scholarly journals ALDEHYDE EMISSIONS FROM A STATIONARY DIESEL ENGINE OPERATING WITH CASTOR OIL BIODIESEL – DIESEL OIL BLENDS

2010 ◽  
Vol 9 (1-2) ◽  
pp. 35 ◽  
Author(s):  
P. B. Zarante ◽  
M. J. Da Silva ◽  
O. S. Valente ◽  
J. R. Sodré
Keyword(s):  
Diesel Engine ◽  
Castor Oil ◽  
Direct Injection ◽  
Diesel Oil ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Oil Blends ◽  
Fuel Blends ◽  
Flame Ionization

The presence of aldehyde in the exhaust gas of a stationary, direct injection, compression ignition engine operating with castor oil biodiesel/diesel oil blends (B5, B10, B20 and B35) is analyzed. The diesel engine was operated with constant speed of 1800 rev/min and load of 37.5 kW. The gas sample was collected directly from the exhaust. Aldehydes were identified and quantified using gas chromatography (GC) with flame ionization detector analyzer (FID). Acetaldehyde presented higher exhaust concentration than formaldehyde for all fuel blends tested. In general, the exhaust aldehyde levels were very low and did not present significant differences between the fuel blends tested.

Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

Performance and Emission Evaluation of a Diesel Engine Fuelled with Cashew Nut Shell Oil Blends

2014 ◽  
Vol 984-985 ◽  
pp. 893-899 ◽  
Author(s):  
S. Santhanakrishnan ◽  
S. Jose
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Experimental Tests ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Oil Blends ◽  
Cashew Nut ◽  
Cashew Nut Shell

This paper presents the properties and application of cashew nut shell oil as blend component for diesel in compression ignition engine. Experimental tests were carried out in a single cylinder, four stroke, direct injection, compression ignition engine fueled with cashew nut shell oil blends. During the experiments, the performance and emission characteristics of the diesel engine was analyzed and compared with the neat diesel fuel performance.

scholarly journals Emission Characteristics under Diesel and Biodiesel Fueled Compression Ignition Engine with Various Injector Holes and EGR Conditions

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2973
Author(s):  
Taejung Kim ◽  
Jungsoo Park ◽  
Honghyun Cho
Keyword(s):  
Diesel Engine ◽  
Environmental Pollutants ◽  
Exhaust Gas Recirculation ◽  
Emission Characteristics ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Fuel Type ◽  
Compression Ignition Engine ◽  
Conventional Rail ◽  
Gas Recirculation

The combustion performance of a conventional rail diesel engine was investigated by measuring the exhaust gas with the respect to the number of injector holes, fuel type, and the use of exhaust gas recirculation (EGR), to provide a detailed reduction of environmental pollutants. It was found that a six- or seven-hole injector was more effective than a five-hole injector for reducing the exhaust gas. In addition, the mixing of 20% biodiesel oil with diesel most effectively reduced the HC and NOx contents. The technology generally reduced the NOx and CO contents of the exhaust, but had no significant effect on the HC and CO2 contents.

Experimental Investigation of the Effect of Exhaust Gas Recirculation on Lubricating Oil Degradation and Wear of a Compression Ignition Engine

2005 ◽  
Vol 128 (4) ◽  
pp. 921-927 ◽  
Author(s):  
Shrawan Kumar Singh ◽  
Avinash Kumar Agarwal ◽  
Dhananjay Kumar Srivastava ◽  
Mukesh Sharma
Keyword(s):  
Experimental Investigation ◽  
Direct Injection ◽  
Exhaust Gas Recirculation ◽  
Lubricating Oil ◽  
Exhaust Gas ◽  
Scanning Electron Micrographs ◽  
Compression Ignition ◽  
Piston Rings ◽  
Compression Ignition Engine ◽  
Gas Recirculation

This experimental investigation was aimed to investigate the effect of exhaust gas recirculation (EGR) on wear of in-cylinder engine parts. EGR setup was prepared for a two-cylinder, air-cooled, constant-speed direct-injection compression-ignition engine. Test setup was run for 96hr under predetermined loading cycles in two phases; normally, operating condition (i.e., without EGR) and with a fixed EGR rate of 25%. Addition of metallic wear debris in the lubricating oil samples drawn after regular interval from both engine operating phases was investigated. Relatively higher concentrations of all wear metals were found in the lubricating oil of the EGR-operated engine, which indicates higher wear of various engine parts. Weight loss of piston rings used in both phases was compared to quantify the amount of wear of piston rings. To quantify the amount of cylinder wear surface roughness parameters of cylinder liners were measured at three positions (top dead center, mid-stroke, and bottom dead center) on thrust and anti-thrust side. A qualitative analysis was also carried out by taking surface profiles and Scanning Electron Micrographs at same locations.

scholarly journals Combustion characteristics of compression ignition engine fuelled with rapeseed oil–diesel fuel–n-butanol blends

