scholarly journals LIMITS OF THE NEW TRANSMISSION FORMULA FOR PI-TYPE FLOATING BREAKWATERS

2012 ◽  
Vol 1 (33) ◽  
pp. 47
Author(s):  
Piero Ruol ◽  
Luca Martinelli ◽  
Paolo Pezzutto
Keyword(s):  
Numerical Simulations ◽  
Wave Transmission ◽  
Experimental Results ◽  
The One ◽  
Floating Breakwaters

The aim of this work is to assess, by means of available experimental results and numerical simulations, the possible extension of the range of application of the formula proposed by Ruol et al. (J. Wat. Port, Coast. Ocean Eng., 1, 2013), giving wave transmission for chain-moored -type floating breakwaters. The formula is here applied out of the range used for its calibration and even to other types of FBs. The error between predicted and measured values is described and discussed with reference to the main geometrical variables. It appears that the formula performs fairly well for the box-type FB, but not in cases characterized by very different mooring stiffness compared to the one used for calibration. For instance in case of fixed or tethered FBs, the formula significantly overestimates the wave transmission.

Vortex Annihilation Dependence of Chirality in Asymmetric Permalloy Dots

SPIN ◽  
2019 ◽  
Vol 09 (01) ◽  
pp. 1950001
Author(s):  
Kuo-Ming Wu ◽  
Chao-Hsien Huang ◽  
Deng-Shiang Shiu ◽  
Yun Hong ◽  
Kao-Fan Lai ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Numerical Simulations ◽  
Boundary Effect ◽  
Experimental Results ◽  
Magnetic Disks ◽  
Asymmetry Effect ◽  
Asymmetric Shape ◽  
In Series ◽  
The Asymmetry ◽  
The One

Geometric asymmetry effect on vortex annihilation was investigated in series of submicro-scaled permalloy dots. By introducing the one-side-flat asymmetric shape into circular magnetic disks, the original degenerate signals of vortex annihilation for different chirality are separated into two different trajectories, where the asymmetry level is quantified by an excised angle. The separation of annihilation field for clockwise and counterclockwise vortex shows as a function of the excised angle. The asymmetry influence on the separation of annihilation field is discussed from the view of disk aspect ratio and flat boundary effect. Comparison of experimental results with numerical simulations is also presented.

Numerical investigation of the propagation of shock waves in rigid porous materials: development of the computer code and comparison with experimental results

1996 ◽  
Vol 324 ◽  
pp. 163-179 ◽  
Author(s):  
A. Levy ◽  
G. Ben-Dor ◽  
S. Sorek
Keyword(s):  
Porous Materials ◽  
Initial Conditions ◽  
Computer Code ◽  
Experimental Results ◽  
Numerical Code ◽  
Materials Development ◽  
Numerical Predictions ◽  
Wide Range ◽  
Dimensional Version ◽  
The One

The governing equations of the flow field which is obtained when a thermoelastic rigid porous medium is struck head-one by a shock wave are developed using the multiphase approach. The one-dimensional version of these equations is solved numerically using a TVD-based numerical code. The numerical predictions are compared to experimental results and good to excellent agreements are obtained for different porous materials and a wide range of initial conditions.

Natural Vulcanization Accelerators in Hevea Latex

1948 ◽  
Vol 21 (4) ◽  
pp. 853-859
Author(s):  
R. F. A. Altman
Keyword(s):  
Amino Acids ◽  
Experimental Results ◽  
The Other ◽  
Active Nitrogen ◽  
Nitrogen Bases ◽  
Other Hand ◽  
Decomposition Processes ◽  
Volatile Products ◽  
Nitrogenous Substances ◽  
The One

