scholarly journals Swirling Flows Characteristics in a Cylinder Under Effect of Buoyancy

Mechanika ◽  
2021 ◽  
Vol 27 (3) ◽  
pp. 201-208
Author(s):  
Mustafa FEKHAR ◽  
Rachid SACI ◽  
Renée GATIGNOL
Keyword(s):  
Aspect Ratio ◽  
Thermal Stratification ◽  
Flow Behavior ◽  
Flow Characteristics ◽  
Swirling Flows ◽  
Viscous Effects ◽  
Thermal Buoyancy ◽  
State Diagrams ◽  
The Core ◽  
Flow Stagnation

Thermal buoyancy, induced by injection or by differential heating of a tiny rod is explored to control breakdown in the core of a helical flow driven by the lid rotation of a cylinder. Three main parameters are required to characterize numerically the flow behavior; namely, the rotational Reynolds number Re, the cavity aspect ratio and the Richardson number Ri. Warm injection/rod, Ri > 0, is shown to prevent on-axis flow stagnation while breakdown enhancement is evidenced when Ri < 0. Results revealed that a bubble vortex evolves into a ring type structure which may remain robust, as observed in prior related experiments or, in contrast, disappear over a given range of parameters (Λh, Re, Ri > 0). Besides, the emergence of such a toroidal mode was not found to occur under thermal stratification induced by a differentially heated rod. Moreover, three state diagrams were established which provide detailed flow characteristics under the distinct and combined effects of buoyancy strength, viscous effects and cavity aspect ratio.

Experimental Investigation on the Thermal and Flow Characteristics in the IRWST Under Spraying of the Steam From Automatic Depressurization System in AP1000 Plant

2016 ◽  
Author(s):  
Daogang Lu ◽  
Yuhao Zhang ◽  
Zhongyi Wang ◽  
Guanghao Wu ◽  
Qiong Cao
Keyword(s):  
Thermal Stratification ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Flow Patterns ◽  
Convection Flow ◽  
Water Storage Tank ◽  
Image Velocimetry ◽  
Large Tank ◽  
Coolant System

In AP1000 plant, the automatic depressurization system (ADS) works to discharge the high-temperature and high-pressure steam from the Reactor Coolant System (RCS) primary side to the In-containment Refueling Water Storage Tank (IRWST) in the LOCA conditions. In particular, for the AP1000 plant, both the IRWST and ADS spargers are specially designed, and the ADS spargers are located in one corner of the IRWST. All the factors lead to the special and complicated thermal and flow behavior in the IRWST, which in turn have great influences on the condensation effects of the ejected steam. In the present work, an overall scaled-down IRWST and ADS sparger models are built to study the condensation and mixing phenomena in the accidental depressurization events in AP1000. Thermocouples matrix with more than 200 T-type sheathed thermocouples are utilized to measure the three dimensional temperature in the large tank. The Particle Image Velocimetry (PIV) is employed for the measurement of the natural convection flow velocity. Based on the experimental data, the local spraying flow patterns, flow behavior, and thermal stratification phenomena in IRWST etc. are analyzed. The results indicate that the spraying steam condensation flow patterns are closely related to the subcooling degree in the IRWST. In addition, the stratification number is developed to evaluate the thermal stratification extent in the IRWST, which indicates that only part of the fluid are used efficiently for condensing the spraying steam directly.

scholarly journals Large Eddy Simulations of Strongly Non-Ideal Compressible Flows through a Transonic Cascade

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 772
Author(s):  
Jean-Christophe Hoarau ◽  
Paola Cinnella ◽  
Xavier Gloerfelt
Keyword(s):  
Compressible Flows ◽  
Flow Behavior ◽  
Pressure Ratio ◽  
Organic Rankine Cycle ◽  
Ideal Gas ◽  
Operating Conditions ◽  
Large Eddy Simulations ◽  
Working Fluid ◽  
Viscous Effects ◽  
Large Eddy

Transonic flows of a molecularly complex organic fluid through a stator cascade were investigated by means of large eddy simulations (LESs). The selected configuration was considered as representative of the high-pressure stages of high-temperature Organic Rankine Cycle (ORC) axial turbines, which may exhibit significant non-ideal gas effects. A heavy fluorocarbon, perhydrophenanthrene (PP11), was selected as the working fluid to exacerbate deviations from the ideal flow behavior. The LESs were carried out at various operating conditions (pressure ratio and total conditions at inlet), and their influence on compressibility and viscous effects is discussed. The complex thermodynamic behavior of the fluid generates highly non-ideal shock systems at the blade trailing edge. These are shown to undergo complex interactions with the transitional viscous boundary layers and wakes, with an impact on the loss mechanisms and predicted loss coefficients compared to lower-fidelity models relying on the Reynolds-averaged Navier–Stokes (RANS) equations.

