scholarly journals Thermo-economic Assessment of the first Integrated Solar Combined Cycle System of Hassi R’mel

Mechanika ◽  
2020 ◽  
Vol 26 (3) ◽  
pp. 242-251
Author(s):  
M. AMANI ◽  
A. SMAILI ◽  
A. GHENAIET
Keyword(s):  
Thermal Efficiency ◽  
Environmental Effect ◽  
Power Plants ◽  
Economic Assessment ◽  
Combined Cycle ◽  
Electricity Production ◽  
Fuel Saving ◽  
Electricity Cost ◽  
Cycle System ◽  
Solar Electricity

The aim of this study is the thermo-economic assessments of an integrated solar combined cycle (ISCC) system, in terms of thermal efficiency, electricity production and levelized electricity cost (LCOE). During the day light the power plant operates as an ISCC and operates as a conventional combined cycle (CC) during the night or cloudy days. In one hand the obtained results show that at the design point the solar electricity ratio may reach about 17 % and the global thermal efficiency 63 %, leading to lower fuel consumption and carbon emission. On the other hand, the economic assessment depicts that LCOE may reach 0.0222 $/kWh, which is about 28 % higher than that of (CC) power plants. Furthermore, by introducing the environmental effect LCOE becomes equal to 0.0272 $/kWh which is higher. Therefore, the annual solar contribution relatively to this ISCC installation site will allow about 18.45 million $ of fuel saving, avoiding emission of 0.89 million ton of CO2 over 30 years operation.

Evaluation for Scalability of a Combined Cycle Using Gas and Bottoming SCO2 Turbines

2015 ◽  
Author(s):  
Leonid Moroz ◽  
Petr Pagur ◽  
Oleksii Rudenko ◽  
Maksym Burlaka ◽  
Clement Joly
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Supercritical Co2 ◽  
Power Plants ◽  
Combined Cycle ◽  
Electricity Production ◽  
Working Fluid ◽  
Gas Temperature ◽  
Cycle System ◽  
Gas Turbine Exhaust

Bottoming cycles are drawing a real interest in a world where resources are becoming scarcer and the environmental footprint of power plants is becoming more controlled. Reduction of flue gas temperature, power generation boost without burning more fuel and even production of heat for cogeneration applications are very attractive and it becomes necessary to quantify how much can really be extracted from a simple cycle to be converted to a combined configuration. As supercritical CO2 is becoming an emerging working fluid [2, 3, 5, 7 and 8] due not only to the fact that turbomachines are being designed significantly more compact, but also because of the fluid’s high thermal efficiency in cycles, it raises an increased interest in its various applications. Evaluating the option of combined gas and supercritical CO2 cycles for different gas turbine sizes, gas turbine exhaust gas temperatures and configurations of bottoming cycle type becomes an essential step toward creating guidelines for the question, “how much more can I get with what I have?”. Using conceptual design tools for the cycle system generates fast and reliable results to draw this type of conclusion. This paper presents both the qualitative and quantitative advantages of combined cycles for scalability using machines ranging from small to several hundred MW gas turbines to determine which configurations of S-CO2 bottoming cycles are best for pure electricity production.

Multi Criteria Evaluation Model of Renewable Energy Power Plants Based on ELECTRE Method

2009 ◽  
Author(s):  
Jiang-Jiang Wang ◽  
You-Yin Jing ◽  
Jun-Hong Zhao
Keyword(s):  
Renewable Energy ◽  
Power Plants ◽  
Evaluation Model ◽  
Evaluation Criteria ◽  
Combined Cycle ◽  
Hydro Power ◽  
Electricity Cost ◽  
Natural Gas Combined Cycle ◽  
Electre Method ◽  
Save Energy

The feasibility evaluation of renewable energy power plants from multi criteria is necessary to save energy, protect environment and develop technology. This paper employs the improved elimination et choice translating reality (ELECTRE) method to evaluate 10 kinds of energy power plants in five criteria. The plants includes the coal fired, solar-thermal, geothermal, biomass, nuclear, photovoltaic solar, wind, ocean, hydro and natural gas combined cycle power plants. The evaluation criteria reflects four aspects from the technology, economy, environment and society. The concrete criteria are efficiency, installation, electricity cost, CO2 emission, and land requirement. Finally, the multi criteria evaluations show that the hydro power plant in the renewable energy are the optimal schemes at present.

scholarly journals Thermodynamic and Techno-Economic Analyses of a Combined Cycle Power Plant With a Simple Cycle Gas Turbine, the Bottoming Air Turbine Cycle and the Reverse Brayton Cycle

1999 ◽  
Author(s):  
Isaac Shnaid
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Combined Cycle ◽  
Simple Cycle ◽  
Brayton Cycle ◽  
Cycle System ◽  
Air Turbine ◽  
Attractive Option ◽  
Gas Turbine Exhaust ◽  
Economic Analyses

The modem combined cycle power plants achieved thermal efficiency of 50–55% by applying bottoming multistage Rankine steam cycle. At the same time, the Brayton cycle is an attractive option for a bottoming cycle engine. In the author’s US Patent No. 5,442,904 is described a combined cycle system with a simple cycle gas turbine, the bottoming air turbine Brayton cycle, and the reverse Brayton cycle. In this system, air turbine Brayton cycle produces mechanic power using exergy of gas turbine exhaust gases, while the reverse Brayton cycle refrigerates gas turbine inlet air. Using this system, supercharging of gas turbine compressor becomes possible. In the paper, thermodynamic optimization of the system is done, and the system techno-economic characteristics are evaluated.

