Study on Rajkoroi (Albizia richardiana) for Ply and Particleboard Manufacture

The suitability of Rajkoroi (Albizia richardiana) for plywood and particleboard manufacture has been determined. Study shows that 1.5mm thick smooth and figured veneer can be peeled and dried easily. Three-ply plywood were made using veneer of this species bonded with liquid urea formaldehyde glue of 50% solid content extended with wheat flour and catalyzed with 2% hardener (ammonium chloride) under the three specific pressures, such as 1.05 N/mm2,1.40 N/mm2, 1.76 N/mm2 in three replications at 6 minute press time and 120°C press temperature. Dry and wet shear test were conducted on the samples and their shear load at failure per unit area and percentage of wood failure were determined. 1.05 N/mm2 Pressure was found best for the manufacture. The particleboards of Rajkoroi (Albizia richardiana) were tested for determining the strength & dimensional stability. Tensile strength passed the German and British Standard Specification. Bending strength found to be nearest to the Bureau of Indian Standard but lower than German and British standard Specification.

Download Full-text

Peeling and Gluing Study of Khaya anthotheca for Ply and Particle Board

Indian Journal of Forestry ◽

10.54207/bsmps1000-2015-g62lzt ◽

2015 ◽

Vol 38 (2) ◽

pp. 113-116

Author(s):

Md. Rahaman ◽

Khurshid Akhter ◽

Md. Islam

Keyword(s):

Bending Strength ◽

Unit Area ◽

Urea Formaldehyde ◽

Physical And Mechanical Properties ◽

Solid Content ◽

Shear Load ◽

Particle Board ◽

British Standard ◽

Press Temperature ◽

Press Time

Logs of Khaya anthotheca wood has been studied for assessing the suitability of plywood and particleboard manufacture. It was found that 1.5 mm thick smooth and figured veneer can be made and dried easily. Three-ply plywood were made using veneer of this species bonded with liquid urea formaldehyde glue of 50% solid content extended with wheat flour and catalyzed (ammonium chloride) with 2% hardener under the specific pressures, viz, 1.05 N/mm2, 1.40 N/mm2, 1.76 N/mm2 in three replications at 6 minute press time and 120°C press temperature. Dry and wet shear test were conducted on the sample and their shear load at failure per unit area and percentage of wood failure were determined. 1.05 N/mm2 pressure for the manufacture of ply wood was found to be the best. The physical and mechanical properties of K.anthotheca particleboard were studied. The particleboards were tested for determining the strength and dimensional stability. The tensile strength (internal bond strength 0.68 N/mm2) passed the German and British standard specifications; bending strength (modules of rupture 11.25 N/mm2) passed the Indian Standard but did not pass the German and British standard specifications.

Download Full-text

Albizia richardiana King & Prain as a raw material for ply and particleboard

Journal of Non Timber Forest Products ◽

10.54207/bsmps2000-2015-9216i4 ◽

2015 ◽

Vol 22 (3) ◽

pp. 139-141

Author(s):

Md. Rahaman ◽

Khurshid Akhter ◽

S. Hossain ◽

Md. Islam

Keyword(s):

Bending Strength ◽

Urea Formaldehyde ◽

Physical And Mechanical Properties ◽

Solid Content ◽

Raw Material ◽

Standard Specification ◽

Press Temperature ◽

Albizia Richardiana ◽

German Standard ◽

Press Time

Woods of Albizia richardiana has been studied for assessing the suitability for plywood and particleboard manufacture. It was found that 1.5 mm thick smooth and figured veneer can be peeled and dried easily. Three-ply plywood were made using veneer of this species bonded with liquid urea formaldehyde glue of 50% solid content extended with wheat flour and catalyzed (ammonium chloride) with 2% hardener under the three specific pressures, viz,1.05 N/mm2, 1.40 N/mm2, 1.76 N/mm2 in three replications at 6 minute press time and 120°C press temperature. Dry and wet shear test were conducted on the sample and their shear load at failure per unit area and percentage of wood failure were determined. 1.05 N/mm2 pressure for the manufacture of plywood was found to be the best. The physical and mechanical properties of Albizia richardiana wood particleboard were studied. The particleboards were tested for determining the strength and dimensional stability. The tensile strength 0.56N/mm2 passed the British and German standard specification, bending strength (modulus of rupture10.80N/mm2) was found nearest to Indian Standard but low German and British standard specification.

