understand the behaviour of Li ions during charge–discharge cycling. However, the analytical techniques for observing the Li ions are limited. Here, we present the complementary use of scanning transmission electron microscopy and atom probe tomography at identical locations to demonstrate that the evolution of the local Li composition and the corresponding structural changes at the atomic scale cause the capacity degradation of Li(Ni0.80Co0.15Mn0.05)O2 (NCM), an LIB cathode. Using these two techniques, we show that a Li concentration gradient evolves during cycling, and the depth of the gradient expands proportionally with the number of cycles. We further suggest that the capacity to accommodate Li ions is determined by the degree of structural disordering. Our findings provide direct evidence of the behaviour of Li ions during cycling and thus the origin of the capacity decay in LIBs.


2020 ◽  
Author(s):  
Desmond Moser

<p>The earliest known physical records of Mars and Earth lie in microscopic grains of zirconium-rich geochronology minerals such as zircon and baddeleyite. The reconstruction of the pressure and temperature histories of these phases is one of the few ways in which we can bracket the onset of conditions permissive of microbiota survival, and requires an integration of several nanoscale measurement techniques. This presentation will overview a recent, detailed investigation of zircons and baddeleyite from Mars [1], the earliest known from planets to date, as well as comparator studies of thermally and/or shock metamorphosed samples from the Earth and Moon. The approach is to spatially correlate measurements of the chemical and orientation microstructure of individual grains in order to characterize thermal, shock and diffusion history and better interpret U-Pb geochronology data. Also revealed are proxies for high temperature metamorphism such as nanoclusters of Pb and trace elements and nanoveins of impact melt as well as trace elements introduced through subsequent lower-temperature hydrothermal metamorphism. The techniques required include electron microscopy and cathodoluminescence (CL), Electron Backscatter Diffraction (EBSD), Transmission Kikuchi diffraction (TKD), mass spectrometry, and Atom Probe Tomography (APT). The Mars records were collected from a population of zircon and baddeleyite grains within five meteoritic fragments of polymict breccia (e.g. NWA 7034, NWA 7475). These data were compared to those from analogue sites of heavily bombarded Archean crust such as the central uplift of the Vredefort structure of South Africa, the Earth’s largest and oldest recognized impact crater, the Sudbury impact structure in Canada, and Apollo samples of the lunar regolith. The Mars population of grains reveals little evidence of the nanofeatures of heavily bombarded and heated crust, and no exposure to life-limiting pressures or temperature since crystallization 4.48 billion years ago. The conclusion is that global, planet-shaping bombardment effects on Mars, such as those which created its distinctive hemispheric dichotomy, had ceased by the time these grains and their associated crust crystallized. It follows that Mars entered a window of habitable conditions very early in solar system history, a pathway likely mirrored by the Earth. In this way nanoscale measurements, required to investigate microscopic mineral grains, serve as important tools for reconstructing important time periods in planetary evolution and abiogenesis.</p><p>Reference:</p><p>[1] DE Moser, GA Arcuri, DA Reinhard, LF White, JR Darling, IR Barker, DJ Larson, AJ Irving, FM McCubbin, KT Tait, J Roszjar, A Wittmann, C Davis (<strong>2019</strong>) Decline of giant impacts on Mars by 4.48 billion years ago and an early opportunity for habitability. <strong><em>Nature Geoscience </em></strong>12,  522–527.</p>


2014 ◽  
Vol 783-786 ◽  
pp. 755-760 ◽  
Author(s):  
Iván Gutierrez-Urrutia ◽  
Ross Marceau ◽  
Michael Herbig ◽  
Dierk Raabe

We have investigated the strain-hardening mechanisms across the relevant scales in a Fe-22Mn-0.6C (wt.%) twinning induced plasticity steel by multi-scale microstructure characterization. The approach makes use of electron microscopy techniques such as electron channeling contrast imaging (ECCI) to characterize microstructure features at the micro/nanoscale, and atomic-scale investigations of partitioning behavior across interfaces and solid solution/clustering effects by atom probe tomography (APT). The contribution of most relevant microstructure features to strain hardening is analyzed.


