Numerical Study on Optics and Heat Transfer of Solar Reactor for Methane Thermal Decomposition

This study aims to reduce greenhouse gas emissions to the atmosphere and effectively utilize wasted resources by converting methane, the main component of biogas, into hydrogen. Therefore, a reactor was developed to decompose methane into carbon and hydrogen using solar thermal sources instead of traditional energy sources, such as coal and petroleum. The optical distributions were analyzed using TracePro, a Monte Carlo ray-tracing-based program. In addition, Fluent, a computational fluid dynamics program, was used for the heat and mass transfer, and chemical reaction. The cylindrical indirect heating reactor rotates at a constant speed to prevent damage by the heat source concentrated at the solar furnace. The inside of the reactor was filled with a porous catalyst for methane decomposition, and the outside was surrounded by insulation to reduce heat loss. The performance of the reactor, according to the cavity model, was calculated when solar heat was concentrated on the reactor surface and methane was supplied into the reactor in an environment with a solar irradiance of 700 W/m2, wind speed of 1 m/s, and outdoor temperature of 25 °C. As a result, temperature, methane mass fraction distribution, and heat loss amounts for the two cavities were obtained, and it was found that the effect on the conversion rate was largely dependent on a temperature over 1000 °C in the reactor. Moreover, the heat loss of the full-cavity model decreased by 12.5% and the methane conversion rate increased by 33.5%, compared to the semi-cavity model. In conclusion, the high-temperature environment of the reactor has a significant effect on the increase in conversion rate, with an additional effect of reducing heat loss.

Polymeric Microfiltration Membranes Modification by Supercritical Solvent Impregnation—Potential Application in Open Surgical Wound Ventilation

This study investigated supercritical solvent impregnation of polyamide microfiltration membranes with carvacrol and the potential application of the modified membranes in ventilation of open surgical wounds. The impregnation process was conducted in batch mode at a temperature of 40 °C under pressures of 10, 15, and 20 MPa for contact times from 1 to 6 h. FTIR was applied to confirm the presence of carvacrol on the membrane surface. In the next step, the impact of the modification on the membrane structure was studied using scanning electron and ion beam microscopy and cross-filtration tests. Further, the release of carvacrol in carbon dioxide was determined, and finally, an open thoracic cavity model was applied to evaluate the efficiency of carvacrol-loaded membranes in contamination prevention. Carvacrol loadings of up to 43 wt.% were obtained under the selected operating conditions. The swelling effect was detectable. However, its impact on membrane functionality was minor. An average of 18.3 µg of carvacrol was released from membranes per liter of carbon dioxide for the flow of interest. Membranes with 30–34 wt.% carvacrol were efficient in the open thoracic cavity model applied, reducing the contamination levels by 27% compared to insufflation with standard membranes.

Coupling framework (1.0) for the PISM (1.1.4) ice sheet model and the MOM5 (5.1.0) ocean model via the PICO ice shelf cavity model in an Antarctic domain

The past and future evolution of the Antarctic Ice Sheet is largely controlled by interactions between the ocean and floating ice shelves. To investigate these interactions, coupled ocean and ice sheet model configurations are required. Previous modelling studies have mostly relied on high-resolution configurations, limiting these studies to individual glaciers or regions over short timescales of decades to a few centuries. We present a framework to couple the dynamic ice sheet model PISM (Parallel Ice Sheet Model) with the global ocean general circulation model MOM5 (Modular Ocean Model) via the ice shelf cavity model PICO (Potsdam Ice-shelf Cavity mOdel). As ice shelf cavities are not resolved by MOM5 but are parameterized with the PICO box model, the framework allows the ice sheet and ocean components to be run at resolutions of 16 km and 3∘ respectively. This approach makes the coupled configuration a useful tool for the analysis of interactions between the Antarctic Ice Sheet and the global ocean over time spans of the order of centuries to millennia. In this study, we describe the technical implementation of this coupling framework: sub-shelf melting in the ice sheet component is calculated by PICO from modelled ocean temperatures and salinities at the depth of the continental shelf, and, vice versa, the resulting mass and energy fluxes from melting at the ice–ocean interface are transferred to the ocean component. Mass and energy fluxes are shown to be conserved to machine precision across the considered component domains. The implementation is computationally efficient as it introduces only minimal overhead. Furthermore, the coupled model is evaluated in a 4000 year simulation under constant present-day climate forcing and is found to be stable with respect to the ocean and ice sheet spin-up states. The framework deals with heterogeneous spatial grid geometries, varying grid resolutions, and timescales between the ice and ocean component in a generic way; thus, it can be adopted to a wide range of model set-ups.