Abstract As numerous investigators have shown, some of the nonrubber components of Hevea latex have a decided accelerating action on the process of vulcanization. A survey of the literature on this subject points to the validity of certain general facts. 1. Among the nonrubber components of latex which have been investigated, certain nitrogenous bases appear to be most important for accelerating the rate of vulcanization. 2. These nitrogen bases apparently occur partly naturally in fresh latex, and partly as the result of putrefaction, heating, and other decomposition processes. 3. The nitrogen bases naturally present in fresh latex at later stages have been identified by Altman to be trigonelline, stachhydrine, betonicine, choline, methylamine, trimethylamine, and ammonia. These bases are markedly active in vulcanization, as will be seen in the section on experimental results. 4. The nitrogenous substances formed by the decomposition processes have only partly been identified, on the one hand as tetra- and pentamethylene diamine and some amino acids, on the other hand as alkaloids, proline, diamino acids, etc. 5. It has been generally accepted that these nitrogenous substances are derived from the proteins of the latex. 6. Decomposition appears to be connected with the formation of a considerable amount of acids. 7. The production of volatile nitrogen bases as a rule accompanies the decomposition processes. These volatile products have not been identified. 8. The active nitrogen bases, either already formed or derived from complex nitrogenous substances, seem to be soluble in water but only slightly soluble in acetone.

Additive manufacturing of pure copper: From numerical simulations to experimental results

2021 ◽  
Author(s):  
Hagen Kohl ◽  
Lisa Schade ◽  
Gabor Matthäus ◽  
Tobias Ullsperger ◽  
Burak Yürekli ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Numerical Simulations ◽  
Pure Copper ◽  
Experimental Results

Crashworthiness Performance of Mass-Efficient Extruded Structures

2002 ◽  
Author(s):  
Robert R. Mayer ◽  
Weigang Chen ◽  
Anil Sachdev
Keyword(s):  
Numerical Simulations ◽  
Single Cell ◽  
Experimental Testing ◽  
Experimental Studies ◽  
Nonlinear Material ◽  
Dynamic Strain ◽  
Cell Design ◽  
Explicit Finite Element ◽  
The One ◽  
Crushing Behavior

Theoretical, numerical and experimental studies were conducted on the axial crushing behavior of traditional single-cell and innovative four-cell extrusions. Two commercial aluminum alloys, 6061 and 6063, both with two tempers (T4 and T6), were considered in the study. Testing coupons taken from the extrusions assessed the nonlinear material properties. A theoretical solution was available for the one-cell design, and was developed for the mean crushing force of the four-cell section. Numerical simulations were carried out using the explicit finite element code LS-DYNA. The aluminum alloy 6063T4 was found to absorb less energy than 6061T4, for both the one-cell and four-cell configurations. Both 6061 and 6063 in the T6 temper were found to have significant fracture in the experimental testing. Theoretical analysis and numerical simulations predicted a greater number of folds for the four-cell design, as compared to the one-cell design, and this was confirmed in the experiments. The theoretical improvement in energy absorption of 57% for the four-cell in comparison with the one-cell design was confirmed by experiment. The good agreement between the theoretical, numerical and experimental results allows confidence in the application of the theoretical and numerical tools for both single-cell and innovative four-cell extrusions. It was also demonstrated that these materials have very little dynamic strain rate effect.

Effect of Ramp Angle on the Anti-Loosening Ability of Wedge Self-Locking Nuts Under Vibration

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Jianhua Liu ◽  
Hao Gong ◽  
Xiaoyu Ding
Keyword(s):  
Finite Element ◽  
Numerical Simulations ◽  
Production Technology ◽  
Material Properties ◽  
Threshold Value ◽  
Commercial Production ◽  
Experimental Results ◽  
Fe Method ◽  
Transversal Vibration

Recently, the wedge self-locking nut, a special anti-loosening product, is receiving more attention because of its excellent reliability in preventing loosening failure under vibration conditions. The key characteristic of a wedge self-locking nut is the special wedge ramp at the root of the thread. In this work, the effect of ramp angle on the anti-loosening ability of wedge self-locking nuts was studied systematically based on numerical simulations and experiments. Wedge self-locking nuts with nine ramp angles (10 deg, 15 deg, 20 deg, 25 deg, 30 deg, 35 deg, 40 deg, 45 deg, and 50 deg) were modeled using a finite element (FE) method, and manufactured using commercial production technology. Their anti-loosening abilities under transversal vibration conditions were analyzed based on numerical and experimental results. It was found that there is a threshold value of the initial preload below which the wedge self-locking nuts would lose their anti-loosening ability. This threshold value of initial preload was then proposed for use as a criterion to evaluate the anti-loosening ability of wedge self-locking nuts quantitatively and to determine the optimal ramp angle. Based on this criterion, it was demonstrated, numerically and experimentally, that a 30 deg wedge ramp resulted in the best anti-loosening ability among nine ramp angles studied. The significance of this study is that it provides an effective method to evaluate the anti-loosening ability of wedge self-locking nuts quantitatively, and determined the optimal ramp angle in terms of anti-loosening ability. The proposed method can also be used to optimize other parameters, such as the material properties and other dimensions, to guarantee the best anti-loosening ability of wedge self-locking nuts.