Diagnosis of Thermal Efficiency of Advanced Combined Cycle Power Plants Using Optical Torque Sensor

2005 ◽  
Author(s):  
Shuichi Umezawa
Keyword(s):  
Thermal Efficiency ◽  
Power Plants ◽  
Power Transmission ◽  
Combined Cycle ◽  
Signal Process ◽  
Bar Code ◽  
Sensor Performance ◽  
Power Company ◽  
Optical Torque ◽  
Plant Efficiency

A new optical torque measurement method was applied to diagnosis of thermal efficiency of advanced combined cycle, i.e. ACC, plants. Since the ACC power plant comprises a steam turbine and a gas turbine and both of them are connected to the same generator, it is difficult to identify which turbine in the plant deteriorates the performance when the plant efficiency is reduced. The sensor measures axial distortion caused by power transmission by use of He-Ne laser beams, small stainless steel reflectors having bar-code patterns, and a technique of signal processing featuring high frequency. The sensor was applied to the ACC plants of TOKYO ELECTRIC POWER COMPANY, TEPCO, following the success in the application to the early combined cycle plants of TEPCO. The sensor performance was inspected over a year. After an improvement related to the signal process, it is considered that the sensor performance has reached a practical use level.

Exergy Evaluation of Two Current Advanced Power Plants: Supercritical Steam Turbine and Combined Cycle

1997 ◽  
Vol 119 (4) ◽  
pp. 250-256 ◽  
Author(s):  
H. Jin ◽  
M. Ishida ◽  
M. Kobayashi ◽  
M. Nunokawa
Keyword(s):  
Steam Turbine ◽  
Thermal Efficiency ◽  
Heat Recovery ◽  
Power Plants ◽  
Exergy Analysis ◽  
Combined Cycle ◽  
Exergy Loss ◽  
Heat Recovery Steam Generator ◽  
Combined Cycle Plant ◽  
Steam Plant

Two operating advanced power plants, a supercritical steam plant and a gas-steam turbine combined cycle, have been analyzed using a methodology of graphical exergy analysis (EUDs). The comparison of two plants, which may provide the detailed information on internal phenomena, points out several inefficient segments in the combined cycle plant: higher exergy loss caused by mixing in the combustor, higher exergy waste from the heat recovery steam generator, and higher exergy loss by inefficiency in the power section, especially in the steam turbine. On the basis of these fundamental features of each plant, we recommend several schemes for improving the thermal efficiency of current advanced power plants.

Performance Evaluation of an Integrated Solar Combined Cycle

2012 ◽  
Author(s):  
Collins O. Ojo ◽  
Damien Pont ◽  
Enrico Conte ◽  
Richard Carroni
Keyword(s):  
Solar Energy ◽  
Capital Investment ◽  
Power Plants ◽  
Solar Power ◽  
Combined Cycle ◽  
Electricity Production ◽  
Water Steam ◽  
Plant Operator ◽  
Central Receiver ◽  
Solar Field

The integration of steam from a central-receiver solar field into a combined cycle power plant (CCPP) provides an option to convert solar energy into electricity at the highest possible efficiency, because of the high pressure and temperature conditions of the solar steam, and at the lowest capital investment, because the water-steam cycle of the CCPP is in shared use with the solar field. From the operational point of view, the plant operator has the option to compensate the variability of the solar energy with fossil fuel electricity production, to use the solar energy to save fuel and to boost the plant power output, while reducing the environmental footprint of the plant operation. Alstom is able to integrate very large amounts of solar energy in its new combined-cycle power plants, in the range of the largest solar field ever built (Ivanpah Solar Power Facility, California, 3 units, total 392 MWel). The performance potential of such integration is analyzed both at base load and at part load operation of the plant. Additionally, the potential for solar retrofit of existing combined-cycle power plants is assessed. In this case, other types of concentrating solar power technologies than central receiver (linear Fresnel and trough) may be best suited to the specific conditions. Alstom is able to integrate any of these technologies into existing combined-cycle power plants.

scholarly journals The Effect of Ambient Temperature on Electric Power Generation in Natural Gas Combined Cycle Power Plant: A Case Study