scholarly journals Time Dependent Lyotropic Chromonic Textures in Microfluidic Confinements

Crystals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 35 ◽  
Author(s):  
Anshul Sharma ◽  
Irvine Lian Hao Ong ◽  
Anupam Sengupta
Keyword(s):  
Phase Transition ◽  
Aspect Ratio ◽  
Temporal Dynamics ◽  
Initial Conditions ◽  
Flow Behavior ◽  
Medical Diagnostics ◽  
Time Dependent ◽  
Disodium Cromoglycate ◽  
M Phase ◽  
Static Conditions

Nematic and columnar phases of lyotropic chromonic liquid crystals (LCLCs) have been long studied for their fundamental and applied prospects in material science and medical diagnostics. LCLC phases represent different self-assembled states of disc-shaped molecules, held together by noncovalent interactions that lead to highly sensitive concentration and temperature dependent properties. Yet, microscale insights into confined LCLCs, specifically in the context of confinement geometry and surface properties, are lacking. Here, we report the emergence of time dependent textures in static disodium cromoglycate (DSCG) solutions, confined in PDMS-based microfluidic devices. We use a combination of soft lithography, surface characterization, and polarized optical imaging to generate and analyze the confinement-induced LCLC textures and demonstrate that over time, herringbone and spherulite textures emerge due to spontaneous nematic (N) to columnar M-phase transition, propagating from the LCLC-PDMS interface into the LCLC bulk. By varying the confinement geometry, anchoring conditions, and the initial DSCG concentration, we can systematically tune the temporal dynamics of the N- to M-phase transition and textural behavior of the confined LCLC. Overall, the time taken to change from nematic to the characteristic M-phase textures decreased as the confinement aspect ratio (width/depth) increased. For a given aspect ratio, the transition to the M-phase was generally faster in degenerate planar confinements, relative to the transition in homeotropic confinements. Since the static molecular states register the initial conditions for LC flows, the time dependent textures reported here suggest that the surface and confinement effects—even under static conditions—could be central in understanding the flow behavior of LCLCs and the associated transport properties of this versatile material.

Heat Transfer for High Aspect Ratio Rectangular Channels in a Stationary Serpentine Passage With Turbulated and Smooth Surfaces

2013 ◽  
Author(s):  
Matthew A. Smith ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Aspect Ratio ◽  
Flow Behavior ◽  
Reynolds Numbers ◽  
Hydraulic Diameter ◽  
Internal Cooling ◽  
Number Range ◽  
Aspect Ratios ◽  
Parallel Configuration

Heat transfer distributions are presented for a stationary three passage serpentine internal cooling channel for a range of engine representative Reynolds numbers. The spacing between the sidewalls of the serpentine passage is fixed and the aspect ratio (AR) is adjusted to 1:1, 1:2, and 1:6 by changing the distance between the top and bottom walls. Data are presented for aspect ratios of 1:1 and 1:6 for smooth passage walls and for aspect ratios of 1:1, 1:2, and 1:6 for passages with two surfaces turbulated. For the turbulated cases, turbulators skewed 45° to the flow are installed on the top and bottom walls. The square turbulators are arranged in an offset parallel configuration with a fixed rib pitch-to-height ratio (P/e) of 10 and a rib height-to-hydraulic diameter ratio (e/Dh) range of 0.100 to 0.058 for AR 1:1 to 1:6, respectively. The experiments span a Reynolds number range of 4,000 to 130,000 based on the passage hydraulic diameter. While this experiment utilizes a basic layout similar to previous research, it is the first to run an aspect ratio as large as 1:6, and it also pushes the Reynolds number to higher values than were previously available for the 1:2 aspect ratio. The results demonstrate that while the normalized Nusselt number for the AR 1:2 configuration changes linearly with Reynolds number up to 130,000, there is a significant change in flow behavior between Re = 25,000 and Re = 50,000 for the aspect ratio 1:6 case. This suggests that while it may be possible to interpolate between points for different flow conditions, each geometric configuration must be investigated independently. The results show the highest heat transfer and the greatest heat transfer enhancement are obtained with the AR 1:6 configuration due to greater secondary flow development for both the smooth and turbulated cases. This enhancement was particularly notable for the AR 1:6 case for Reynolds numbers at or above 50,000.