2013 ◽  
Vol 19 (6) ◽  
pp. 1581-1585 ◽  
Author(s):  
Ross K.W. Marceau ◽  
Ivan Gutierrez-Urrutia ◽  
Michael Herbig ◽  
Katie L. Moore ◽  
Sergio Lozano-Perez ◽  
...  

AbstractA multi-scale investigation of twin bundles in Fe–22Mn–0.6C (wt%) twinning-induced plasticity steel after tensile deformation has been carried out by truly correlative means; using electron channelling contrast imaging combined with electron backscatter diffraction, high-resolution secondary ion mass spectrometry, scanning transmission electron microscopy, and atom probe tomography on the exact same region of interest in the sample. It was revealed that there was no significant segregation of Mn or C to the twin boundary interfaces.


Author(s):  
M.P. Thomas ◽  
A.R. Waugh ◽  
M.J. Southon ◽  
Brian Ralph

It is well known that ion-induced sputtering from numerous multicomponent targets results in marked changes in surface composition (1). Preferential removal of one component results in surface enrichment in the less easily removed species. In this investigation, a time-of-flight atom-probe field-ion microscope A.P. together with X-ray photoelectron spectroscopy XPS have been used to monitor alterations in surface composition of Ni3Al single crystals under argon ion bombardment. The A.P. has been chosen for this investigation because of its ability using field evaporation to depth profile through a sputtered surface without the need for further ion sputtering. Incident ion energy and ion dose have been selected to reflect conditions widely used in surface analytical techniques for cleaning and depth-profiling of samples, typically 3keV and 1018 - 1020 ion m-2.


2018 ◽  
Author(s):  
Zoltán Kis ◽  
Katalin Gméling ◽  
Tímea Kocsis ◽  
János Osán ◽  
Mihály András Pocsai ◽  
...  

We present precise analysis of major and trace elements of the humic acid. We used three different element analytical techniques in our investigations as prompt-gamma activation analysis (PGAA), neutron activation analysis (NAA) and X-ray fluorescence (XRF) analysis was carried out. We identified 42 elements in our sample.


2019 ◽  
Author(s):  
Aurelio A. Rossinelli ◽  
Henar Rojo ◽  
Aniket S. Mule ◽  
Marianne Aellen ◽  
Ario Cocina ◽  
...  

<div>Colloidal semiconductor nanoplatelets exhibit exceptionally narrow photoluminescence spectra. This occurs because samples can be synthesized in which all nanoplatelets share the same atomic-scale thickness. As this dimension sets the emission wavelength, inhomogeneous linewidth broadening due to size variation, which is always present in samples of quasi-spherical nanocrystals (quantum dots), is essentially eliminated. Nanoplatelets thus offer improved, spectrally pure emitters for various applications. Unfortunately, due to their non-equilibrium shape, nanoplatelets also suffer from low photo-, chemical, and thermal stability, which limits their use. Moreover, their poor stability hampers the development of efficient synthesis protocols for adding high-quality protective inorganic shells, which are well known to improve the performance of quantum dots. <br></div><div>Herein, we report a general synthesis approach to highly emissive and stable core/shell nanoplatelets with various shell compositions, including CdSe/ZnS, CdSe/CdS/ZnS, CdSe/Cd<sub>x</sub>Zn<sub>1–x</sub>S, and CdSe/ZnSe. Motivated by previous work on quantum dots, we find that slow, high-temperature growth of shells containing a compositional gradient reduces strain-induced crystal defects and minimizes the emission linewidth while maintaining good surface passivation and nanocrystal uniformity. Indeed, our best core/shell nanoplatelets (CdSe/Cd<sub>x</sub>Zn<sub>1–x</sub>S) show photoluminescence quantum yields of 90% with linewidths as low as 56 meV (19.5 nm at 655 nm). To confirm the high quality of our different core/shell nanoplatelets for a specific application, we demonstrate their use as gain media in low-threshold ring lasers. More generally, the ability of our synthesis protocol to engineer high-quality shells can help further improve nanoplatelets for optoelectronic devices.</div>


Sign in / Sign up

Export Citation Format

Share Document