scholarly journals Investigation the effect of Graphene on The Morphology, Mechanical and Thermal properties of PLA/PMMA Blends

2015 ◽  
Vol 37 ◽  
pp. 15 ◽  
Author(s):  
Azin Paydayesh ◽  
Ahmad Aref Azar ◽  
Azam Jalali Arani
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Thermal Analysis ◽  
Thermal Properties ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Elongation At Break ◽  
Blend Morphology ◽  
Pmma Blends ◽  
Thermal Stability Of

In this work, Poly Lactic Acid/Poly methyl Methacrylate (PLA/PMMA) blends in various compositions prepared and morphology and properties of these blends was investigated. Moreover, the effect of adding different amounts of Graphene Nanoplatelets (GNP) on the morphology of the blends (by SEM), the interaction of nanopalates with polymer phases (by FTIR) and its effect on the mechanical properties and thermal stability of the samples were examined. The results of the study showed that in different amounts of graphene, these plates were preferentially located in the polymer phases dissimilarly and thus, caused the change of the blend morphology. In addition, measuring the mechanical properties by tensile test and results of thermal analysis by TGA indicated the improvement of thermal stability, modulus and mechanical strength and reduction of the elongation at break of graphene containing blends with increasing the loading of GNP. The changing behavior of the mechanical and thermal properties was proportional to the Graphene localization in blend phases.

Morphology, Mechanical and Thermal Properties of Poly(Lactic Acid)/Propylene-Ethylene Copolymer/Cellulose Composites

2019 ◽  
Vol 972 ◽  
pp. 172-177
Author(s):  
Sirirat Wacharawichanant ◽  
Patteera Opasakornwong ◽  
Ratchadakorn Poohoi ◽  
Manop Phankokkruad
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Tensile Stress ◽  
Cellulose Fibers ◽  
Phase Morphology ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Ethylene Copolymer ◽  
Thermal Stability Of

This work studied the effects of various types of cellulose fibers on the morphology, mechanical and thermal properties of poly(lactic acid) (PLA)/propylene-ethylene copolymer (PEC) (90/10 w/w) blends. The PLA/PEC blends before and after adding cellulose fibers were prepared by melt blending method in the internal mixer and molded by compression method. The morphological analysis observed that the presence of cellulose in PLA did not change the phase morphology of PLA, and PLA/cellulose composite surfaces were observed the cellulose fibers inserted in PLA matrix and fiber pull-out. The phase morphology of PLA/PEC blends was changed from brittle fracture to ductile fracture behavior and showed the phase separation between PLA and PEC phases. The presence of celluloses did not improve the compatibility between PLA and PEC phases. The tensile stress and strain curves found that the tensile stress of PLA was the highest value. The addition of all celluloses increased Young’s modulus of PLA. The PEC presence increased the tensile strain of PLA over two times when compared with neat PLA and PLA was toughened by PEC. The incorporation of cellulose fibers in PLA/PEC blends could improve Young’s modulus, tensile strength, and stress at break of the blends. The thermal stability showed that the degradation temperatures of all types of cellulose were less than the degradation temperatures of PLA. Thus, the incorporation of cellulose in PLA could not enhance the thermal stability of PLA composites and PLA/PEC composites. The degradation temperature of PEC was the highest value, but it could not improve the thermal stability of PLA. The incorporation of cellulose fibers had no effect on the melting temperature of the PLA blend and composites.

scholarly journals Mechanical and Thermal Properties of Montmorillonite-Reinforced Polypropylene/Rice Husk Hybrid Nanocomposites

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1557 ◽  
Author(s):  
Khaliq Majeed ◽  
Ashfaq Ahmed ◽  
Muhammad Saifullah Abu Bakar ◽  
Teuku Meurah Indra Mahlia ◽  
Naheed Saba ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Thermal Properties ◽  
Rice Husk ◽  
Hybrid Nanocomposites ◽  
Commercial Application ◽  
Mechanical And Thermal Properties ◽  
Melt Mixing ◽  
Compatibilizing Agent ◽  
Thermal Stability Of

In recent years, there has been considerable interest in the use of natural fibers as potential reinforcing fillers in polymer composites despite their hydrophilicity, which limits their widespread commercial application. The present study explored the fabrication of nanocomposites by melt mixing, using an internal mixer followed by a compression molding technique, and incorporating rice husk (RH) as a renewable natural filler, montmorillonite (MMT) nanoclay as water-resistant reinforcing nanoparticles, and polypropylene-grafted maleic anhydride (PP-g-MAH) as a compatibilizing agent. To correlate the effect of MMT delamination and MMT/RH dispersion in the composites, the mechanical and thermal properties of the composites were studied. XRD analysis revealed delamination of MMT platelets due to an increase in their interlayer spacing, and SEM micrographs indicated improved dispersion of the filler(s) from the use of compatibilizers. The mechanical properties were improved by the incorporation of MMT into the PP/RH system and the reinforcing effect was remarkable as a result of the use of compatibilizing agent. Prolonged water exposure of the prepared samples decreased their tensile and flexural properties. Interestingly, the maximum decrease was observed for PP/RH composites and the minimum was for MMT-reinforced and PP-g-MAH-compatibilized PP/RH composites. DSC results revealed an increase in crystallinity with the addition of filler(s), while the melting and crystallization temperatures remained unaltered. TGA revealed that MMT addition and its delamination in the composite systems improved the thermal stability of the developed nanocomposites. Overall, we conclude that MMT nanoclay is an effective water-resistant reinforcing nanoparticle that enhances the durability, mechanical properties, and thermal stability of composites.