Download Full-text

Suitability of Hybrid Acacia Wood for Manufacturing Plywood and Particleboard

Journal of Bangladesh Academy of Sciences ◽

10.3329/jbas.v36i2.12960 ◽

2012 ◽

Vol 36 (2) ◽

pp. 171-176 ◽

Cited By ~ 3

Author(s):

MM Rahaman ◽

K Akhter ◽

D Biswas ◽

MW Sheikh

Keyword(s):

Bending Strength ◽

Unit Area ◽

Urea Formaldehyde ◽

Acacia Mangium ◽

Solid Content ◽

Timber Species ◽

Press Temperature ◽

Natural Crossing ◽

Press Time ◽

Academy Of Sciences

Hybrid acacia, produced from natural crossing between two introduced timber species Acacia mangium and A. auriculiformies has been studied for assessing the suitability of plywood and particleboard manufacture. It was found that 1.5 mm thick smooth and figured veneer can be made and dried easily. Three-ply plywood were made using veneer of this species bonded with liquid urea formaldehyde glue of 50% solid content extended with wheat flower and catalyzed (ammonium chloride) with 2% hardener under the specific pressures, viz., 1.05, 1.40 and 1.76 N/mm2 in three replications at 6 minute press time and 120°C press temperature. Dry and wet shear test were conducted on the sample and their shear load at failure per unit area and percentage of wood failure were determined. 1.76 N/mm2 pressure for the manufacture of ply wood is found to be the best. The particleboard was tested for determining the strength and dimensional stability. The bending strength passed the standard specification, tensile strength was found to be low as per Indian standard. DOI: http://dx.doi.org/10.3329/jbas.v36i2.12960 Journal of Bangladesh Academy of Sciences, Vol. 36, No. 2, 171-176, 2012

Download Full-text

Characterization of Hoop Pine (Araucaria Cunninghamii Sweet) for Ply and Particleboard Manufacture

Indian Journal of Forestry ◽

10.54207/bsmps1000-2014-er2dc6 ◽

2014 ◽

Vol 37 (2) ◽

pp. 143-146

Author(s):

Md. Rahaman ◽

Khurshid Akhter ◽

M.W. Sheikh ◽

R. Akhter

Keyword(s):

Bending Strength ◽

Urea Formaldehyde ◽

Physical And Mechanical Properties ◽

Solid Content ◽

British Standard ◽

Press Temperature ◽

Hoop Pine ◽

Araucaria Cunninghamii ◽

Press Time

Studies for assessing the suitability of Hoop-pine (Araucaria cunninghamii) wood for plywood and particleboard manufacture. It was found that 1.5 mm thick smooth and figured veneer can be made and dried easily. Three-ply plywood were made using veneer of this species bonded with liquid urea formaldehyde glue of 50% solid content, extended with wheat flour and catalyzed (ammonium chloride) with 2% hardener under the specific pressures, viz, 1.05 N/mm2, 1.40 N/mm2, 1.76 N/mm2 in three replications at 6 minutes press time and 120°C press temperature. Dry and wet shear test were conducted on the sample and their shear load at failure per unit area and percentage of wood failure were determined. 1.40 N/mm2 pressure was found best for the manufacture of plywood. The physical and mechanical properties of hoop-pine particleboard were studied. The particleboards were tested for determining the strength and dimensional stability. The tensile strength passed the German and British standard specifications, bending strength found to nearest the Indian Standard but did not pass the German and British standard specifications.

Download Full-text

Study on Particleboard made from Nipa palm (Nypa fruticans) stem wood and Rajkoroi (Albizia richardiana) wood

Journal of Non Timber Forest Products ◽

10.54207/bsmps2000-2018-qpjp02 ◽

2018 ◽

Vol 25 (1) ◽

pp. 15-18

Author(s):

Md. Mahabubur Rahaman ◽

◽

Khurshid Akhter ◽

S. Hossain ◽

Md. Rakibul Islam ◽

...