Monocytic Ontogeny of Regenerated Macrophages Characterizes the Mesotheliomagenic Responses to Carbon Nanotubes

Macrophages are not only derived from circulating blood monocytes or embryonic precursors but also expand by proliferation. The origin determines macrophage fate and functions in steady state and pathological conditions. Macrophages predominantly infiltrate fibre-induced mesothelioma tumors and contribute to cancer development. Here, we revealed their ontogeny by comparing the response to needle-like mesotheliomagenic carbon nanotubes (CNT-7) with tangled-like non-mesotheliomagenic CNT-T. In a rat peritoneal cavity model of mesothelioma, both CNT induced a rapid macrophage disappearance reaction (MDR) of MHCIIlow resident macrophages generating an empty niche available for macrophage repopulation. Macrophage depletion after mesotheliomagenic CNT-7 was followed by a substantial inflammatory reaction, and macrophage replenishment completed after 7 days. Thirty days after non-mesotheliomagenic CNT-T, macrophage repopulation was still incomplete and accompanied by a limited inflammatory reaction. Cell depletion experiments, flow cytometry and RNA-seq analysis demonstrated that, after mesotheliomagenic CNT-7 exposure, resident macrophages were mainly replaced by an influx of monocytes, which differentiated locally into MHCIIhigh inflammatory macrophages. In contrast, the low inflammatory response induced by CNT-T was associated by the accumulation of self-renewing MHCIIlow macrophages that initially derive from monocytes. In conclusion, the mesotheliomagenic response to CNT specifically relies on macrophage niche recolonization by monocyte-derived inflammatory macrophages. In contrast, the apparent homeostasis after non-mesotheliomagenic CNT treatment involves a macrophage regeneration by proliferation. Macrophage depletion and repopulation are thus decisive events characterizing the carcinogenic activity of particles and fibres.

Changes in Denture Retention With Denture Adhesives and Oral Moisturizers for the Oral Cavity

Background: It is difficult to maintain dentures during meals. This study aimed to assess changes in denture retention between rest and function using denture adhesives and oral moisturizers in an oral cavity model.Methods: The following test samples were applied between the palatal plate and the edentulous jaw ridge model: denture adhesive, denture adhesive for dry mouth, oral moisturizer, and denture moisturizer. The retentive force was measured under two conditions: at rest while immersed in water and during function with a 2.5-kg load applied. The plate was pulled perpendicular to the occlusal plane and the retentive force was measured using a digital force gauge.Results: Under dry conditions, denture adhesive for dry mouth and oral moisturizer had a significantly higher retentive force than denture adhesive and denture moisturizer. After 30 min of immersion in water, the retentive force of the denture adhesive increased while that of the oral moisturizer decreased. After 30 mins of function, the retentive force of the denture adhesive and denture adhesive for dry mouth remained high, while that of the oral moisturizer and denture moisturizer significantly decreased. Between rest and function, the retentive force of the denture adhesive and denture adhesive for dry mouth was high, and that of the oral moisturizer was low.Conclusions: Immediately after use, denture adhesive for dry mouth exhibited high retentive force, but retention gradually decreased due to its water content. Clinical Significance: Denture adhesives for dry mouth can be useful for retaining dentures during 30-min meals.