2021 ◽  
Vol 76 ◽  
pp. 17
Author(s):  
Jakub Čedík ◽  
Martin Pexa ◽  
Bohuslav Peterka ◽  
Miroslav Müller ◽  
Michal Holubek ◽  
...  
Keyword(s):  
Vegetable Oils ◽  
Diesel Fuel ◽  
Rapeseed Oil ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Solid Particles ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Fuel Blends

Liquid biofuels for compression ignition engines are often based on vegetable oils. In order to be used in compression ignition engine the vegetable oils have to be processed because of their high viscosity or it is also possible to use vegetable oils in fuel blends. In order to decrease the viscosity of the fuel blends containing crude vegetable oil the alcohol-based fuel admixtures can be used. The paper describes the effect of rapeseed oil–diesel fuel–n-butanol blends on combustion characteristics and solid particles production of turbocharged compression ignition engine. The 10% and 20% concentrations of n-butanol in the fuel blend were measured and analysed. The engine Zetor 1204, located in tractor Zetor Forterra 8641 with the power of 60kW and direct injection was used for the measurement. The engine was loaded through power take off shaft of the tractor using mobile dynamometer MAHA ZW500. The measurement was carried out in stabilized conditions at 20%, 60% and 100% engine load. The engine speed was kept at 1950 rpm. Tested fuel blends showed lower production of solid particles than diesel fuel and lower peak cylinder pressure and with increasing concentration of n-butanol in the fuel blend the ignition delay was prolonged and premixed phase of combustion was increased.

scholarly journals Research on Performance And Emission on Compression Ignition Engine Fuelled With Blends of Neem Bio-Diesel

2019 ◽  
Vol 8 (6) ◽  
pp. 3732-3735
Keyword(s):  
Diesel Engine ◽  
Vegetable Oils ◽  
Castor Oil ◽  
Fossil Fuels ◽  
Emission Characteristics ◽  
Nox Emissions ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Performance And Emission

In this contemporary era it is mandatory to increasing the usage of non edible biodiesel to replace the fossil fuels. This non edible biodiesels are produced from vegetable oils which is clean burning and renewable. This paper deals with the performance and emission characteristics on diesel engine with blends of Castor oil as biodiesel. Castor oil biodiesel is prepared by the use of adding 1% v/v H2SO4 after the transesterification process. The engine tests were performed with various blends B20, B40, B60 on a single cylinder, 4-stroke, diesel engine. The result shows Higher performance and lower emissions for B20 than the diesel and other blends. The brake thermal efficiency is higher than the diesel and CO, HC and NOX emissions were 22%, 8.4%, and 21% lesser than that of diesel.

Experimental and Numerical Study on the Combustion Characteristics of a Premixed Charge Compression Ignition Engine

2002 ◽  
Author(s):  
Dae Sik Kim ◽  
Ki Hyung Lee ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Numerical Method ◽  
Numerical Study ◽  
Combustion Characteristics ◽  
Injection System ◽  
Emission Characteristics ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Mixing Ratio ◽  
Compression Ignition Engine

The objective of this work is to investigate the effect of premixed fuel ratio on the combustion and emission characteristics in diesel engine by the experimental and numerical method. In order to investigate the effect of various factors such as the mixing ratio, EGR rate, and engine load on the exhaust emissions from the premixed charge compression ignition diesel engine, the injection amount of premixed fuel is controlled by electronic port injection system. The range of mixing ratio between dual fuels used in this study is between 0 and 0.85, and the exhaust gas is recirclulated until 30 percent of EGR rate.

Operating Parameters of Catalysts With Catalytic Converter for Compression Ignition Engine

2005 ◽  
Author(s):  
P. V. Walke ◽  
N. V. Deshpande ◽  
L. P. Daddamwar
Keyword(s):  
Diesel Engine ◽  
Catalytic Converter ◽  
Circulation System ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Oxides Of Nitrogen ◽  
Test Rig ◽  
Compression Ignition Engine ◽  
Perforated Plates ◽  
Secondary Air

Testing of catalytic converter with exhaust gas re-circulation system for diesel engine to reduce pollute gases is chosen for present work. The emphasis is given on hydrocarbon (HC), carbon monoxide (CO) and oxides of nitrogen. The catalytic converter was developed with variations of catalyst plates. Perforated plates of copper and combination of copper oxide and cerium oxide (CeO2 +CuO) were used as the catalyst. Copper spacer was used in between plates to vary the distance. Secondary air was injected into the converter to aid oxidization of HC and CO. Experimental study was carried out on computerized kirloskar single cylinder four stroke (10 B.H.P, 7.4 KW) diesel engine test rig with an eddy current dynamometer. The converter was tested with various combination with exhaust gas re-circulation (EGR) system. There are some improvements in the reduction and conversion efficiency of HC & CO. Exhaust gas re-circulation has proved to be effective in reducing NOx.

Sign in / Sign up

Export Citation Format

Share Document