Keyword(s):

Tensile Strength ◽

Dimensional Stability ◽

Bending Strength ◽

Strength Properties ◽

Wood Chips ◽

Standard Specification ◽

Stem Wood ◽

Nypa Fruticans ◽

Albizia Richardiana ◽

Nipa Palm

The study was conducted to find out the suitability of making particleboard using nipa palm (Nypa fruticans) stem wood and rajkoroi (Albizia richardiana) wood chips. Particleboards were fabricated at six different ratios of nipa palm stem and rajkoroi wood chips such as 100:0, 75:25, 50:50, 25:75, 10:90 and 0:100. Characteristics of particleboards such as modulus of rupture, internal bond strength, water absorption, thickness swelling and moisture content were measured. Results shows that particleboards made from 100% rajkoroi wood chips have the highest static bending properties and highest tensile strength properties of other particleboards but 100% nipa palm stem wood chips have the lowest static bending and lowest tensile strength properties of other particleboards. 10% nipa palm stem wood chips particleboard have the highest bending strength and tensile strength is better than 100% nipa palm stem wood chips and other mixing chips of particleboards. Mechanical, water resistance and dimensional stability properties were tested according to Indian standard specification. Tensile strength passed the British and German standard specification and nearest to Bureau of Indian Standard, bending strength was found nearest to Indian Standard but lower than German and British Standard specification. Strength property of rajkoroi wood chips particleboard is higher than nipa palm steam wood chips particleboard but dimensional stability is lower than nipa palm steam wood chips particleboard.

Download Full-text

Mechanical Properties and Free Formaldehyde Content of Particleboards Produced using Ammonium Sulphate-Based Hardener Partially Replaced with Tartaric Acid

Drvna industrija ◽

10.5552/drvind.2020.1950 ◽

2020 ◽

Vol 71 (4) ◽

pp. 389-393

Author(s):

Nikola Španić ◽

Vladimir Jambreković ◽

Jaroslav Kljak ◽

Goran Mihulja ◽

Željko Milanović

Keyword(s):

Mechanical Properties ◽

Tartaric Acid ◽

Ammonium Sulphate ◽

Bending Strength ◽

Urea Formaldehyde ◽

Production Costs ◽

Partial Replacement ◽

Formaldehyde Content ◽

Food Industries ◽

Press Time

The use of resins, whose curing reaction takes place by high temperature and hardener addition, is inevitably involved in particleboard manufacturing process. In addition to commercial hardeners, such as ammonium sulphate, with the aim of optimizing the production process and reducing the production costs, a certain percentage of hardener can, among other things, be replaced with price affordable bio-based materials. Tartaric acid, that is its salts (tartrates), which are commercially produced for the needs of wine and food industries, are a part of the aforementioned group of products. Since tartaric acid is a relatively inexpensive, readily available, weak diprotic and aldaric acid, the question arises whether it can be used as a component of the hardener system for curing urea-formaldehyde resins that are commercially used in particleboard production. For that reason, in this paper, the influence of partial replacement of ammonium sulphate hardener with tartaric acid on the mechanical properties (bending strength, modulus of elasticity and internal bond) and free formaldehyde content of experimentally produced particleboards was examined. Boards thickness, density and moisture content were also determined. The test results suggest that tartaric acid has a beneficial effect on the above particleboard properties, but they also indicate that the extent of that effect is strongly dependent on panel press time.

Download Full-text

Utilization of Birch Bark as an Eco-Friendly Filler in Urea-Formaldehyde Adhesives for Plywood Manufacturing

Polymers ◽

10.3390/polym13040511 ◽

2021 ◽

Vol 13 (4) ◽

pp. 511

Author(s):

Roman Réh ◽

Ľuboš Krišťák ◽

Ján Sedliačik ◽

Pavlo Bekhta ◽

Monika Božiková ◽

...

Keyword(s):

Bending Strength ◽

Urea Formaldehyde ◽

Formaldehyde Emission ◽

Birch Bark ◽

Gravimetric Analysis ◽

European Standard ◽

Scanning Calorimetry ◽

Wood Processing ◽

Fagus Sylvatica L ◽

Positive Effect

The potential of using ground birch (Betula verrucosa Ehrh.) bark as an eco-friendly additive in urea-formaldehyde (UF) adhesives for plywood manufacturing was investigated in this work. Five-ply plywood panels were fabricated in the laboratory from beech (Fagus sylvatica L.) veneers bonded with UF adhesive formulations comprising three addition levels of birch bark (BB) as a filler (10%, 15%, and 20%). Two UF resin formulations filled with 10% and 20% wheat flour (WF) were used as reference samples. The mechanical properties (bending strength, modulus of elasticity and shear strength) of the laboratory-fabricated plywood panels, bonded with the addition of BB in the adhesive mixture, were evaluated and compared with the European standard requirements (EN 310 and EN 314-2). The mechanical strength of the plywood with the addition of BB in the adhesive mixture is acceptable and met the European standard requirements. Markedly, the positive effect of BB in the UF adhesive mixture on the reduction of formaldehyde emission from plywood panels was also confirmed. Initially, the most significant decrease in formaldehyde release (up to 14%) was measured for the plywood sample, produced with 15% BB. After four weeks, the decrease in formaldehyde was estimated up to 51% for the sample manufactured with 20% BB. The performed differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), and derivative thermogravimetry (DTG), also confirmed the findings of the study. As this research demonstrated, BB as a waste or by-product of wood processing industry, can be efficiently utilized as an environmentally friendly, inexpensive alternative to WF as a filler in UF adhesive formulations for plywood manufacturing.

