scholarly journals Elemental contents of some medicinal plants using energy dispersive x-ray fluorescence (EDXRF)

2020 ◽  
Vol 14 (5) ◽  
pp. 202-207
Author(s):  
Djoman Djama AGBO Alfred ◽  
Joseph N’GOUAN Aka ◽  
Alain MONNEHAN Georges
Keyword(s):  
Medicinal Plants ◽  
Energy Dispersive ◽  
X Ray ◽  
Elemental Contents

scholarly journals STUDY OF MULTIELEMENTAL CONCENTRATIONS AND NANO-MICRO STRUCTURAL MORPHOLOGY IN MYRTACEAE FAMILY MEDICINAL PLANTS BY FIELD EMISSION SCANNING ELECTRON MICROSCOPE-ENERGY DISPERSIVE X-RAY SPECTROSCOPY METHOD

2019 ◽  
pp. 432-435
Author(s):  
TEERTHE SS ◽  
KERUR BR
Keyword(s):  
Trace Elements ◽  
Electron Microscope ◽  
Medicinal Plants ◽  
Scanning Electron Microscope ◽  
Field Emission ◽  
Energy Dispersive ◽  
World Health ◽  
Structural Morphology ◽  
X Ray ◽  
Scanning Electron

Objective: The essential multielemental analysis was carried out in nano- and microscale surface morphology of two useful selected species of Myrtaceae family medicinal plants such as Eucalyptus and Guava using “field emission scanning electron microscope”–“energy dispersive X-ray spectroscopy” (FESEM-EDS). To understand the elemental analysis of medicinal plant used in Bidar, Gulbarga/Kalaburagi and Yadgir districts of the Northeast Karnataka region. Methods: In the present investigation, Myrtaceae family’s medicinal plants selected. The analysis of the samples were thorough nano-micro photograph obtained by using FESEM and specific weight percent of elemental concentration analyzed by EDX/EDS. Results: The elemental concentrations such as C, O, magnesium, Al, Si, S, Cl, K, Ca, Mn, Fe, Cu, and Zn were estimated in all the collected medicinal plants and found to be within the World Health Organization (WHO’s) recommended values. FESEM morphology indicates that fine plane irregularly shaped particles, with size an average diameter 200 nm–1 μm, are found in both plants. Conclusion: The Indian Traditional Medicinal Plants have been used as a potential source for general and therapeutic medicinal purposes, including as a home remedy, Ayurvedic, and herbal drugs for the treatment of different types of human diseases. The WHO established maximum permissible limits for the consumption of major, minor, and trace elements to ensure the safe uses of medicinal plants as a drug material so as to cure the diseases. The present investigation suggests that the collected medicinal plants have good alignments of secondary metabolites, functional groups, and intake of trace elements, which are useful for treatment and preparation of new Ayurvedic, herbal, and pharmaceutical drug, pellets of very small size for alignment of different diseases.

scholarly journals Elemental contents in exotic Brazilian tropical fruits evaluated by energy dispersive X-ray fluorescence

2006 ◽  
Vol 63 (1) ◽  
pp. 82-84 ◽  
Author(s):  
Alessandra Lopes de Oliveira ◽  
Eduardo de Almeida ◽  
Fernanda Bevilácqua Rodrigues da Silva ◽  
Virgílio Franco Nascimento Filho
Keyword(s):  
Nutritional Composition ◽  
The Other ◽  
Energy Dispersive ◽  
Tamarindus Indica ◽  
Tropical Fruits ◽  
X Ray ◽  
Eugenia Uniflora ◽  
Elemental Contents ◽  
Edxrf Technique ◽  
Hancornia Speciosa