Effect of Blend Ratio on the Mechanical and Thermal Properties of Polyurethane/Silicone Rubber Conductive Material

2018 ◽  
Vol 280 ◽  
pp. 264-269
Author(s):  
Heng Chun Wei ◽  
Teh Pei Leng ◽  
Yeoh Chow Keat
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Thermal Properties ◽  
Silicone Rubber ◽  
Conductive Filler ◽  
Material Testing ◽  
Testing System ◽  
Mechanical And Thermal Properties ◽  
Blend Ratio ◽  
Thermal Stability Of

This work reports on mechanical and thermal properties of a novel polymer blend. Blends were prepared by mixing silicone rubber with diphenyl – 4,4 – dissocyanate in different ratios. Graphene nanoplatelets was added as conductive filler to improve the electrical conductivity of the blends. The mechanical properties, including tensile and tear performances were measured by a material testing system. The thermal stability of the blends was measured by thermogravimetric analysis. Incorporation 20 vol.% of silicone rubber can help to improve the thermal stability of the blend, meanwhile optimum mechanical properties of the blends is achieved.

scholarly journals Recycling of Mixed Poly(Ethylene-terephthalate) and Poly(Lactic Acid)

2019 ◽  
Vol 253 ◽  
pp. 02005
Author(s):  
Daniel Gere ◽  
Tibor Czigany
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Lactic Acid ◽  
Impact Strength ◽  
Ethylene Terephthalate ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Poly Ethylene Terephthalate ◽  
Poly Ethylene ◽  
Thermal Stability Of

Nowadays, PLA is increasingly used as a packaging material, therefore it may appear in the petrol-based polymer waste stream. However, with the today’s mechanical recycling technologies PLA and PET bottles cannot be easily or cheaply separated. Therefore, our goal was to investigate the mechanical, morphological and thermal properties of different PET and PLA compounds in a wide range of compositions. We made different compounds from poly(ethylene-terephthalate) (PET) and poly(lactic acid) (PLA) by extrusion, and injection molded specimens from the compounds. We investigated the mechanical properties and the phase morphology of the samples and the thermal stability of the regranulates. PET and PLA are thermodynamically immiscible, therefore we observed a typical island-sea type morphology in SEM micrographs. When PLA was added, the mechanical properties (tensile strength, modulus, elongation at break and impact strength) changed significantly. The Young’s modulus increased, while elongation at break and impact strength decreased with the increase of the weight fraction of PLA. The TGA results indicated that the incorporation of PLA decreased the thermal stability of the PET/PLA blends.

Mechanical Properties and Thermal Stability of TiO2 Nanofiller Reinforced Silicone Sealants

2016 ◽  
Vol 864 ◽  
pp. 23-27
Author(s):  
Ananda Manuela S. Mandalihan ◽  
Jaya L. Sitjar ◽  
Eduardo Magdaluyo Jr.
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Construction Materials ◽  
Mechanical And Thermal Properties ◽  
Glass Panel ◽  
Elongation At Break ◽  
Structural Applications ◽  
Modulus Of Resilience ◽  
Thermal Stability Of ◽  
Physical Crosslinking

Structural sealants are one of the most essential construction materials due to a rising demand of buildings having glass panel faćades. Silicones are the most preferred base component due to their excellent properties appropriate for structural applications. The effect of titanium dioxide (TiO2) nanofillers on the mechanical and thermal properties of commercially available silicone-based sealants was investigated. The incorporation of 1 wt% and 2 wt% of TiO2 has caused an increase on the elongation at break SSG4000E and SilPruf SCS2000N sealants while an increase on the modulus of resilience was observed at SilPruf SCS2000N with 1wt% TiO2. The elastic modulus was highest at 5 wt% TiO2 for all sealants. Swelling behavior decreased with increasing nanofiller due to the physical crosslinking effect, thus preventing the diffusion of the solvent into the material. Thermal stability also improved with the incorporation of 2 wt% TiO2 as observed in the increase of the onset temperature of decomposition.