2018 ◽  
Author(s):  
Günnur Şen ◽  
Mustafa Nil ◽  
Hayati Mamur ◽  
Halit Doğan ◽  
Mustafa Karamolla ◽  
...  
Keyword(s):  
Power Plant ◽  
Natural Gas ◽  
Ambient Temperature ◽  
Power Plants ◽  
Electric Energy ◽  
Combined Cycle ◽  
Electricity Production ◽  
Air Cooling ◽  
Seasonal Temperature ◽  
Natural Gas Combined Cycle

Natural gas combined cycle power plants (CCPPs) are widely used to meet peak loads in electric energy production. Continuous monitoring of the output electrical power of CCPPs is a requirement for power performance. In this study, the role of ambient temperature change having the greatest effect on electric production is investigated for a natural gas CCPP. The plant has generated electricity for fourteen years and setup at 240 MW in Aliağa, İzmir, Turkey. Depending on the seasonal temperature changes, the study data were obtained from each gas turbine (GT), steam turbine (ST) and combined cycle blocks (CCBs) in the ambient temperature range of 8-23°C. It has been found that decreases of the electric energy in the GTs because of the temperature increase and indirectly diminishes of the electricity production in the STs. As a result, the efficiency of each GT, ST and CCB reduced, although the quantity of fuel consumed by the controllers in the plant was decreased. As a result of this data, it has been recommended and applied that additional precautions have been taken for the power plant to bring the air entering the combustion chamber to ideal conditions and necessary air cooling systems have been installed.

Assessment of Humid Air Turbines in Coal-Fired High Performance Power Systems

1996 ◽  
Author(s):  
Julianne M. Klara ◽  
Robert M. Enick ◽  
Scott M. Klara ◽  
Lawrence E. Van Bibber
Keyword(s):  
Power Systems ◽  
Thermal Efficiency ◽  
High Performance ◽  
Power Plants ◽  
Combined Cycle ◽  
Humid Air ◽  
Levelized Cost Of Electricity ◽  
Capital Costs ◽  
Air Turbine ◽  
Net Power Output

The purpose of this study is to assess the feasibility of incorporating a Humid Air Turbine (HAT) into a coal-based, indirectly fired High Performance Power System (HIPPS). The HIPPS/HAT power plant exhibits a one percentage point greater thermal efficiency than the combined-cycle HIPPS plant. The capital costs for the HIPPS and HIPPS/HAT plants with identical net power output are nearly equivalent at $1380/kW. Levelized cost of electricity (COE) for the same size plants is 5.3 cents/kWh for the HIPPS plant and 5.4 cents/kWh for the HIPPS/HAT plant; the HIPPS/HAT plant improved thermal efficiency is offset by the higher fuel cost associated with a lower coal/natural gas fuel ratio. However, improved environmental performance is associated with the HIPPS/HAT cycle, as evidenced by lower CO2, SO2, and NOx emissions. Considering the uncertainties associated with the performance and cost estimates of the yet unbuilt components, the HIPPS/HAT and HIPPS power plants are presently considered to be comparable alternatives for future power generation technologies. The Department of Energy’s Combustion 2000 Program will provide revised design specifications and more accurate costs for these components allowing more definitive assessments to be performed.

Diagnosis of Thermal Efficiency of Nuclear Power Plants Using Optical Torque Sensors

2006 ◽  
Author(s):  
Shuichi Umezawa ◽  
Jun Adachi
Keyword(s):  
Power Plant ◽  
Nuclear Power Plant ◽  
Thermal Efficiency ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Torsional Rigidity ◽  
Combined Cycle ◽  
Sensor Performance ◽  
Optical Torque

A new optical torque measuring method was applied to diagnosis of thermal efficiency of nuclear power plants. The sensor allows torque deformation of the rotor caused by power transmission to be measured without contact. Semiconductor laser beams and small pieces of stainless reflector that have bar-code patterns are employed. The intensity of the reflected laser beam is measured and then input into a computer through an APD and an A/D converter having high frequency sampling rates. The correlation analysis technique can translate these data into the torque deformation angle. This angle allows us to obtain the turbine output along with the torsional rigidity and the rotating speed of the rotor. The sensor was applied to a nuclear plant of Tokyo Electric Power Company, TEPCO, following its application success to the early combined cycle plants and the advanced combined cycle plants of TEPCO. As the turbine rotor of the nuclear power plant is less exposed than that of the combined cycle plants, the measurement position is confined to a narrow gap. In order to overcome the difficulty in installation, the shape of the sensor is modified to be long and thin. Sensor performance of the nuclear power plant was inspected over a year. The value of the torsional rigidity was analyzed by the finite element method at first. Accuracy was improved by correcting the torsional rigidity so that the value was consistent with the generator output. As a result, it is considered that the sensor performance has reached a practical use level.

Sign in / Sign up

Export Citation Format

Share Document