The exotic flavor of Brazilian tropical fruits led to increased consumption. Consumers awareness regarding balanced diets, makes necessary determining nutritional composition - vitamins and minerals of the fruits ordinarily consumed. This study contributed to the evaluation of macro (K, Ca) and microelements (Mn, Fe, Cu, Zn and Br) in eight exotic Brazilian tropical fruits: "abiu" (Lucuma caimito Ruiz & Pav.), "jenipapo" (Genipa americana L.), "jambo rosa" (rose apple, Eugenia Jambos L.), "jambo vermelho" (Syzygium malaccence L., Merr & Perry), "macaúba" (Acrocomia aculeata Jacq. Lood. Ex Mart.), "mangaba" (Hancornia speciosa), "pitanga" (Brazilian Cherry, Eugenia uniflora L.), and tamarind (Tamarindus indica L.), using the Energy Dispersive X-Ray Fluorescence (EDXRF) technique. "jambo vermelho" and "macaúba" presented the highest values of K concentrations, 1,558 and 1,725 mg 100 g-1, respectively. On the other hand, Ca concentrations were highest in "macaúba" (680 mg 100 g-1) and "jenipapo" (341 mg 100 g-1). The microelemental concentrations in these eight fruits ranged from: 0.9 to 2.0 mg 100 g-1 for Mn, 3.9 to 11.4 mg 100 g-1 for Fe, 0.5 to 1.0 mg 100 g-1 for Cu, 0.6 to 1.5 mg 100 g-1 for, Zn and 0.3 to 1.3 mg 100 g-1 for Br. The amounts of macro and microelements in the eight fruits analyzed were compared to other tropical fruits and it was found that some of them could be classified as rich sources for these macro and microelements.

Microanalysis of precipitates in a ferritic steel

1978 ◽  
Vol 36 (1) ◽  
pp. 618-619
Author(s):  
J.M. Titchmarsh
Keyword(s):  
Ferritic Steel ◽  
Particle Identification ◽  
Energy Dispersive ◽  
Objective Lens ◽  
Ferritic Steels ◽  
Replica Technique ◽  
X Ray ◽  
Large Numbers ◽  
Scanning Transmission ◽  
Made In

The advances in recent years in the microanalytical capabilities of conventional TEM's fitted with probe forming lenses allow much more detailed investigations to be made of the microstructures of complex alloys, such as ferritic steels, than have been possible previously. In particular, the identification of individual precipitate particles with dimensions of a few tens of nanometers in alloys containing high densities of several chemically and crystallographically different precipitate types is feasible. The aim of the investigation described in this paper was to establish a method which allowed individual particle identification to be made in a few seconds so that large numbers of particles could be examined in a few hours.A Philips EM400 microscope, fitted with the scanning transmission (STEM) objective lens pole-pieces and an EDAX energy dispersive X-ray analyser, was used at 120 kV with a thermal W hairpin filament. The precipitates examined were extracted using a standard C replica technique from specimens of a 2¼Cr-lMo ferritic steel in a quenched and tempered condition.

Energy Dispersive X-Ray Measurements of thin Metal Foils

1976 ◽  
Vol 34 ◽  
pp. 426-427
Author(s):  
J. Bentley ◽  
E. A. Kenik
Keyword(s):  
Materials Science ◽  
Energy Dispersive Spectrometer ◽  
Thin Foil ◽  
Thin Metal ◽  
Energy Dispersive ◽  
Thin Specimen ◽  
X Ray ◽  
Metal Foils ◽  
Small Probe ◽  
Scanning Transmission

Instruments combining a 100 kV transmission electron microscope (TEM) with scanning transmission (STEM), secondary electron (SEM) and x-ray energy dispersive spectrometer (EDS) attachments to give analytical capabilities are becoming increasingly available and useful. Some typical applications in the field of materials science which make use of the small probe size and thin specimen geometry are the chemical analysis of small precipitates contained within a thin foil and the measurement of chemical concentration profiles near microstructural features such as grain boundaries, point defect clusters, dislocations, or precipitates. Quantitative x-ray analysis of bulk samples using EDS on a conventional SEM is reasonably well established, but much less work has been performed on thin metal foils using the higher accelerating voltages available in TEM based instruments.