CFD Study on the Flow Characteristics in Filleted Microchannels

2011 ◽  
Vol 103 ◽  
pp. 268-273
Author(s):  
Hong Jie Yan ◽  
Ping Zhou ◽  
Ze Lin Xu ◽  
Zhuo Chen ◽  
Jing Wen Mo
Keyword(s):  
Pressure Drop ◽  
Aspect Ratio ◽  
Flow Model ◽  
Constant Width ◽  
Flow Characteristics ◽  
Flow Pressure ◽  
Cfd Method ◽  
Poiseuille Number ◽  
The Relationship ◽  
Laminar Flow Model

The flow characteristics of water in filleted microchannels were simulated based on CFD method. The flow pressure drop at different aspect ratioandRenumber were rearranged on the simulating results with laminar flow model. The results indicated that the pressure drop enlarges with the increase of in the case of the constant width of the microchannel. Within the range ofRenumber of interest, Poiseuille number of the flow is constant for differentRe, but decreases with increasing aspect ratio. An equation was fitted to describe the relationship betweenPonumber and aspect ratio, i.e. .

scholarly journals Studies on the Fluidized Bed Electrode

2008 ◽  
Vol 6 (1) ◽  
Author(s):  
Siva Kumar ◽  
Thilakavathi Ramamurthy ◽  
Bala Subramanian ◽  
Ahmed Basha
Keyword(s):  
Fluidized Bed ◽  
Annular Flow ◽  
Flow Model ◽  
Model Simulation ◽  
Flow Behavior ◽  
Hydrodynamic Characteristics ◽  
The Core ◽  
Particle Transfer ◽  
Fluidized Bed Electrode

The present investigation attempts to study the hydrodynamic characteristics of the fluidized bed electrode. A core-annular flow model with a transfer of particles between core-annular layers has been proposed to describe the flow behavior of conducting particles in the fluidized bed electrode. The effect of individual parameters on the rate of the particle transfer across the layer and thickness of the core-annular has been critically examined and the model simulation has been verified with the data reported in the literature.

Influence of Circumferential Inflow Distortion on the Performance of a Low Speed, High Aspect Ratio Contra Rotating Axial Fan

2014 ◽  
Vol 136 (7) ◽  
Author(s):  
Chetan Mistry ◽  
A. M. Pradeep
Keyword(s):  
Aspect Ratio ◽  
High Aspect Ratio ◽  
Rotational Speed ◽  
Total Pressure ◽  
Flow Behavior ◽  
Axial Fan ◽  
Low Speed ◽  
Overall Performance ◽  
Design Speed ◽  
Inflow Conditions

The influence of circumferential inflow distorted on the performance and flow behavior of a high aspect ratio, low speed contra rotating fan is reported in this paper. The total pressure at the inlet is artificially distorted by means of 90 deg mesh sector with a porosity of 0.70. The performance of the contra rotating fan was studied under different speed combinations of the two rotors under clean and distorted inflow conditions. Detailed flow analyses were conducted under design and off-design conditions. In order to understand the effect of distortion and its extent, the distortion sector was rotated circumferentially at intervals of 15 deg to cover the entire annulus. Detailed measurements of the total pressure, velocity components, and flow angles were carried out at the inlet of the first rotor, between the two rotors, and at the exit of the second rotor. The study reveals a few interesting aspects on the effect of inflow distortion on the performance of a contra-rotating stage. For the design speed combination and lower rotational speed of rotor-2, a reduction in the overall operating range with a shift of the peak pressure point towards higher mass flow rate, was observed. It is observed that the effect of inflow distortion at the inlet of rotor-1 gets transferred in the direction of rotor-1 rotation and spreads across the entire annulus. The opposite sense of rotation of rotor-2 causes the distortion effect to get transferred in the direction of rotation of rotor-2 with an associated reduction in the total pressure near the hub. It is observed that a higher rotational speed of the second rotor has a beneficial effect on the overall performance due to the strong suction by generated higher rotational speed of rotor-2.

Wave Propagation and Power Flow Analysis of Sandwich Structures With Internal Absorbers

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
J. S. Chen ◽  
R. T. Wang
Keyword(s):  
Wave Propagation ◽  
Power Flow ◽  
Wave Attenuation ◽  
Sandwich Structures ◽  
Flow Analysis ◽  
Flow Characteristics ◽  
Continuum Models ◽  
Sandwich Beams ◽  
The Core ◽  
In Series

This study examines wave attenuation and power flow characteristics of sandwich beams with internal absorbers. Two types of absorbing systems embedded in the core are considered, namely, a conventional spring-mass-dashpot system having a mass with a spring and a dashpot in parallel, and a relaxation system containing an additional relaxation spring added in series with the dashpot. Analytical continuum models used for interpreting the attenuation behavior of sandwich structures are presented. Through the analysis of the power flowing into the structure, the correlation of wave attenuation and energy blockage is revealed. The reduction in the power flow indicates that some amount of energy produced by the external force can be effectively obstructed by internal absorbers. The effects of parameters on peak attenuation, bandwidth, and power flow are also studied.

Sign in / Sign up

Export Citation Format

Share Document