harmonic drive
Recently Published Documents


TOTAL DOCUMENTS

363
(FIVE YEARS 67)

H-INDEX

20
(FIVE YEARS 1)

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 215
Author(s):  
Hongli Jia ◽  
Hongbing Xin

In contrast to the conventional forced wave generator which consists of cam and flexible bearing in harmonic drive, the novel forced wave generator retains cam but cancels flexible bearing. In this article, the lubrication characteristics of the novel forced wave generator in harmonic drive is studied. First, an elliptical sliding bearing (ESB) model of simplified structure between the novel forced wave generator and the flex spline is established. Further, the computational fluid dynamics (CFD) method is employed to study the effect of some factors on the lubrication characteristics of the ESB model including elliptical gap ratio, width, and rotational speed. According to the analysis, the elliptical gap ratio has a great impact and its optimal value is 3, which is used in the design of the novel forced wave generator. Last, the practical design of the novel forced wave generator in harmonic drive is given, which can provide a basis for design and optimization of a forced wave generator without flexible bearing of the harmonic drive.


2021 ◽  
pp. 46-55
Author(s):  
Vivens Irakoze ◽  
Marco Ceccarelli ◽  
Matteo Russo

2021 ◽  
pp. 485-494
Author(s):  
Xinyu Ji ◽  
Zheqing Zuo ◽  
Xibin Guo ◽  
Xiancheng Song ◽  
Qiang Xu

Machines ◽  
2021 ◽  
Vol 9 (9) ◽  
pp. 194
Author(s):  
Qiang Xin ◽  
Chongchong Wang ◽  
Chin-Yin Chen ◽  
Guilin Yang ◽  
Long Chen

The vibration caused by resonance modes frequently occurs during acceleration and deceleration of the modular joint integrated with flexible harmonic drive. The conventional equivalent rigid-body velocity method with observer can suppress the residual vibration induced by resonant frequency but has poor robustness to model uncertainties and external disturbances. Moreover, it cannot eliminate the torque ripple caused by the harmonic drive during low-speed uniform motion, reducing the velocity tracking accuracy. Hence, a velocity controller with a rigid-body state observer and an adjustable damper is designed to improve the robust performance and velocity tracking accuracy. The designed rigid-body state observer allows a higher gain so that the bandwidth of the observer can increase, and the equivalent rigid-body velocity can be acquired more accurately. Notably, the high gain observer reduces the sensitivity to model uncertainties and exotic disturbances, especially near the resonant frequency. In addition, the observer combined with an adjustable damper can suppress the residual vibration and torque ripple simultaneously. The proposed method is compared experimentally with a PI method and two other rigid-body velocity methods, such as the conventional equivalent rigid-body observer method and the self-resonance cancellation method, to verify its advantages.


Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5057
Author(s):  
Slavomir Hrcek ◽  
Frantisek Brumercik ◽  
Lukas Smetanka ◽  
Michal Lukac ◽  
Branislav Patin ◽  
...  

The aim of the presented study was to perform a global sensitivity analysis of various design parameters affecting the lost motion of the harmonic drive. A detailed virtual model of a harmonic drive was developed, including the wave generator, the flexible ball bearing, the flexible spline and the circular spline. Finite element analyses were performed to observe which parameter from the harmonic drive geometry parameter group affects the lost motion value most. The analyses were carried out using 4% of the rated harmonic drive output torque by the locked wave generator and fixed circular spline according the requirements for the high accuracy harmonic drive units. The described approach was applied to two harmonic drive units with the same ratio, but various dimensions and rated power were used to generalize and interpret the global sensitivity analysis results properly. The most important variable was for both harmonic drives the offset from the nominal tooth shape.


2021 ◽  
Vol 38 (9) ◽  
pp. 701-705
Author(s):  
Joo Yeon Kim ◽  
Dae Sung Bae ◽  
Jae Duk Jang

Actuators ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 203
Author(s):  
Mark J. Nandor ◽  
Maryellen Heebner ◽  
Roger Quinn ◽  
Ronald J. Triolo ◽  
Nathaniel S. Makowski

The development of powered assistive devices that integrate exoskeletal motors and muscle activation for gait restoration benefits from actuators with low backdrive torque. Such an approach enables motors to assist as needed while maximizing the joint torque muscles, contributing to movement, and facilitating ballistic motions instead of overcoming passive dynamics. Two electromechanical actuators were developed to determine the effect of two candidate transmission implementations for an exoskeletal joint. To differentiate the transmission effects, the devices utilized the same motor and similar gearing. One actuator included a commercially available harmonic drive transmission while the other incorporated a custom designed two-stage planetary transmission. Passive resistance and mechanical efficiency were determined based on isometric torque and passive resistance. The planetary-based actuator outperformed the harmonic-based actuator in all tests and would be more suitable for hybrid exoskeletons.


Sign in / Sign up

Export Citation Format

Share Document