Preparation And elemental analysis of ancient fibers

1987 ◽  
Vol 45 ◽  
pp. 410-411
Author(s):  
Allen Angel ◽  
Kathryn A. Jakes
Keyword(s):  
Cross Sections ◽  
Physical Structure ◽  
Energy Dispersive ◽  
Archaeological Sites ◽  
X Ray ◽  
Long Term Storage ◽  
Backscattered Electron ◽  
Electron Imaging

Fabrics recovered from archaeological sites often are so badly degraded that fiber identification based on physical morphology is difficult. Although diagenetic changes may be viewed as destructive to factors necessary for the discernment of fiber information, changes occurring during any stage of a fiber's lifetime leave a record within the fiber's chemical and physical structure. These alterations may offer valuable clues to understanding the conditions of the fiber's growth, fiber preparation and fabric processing technology and conditions of burial or long term storage (1).Energy dispersive spectrometry has been reported to be suitable for determination of mordant treatment on historic fibers (2,3) and has been used to characterize metal wrapping of combination yarns (4,5). In this study, a technique is developed which provides fractured cross sections of fibers for x-ray analysis and elemental mapping. In addition, backscattered electron imaging (BSI) and energy dispersive x-ray microanalysis (EDS) are utilized to correlate elements to their distribution in fibers.

PHAX-SCAN: Functional integration of a Scanning Electron Microscope and an energy-dispersive x-ray analyser

1989 ◽  
Vol 47 ◽  
pp. 56-57
Author(s):  
Marc H. Peeters ◽  
Max T. Otten
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
High Speed ◽  
High Performance ◽  
Functional Integration ◽  
Energy Dispersive ◽  
X Rays ◽  
X Ray ◽  
High Speed Analysis ◽  
Scanning Electron

Over the past decades, the combination of energy-dispersive analysis of X-rays and scanning electron microscopy has proved to be a powerful tool for fast and reliable elemental characterization of a large variety of specimens. The technique has evolved rapidly from a purely qualitative characterization method to a reliable quantitative way of analysis. In the last 5 years, an increasing need for automation is observed, whereby energy-dispersive analysers control the beam and stage movement of the scanning electron microscope in order to collect digital X-ray images and perform unattended point analysis over multiple locations.The Philips High-speed Analysis of X-rays system (PHAX-Scan) makes use of the high performance dual-processor structure of the EDAX PV9900 analyser and the databus structure of the Philips series 500 scanning electron microscope to provide a highly automated, user-friendly and extremely fast microanalysis system. The software that runs on the hardware described above was specifically designed to provide the ultimate attainable speed on the system.

A morphological and energy-dispersive x-ray spectroscopy (EDS) investigation of separator-grade cellophane

1994 ◽  
Vol 52 ◽  
pp. 430-431
Author(s):  
Michael E. Rock ◽  
Vern Kennedy ◽  
Bhaskar Deodhar ◽  
Thomas G. Stoebe
Keyword(s):  
Extrusion Process ◽  
Morphological Characterization ◽  
Energy Dispersive ◽  
Regenerated Cellulose ◽  
Battery System ◽  
X Ray ◽  
Functional Differences ◽  
Transmission Electron ◽  
Separator Material ◽  
Underwater Target

Cellophane is a composite polymer material, made up of regenerated cellulose (usually derived from wood pulp) which has been chemically transformed into "viscose", then formed into a (1 mil thickness) transparent sheet through an extrusion process. Although primarily produced for the food industry, cellophane's use as a separator material in the silver-zinc secondary battery system has proved to be another important market. We examined 14 samples from five producers of cellophane, which are being evaluated as the separator material for a silver/zinc alkaline battery system in an autonomous underwater target vehicle. Our intent was to identify structural and/or chemical differences between samples which could be related to the functional differences seen in the lifetimes of these various battery separators. The unused cellophane samples were examined by transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS). Cellophane samples were cross sectioned (125-150 nm) using a diamond knife on a RMC MT-6000 ultramicrotome. Sections were examined in a Philips 430-T TEM at 200 kV. Analysis included morphological characterization, and EDS (for chemical composition). EDS was performed using an EDAX windowless detector.

Sign in / Sign up

Export Citation Format

Share Document