scholarly journals Study on PLA/PA11 Bio-Based Toughening Melt-Blown Nonwovens

2020 ◽  
Vol 20 (1) ◽  
pp. 24-31 ◽  
Author(s):  
Feichao Zhu ◽  
Bin Yu ◽  
Juanjuan Su ◽  
Jian Han
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Average Diameter ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Polyamide 11 ◽  
Rheological Behaviors ◽  
Dispersed Phases ◽  
Thermal Stability Of ◽  
Morphology And Mechanical Properties

AbstractWith aim to improve the mechanical and thermal properties of poly (lactic acid) (PLA) melt-blown nonwovens (MBs), polyamide 11 (PA11) was melt blended with PLA at the weight proportions of PLA/PA11 (95/5, 90/10, 85/15, 80/20), and the corresponding PLA/PA11 MBs were also manufactured. The crystallization, thermal and rheological behaviors of PLA/PA11 blends were investigated. PLA/PA11 MBs were also characterized by morphology and mechanical properties. The results indicated that PA11, as globular dispersed phases, formed confined crystals and could improve the thermal stability of PLA matrix. The viscosity of PLA/PA11 blends was slightly increased but the rheological behaviors of “shear-thinning” kept unchanged in comparison with PLA. The average diameter of PLA/PA11 MB fibers was slightly increased, whereas the toughness of PLA/PA11 MBs including the strength and elongation were efficiently enhanced compared with those of PLA MBs.

scholarly journals Biodegradable Blends of Thermoplastic Waxy Starch and Poly(ε-caprolactone) Obtained by High Shear Extrusion: Rheological, Mechanical, Morphological and Thermal Properties

2021 ◽  
Author(s):  
Anderson F. Manoel ◽  
Pedro Claro ◽  
Luiz H. C. Mattoso ◽  
Jose M. Marconcini ◽  
Gerson L. Mantovani
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Thermal Analysis ◽  
Thermal Properties ◽  
Polymer Blends ◽  
High Shear ◽  
Biodegradable Material ◽  
Waxy Starch ◽  
Thermal Stability Of ◽  
Biodegradable Blends

Abstract The aim of this work was to develop polymer blends of plasticized thermoplastic waxy starch (TPS) and poly(ɛ-caprolactone) (PCL) using the largest amount of TPS possible to obtain a biodegradable material motivated by sustainability issues and to replace petrochemical-based polymers with alternatives based on biopolymers. Addition of TPS to other polymers has been used to obtain cheaper and increasingly biodegradable final products. However, TPS presents limited mechanical properties, and mixing with other polymers such as PCL is necessary to overcome these limitations and improve its processability. TPS was processed by extrusion and thermo-compression using 30 wt% glycerol. The blends were suitably processed by extrusion and further injected. The TPS/PCL blends were studied by varying the amount of PCL in a range of 10 wt% in increasing order of addition. Thermal analysis showed that introducing PCL in TPS increased Tonset because of the higher thermal stability of the former, and that the obtained blends presented a behavior intermediate to that of neat polymers.

Thermal and Mechanical Properties of Mulch Film from Poly(Lactic Acid)/Expoxidized Natural Rubber Blends Filled with Rutile TiO2 as Fillers

2013 ◽  
Vol 844 ◽  
pp. 65-68
Author(s):  
Pranee Nuinu ◽  
Kittikorn Samosorn ◽  
Kittisak Srilatong ◽  
Siripa Tongbut ◽  
Sayant Saengsuwan
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Thermal Stability ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Natural Rubber ◽  
Decomposition Temperature ◽  
Poly Lactic Acid ◽  
Thermal And Mechanical Properties ◽  
Thermal Stability Of

The aim of this research was to reduce and improve the brittleness and thermal properties of poly lactic acid (PLA), respectively. Epoxidized natural rubber (ENR) was used to enhance the toughness and rutile titanium dioxide (R-TiO2) as filler was also incorporated to improve the thermal properties of the PLA. 10wt% ENR with epoxidation contents of 25 mol% (ENR25) and 50 mol% (ENR50) and various R-TiO2contents (0-10 phr)were compounded with PLA by using a twin-screw extruder at 155-165°C and a rotor speed of 40 rpm. The pellets of blends were then formed a thin film using a cast film extruder machine and cooled down under air flow. Thermal and mechanical properties and morphology of PLA/ENR/R-TiO2thin film were investigated. The crystallinity of PLA was found to increase with addition of ENR. The mechanical properties of thin film showed that the ENR50 enhanced the elongation but reduced the tensile strength of PLA with addition of R-TiO2at 5 and 10 phr, respectively. The TGA indicated that the addition of 10 phr R-TiO2increased in the decomposition temperature at 5% weight loss (Td5%) of PLA/ENR film. Thus the thermal stability of PLA/ENR50 was found to improve with addition of R-TiO2. From morphology study, the ENR50 phase showed a good dispersion in the PLA matrix. In conclusion, the addition of ENR and R-TiO2was found to enhance both toughness and thermal stability of PLA.

Sign in / Sign up

Export Citation Format

Share Document