scholarly journals Numerical Simulations of V-Shaped Plates Subjected to Blast Loadings: A Validation Study

2016 ◽  
Vol 10 (11) ◽  
pp. 203
Author(s):  
Mohd Zaid Othman ◽  
Qasim H. Shah ◽  
Muhammad Akram Muhammad Khan ◽  
Tan Kean Sheng ◽  
M. A. Yahaya ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Variable Mass ◽  
Blast Loading ◽  
Experimental Results ◽  
Average Difference ◽  
Simulation Results ◽  
Blast Loadings ◽  
Carrier Vehicle ◽  
Good Agreement

A series of numerical simulations utilizing LS-DYNA was performed to determine the mid-point deformations of V-shaped plates due to blast loading. The numerical simulation results were then compared with experimental results from published literature. The V-shaped plate is made of DOMEX 700 and is used underneath an armour personal carrier vehicle as an anti-tank mine to mitigate the effects of explosion from landmines in a battlefield. The performed numerical simulations of blast loading of V-shaped plates consisted of various angles i.e. 60°, 90°, 120°, 150° and 180°; variable mass of explosives located at the central mid-point of the V-shaped vertex with various stand-off distances. It could be seen that the numerical simulations produced good agreement with the experimental results where the average difference was about 26.6%.

Grinding Performance of Porous Diamond Wheels on Different Materials

2011 ◽  
Vol 189-193 ◽  
pp. 3191-3197
Author(s):  
Qiu Lian Dai ◽  
Can Bin Luo ◽  
Fang Yi You
Keyword(s):  
Grain Size ◽  
Specific Energy ◽  
Experimental Results ◽  
Grinding Process ◽  
High Porosity ◽  
Grinding Forces ◽  
Abrasive Grain ◽  
Grinding Conditions ◽  
Medium Porosity ◽  
The One

In this paper, metal-bonded diamond wheels of different sized abrasive grain with different porosity were fabricated. Grinding experiments with these wheels on three kinds of materials were carried out under different grinding conditions. Experimental results revealed that wheel with high porosity (38%) had smaller grinding forces and specific energy than the one with a medium porosity (24%) on grinding G603. However, on grinding harder materials like Red granite or ceramics of Al2O3, the wheel with 38% porosity had bigger grinding forces and specific energy than the wheel with 24% porosity. Both wheels exhibited good self-sharpening capability during the grinding process of G603 and Red granite, but on grinding ceramics of Al2O3 the wheel with 38% porosity displayed in dull state during the grinding process . With the same porosity, the grinding forces of the wheel with a grain size of 230/270 US mesh were lower than the one with a grain size of W10 when grinding Red granite and ceramics of Al2O3. However revising results were obtained on grinding G603.

Modal Simulation and Testing of a Micro-Manipulator

2004 ◽  
Vol 127 (3) ◽  
pp. 515-519 ◽  
Author(s):  
Yongjun Lai ◽  
Marek Kujath ◽  
Ted Hubbard
Keyword(s):  
Numerical Simulations ◽  
Degrees Of Freedom ◽  
Compliant Mechanism ◽  
Dynamic Properties ◽  
Experimental Results ◽  
Mass Model ◽  
Thermal Actuators ◽  
Micro Manipulator ◽  
Six Dof

A micro-machined manipulator with three kinematic degrees-of-freedom (DOF): x, y, and φ is presented. The manipulator is driven by three thermal actuators. A six DOF discrete spring-mass model of the compliant mechanism is developed which manifests the dynamic properties of the device. Numerical simulations are compared with experimental results.

Sign in / Sign up

Export Citation Format

Share Document