Download Full-text

Eco-Friendly, High-Density Fiberboards Bonded with Urea-Formaldehyde and Ammonium Lignosulfonate

Polymers ◽

10.3390/polym13020220 ◽

2021 ◽

Vol 13 (2) ◽

pp. 220

Author(s):

Petar Antov ◽

Viktor Savov ◽

Ľuboš Krišťák ◽

Roman Réh ◽

George I. Mantanis

Keyword(s):

Mechanical Properties ◽

Bending Strength ◽

Urea Formaldehyde ◽

Physical And Mechanical Properties ◽

High Density ◽

Thickness Swelling ◽

Formaldehyde Content ◽

Uf Resin ◽

Natural Wood ◽

European Standards

The potential of producing eco-friendly, formaldehyde-free, high-density fiberboard (HDF) panels from hardwood fibers bonded with urea-formaldehyde (UF) resin and a novel ammonium lignosulfonate (ALS) is investigated in this paper. HDF panels were fabricated in the laboratory by applying a very low UF gluing factor (3%) and ALS content varying from 6% to 10% (based on the dry fibers). The physical and mechanical properties of the fiberboards, such as water absorption (WA), thickness swelling (TS), modulus of elasticity (MOE), bending strength (MOR), internal bond strength (IB), as well as formaldehyde content, were determined in accordance with the corresponding European standards. Overall, the HDF panels exhibited very satisfactory physical and mechanical properties, fully complying with the standard requirements of HDF for use in load-bearing applications in humid conditions. Markedly, the formaldehyde content of the laboratory fabricated panels was extremely low, ranging between 0.7–1.0 mg/100 g, which is, in fact, equivalent to the formaldehyde release of natural wood.

Download Full-text

KUALITAS PAPAN PARTIKEL BERDASARKAN KOMPOSISI SEKAM PADI DAN KAYU SENGON DENGAN VARIASI KADAR PEREKAT

JURNAL HUTAN LESTARI ◽

10.26418/jhl.v7i2.33693 ◽

2019 ◽

Vol 7 (2) ◽

Author(s):

Dendi Prayoga ◽

. Dirhamsyah ◽

. Nurhaida

Keyword(s):

Mechanical Properties ◽

Moisture Content ◽

Rice Husk ◽

Raw Materials ◽

Urea Formaldehyde ◽

Physical And Mechanical Properties ◽

Solid Content ◽

Particle Board ◽

Rice Husks ◽

Wood Processing

This research aimed to examine the physical and mechanical properties of particle boards based on the composition of raw materials and adhesive content and know the treatment of the composition of raw materials and the best adhesive content and meet the standard JIS A 5908-2003. The research was conducted at Wood Workshop Laboratory, Wood Processing Laboratory Faculty of Forestry,Tanjungpura University and Laboratory of PT. Duta Pertiwi Nusantara Pontianak. The adhesive used is Urea Formaldehyde with 52% Solid Content. Comparison of the composition of rice husks and sengon varies namely rice husk 50%: sengon 50%, rice husk 60%: sengon 40% and rice husk 70%: sengon 30% and variations in the levels of UF adhesives, namely 14% and 16%, with target density 0,7 gr/cm3. The particleboard was 30 cm x 30 cm x 1 cm Pressing at temperature 140oC for 8 minutes, with pressure of 25 kg/cm2. The research results of the study of density and moisture content meet the standards JIS A 5908-2003. The best particle values of rice husk and sengon with composition a ratio of rice husk 50%: sengon 50% , 16% adhesive content 16%, with density value of 0,7072 gr/cm3, moisture content 9,1949 %, thick development 12,3210 %, water absorption 68,8270 %, MOE 12110,7273 kg/cm2, MOR 161,0025 kg/cm2, firmness sticky 1,9320 kg/cm2, screw holding strength 62,3124 kg.Keywords : adhesive, composition, particle board, rice husk, sengon

Download Full-text